Transpak H-22 Guide

SPARE PARTS LIST
OPERATION INSTRUCTIONS
&
H-25 (Tensioner for cord strap, 9 mm- 25 mm)
H-22 (Tensioner for cord strap, 9 mm- 19 mm)
Made in Taiwan
09/2016

OPERATION INSTRUCTIONS
-1-
1./ 2. Put strap around the package. Insert
strap into the buckle and tighten
strap by hand.
3. Take the tensioner by the right
hand and depress tension lever.
Place strap under the gripper so that
it touches the housing with the right
hand edge. Release tension lever.
4. Insert the upper strap into the slot
of the cutter mechanism and the
windlass. Hold the tool and strap
with your left hand and move the
tension lever forth and back until
the strap is tensioned.
5. Depress the tension lever from the
tensioner completely until the strap
is cut. Pivot the tensioner away
from the strap.
MAINTENANCE INSTRUCTIONS
PERIODICALLY LUBRICATE ALL MOVING PARTS WITH ONE OR TWO DROPS OF LIGHT
MACHINE OIL.
CLEAN CLAMP OF ANY DIRT OR STRAP RESIDUE DAILY.

THIS TOOL WAS DESIGNED AND MANUFACTURED FOR SAFE
HANDLING DURING THE STRAPPING OPERATION. FOR
EFFECTIVE SERVICE, PLEASE READ AND FOLLOW ALL
SAFETY, MAINTENANCE AND OPERATING INSTRUCTIONS.
1.
ALWAYS WEAR EYE, FACE, AND HAND PROTECTION WHEN
OPERATING THIS TOOL.
2.
DO NOT PUT HANDS OR OTHER PARTS OF THE BODY
BETWEEN THE STRAP AND THE PACKAGE.
3.
WHEN CUTTING THE STRAP, HOLD THE UPPER PORTION AND
STAND AT A SAFE DISTANCE AWAY FROM THE STRAP. EXERT
CAUTION, AS THE LOWER STRAP WILL SNAP FORWARD.
4.
DO NOT STAND IN LINE WITH THE STRAP WHILE IT IS BEING
TENSIONED. THE STRAP COULD BREAK IF OVER TENSIONED.
5.
USE ONLY ORIGINAL REPLACEMENT PARTS.
6.
SAFETY INSTRUCTIONS
-2-

-3-
REF.
NO. PART NO. DESCRIPTION Q'TY REF. NO. PART NO. DESCRIPTION Q'TY
* PLEASE ORDER PARTS BY PARTS NO.,DESCRIPTION AND Q'TY.
H-22 ( Tensioner for cord strap, 9 mm- 19 mm )
Big Bushing (Base) 1
2
H21-004 Bushing 2
H21-003
1
1
1
3
1
1
4
H22-018 Gripper Plate
18
H21-019 Gripper Screw
19
H21-022 Releasing Lever
22
H21-024 Releasing Lever Roller
24
H21-025 Releasing Lever Shaft
25
1
H21-028 Main Spring
28
33 H21-033 Toggle 2
35 H21-035 Base Shaft 1
1
H21-036 Handle Shaft
1
1
1
36
1
1
H21-038 Blade Lever
38
40 H22-040 Cutting Set
HBS0408 HBS, M4x8
41
HBS0406 HBS, M4x6
42
Handle
43
Base Toggle Spring
Gripper
Gripper Spring
1
1
H21-047 Handle Toggle Spring
47
1
H21-048 Windlass
48
1
H21-049 Ratchet Wheel
49
SR20 Stop Ring, S-20
50 1
1
29 H21-029 Main Spring Bushing 1
30 SP0420 Spring Pin, 4x20 1
1
H21-032 Big Bushing (Handle)
32
H21-002 Small Bushing 2
H22-001 Base 1
8H21-008
H21-015
H21-017
17
15
1
1
53 H21-053 Nose Hook 1
STRAPPING TENSIONER
H21-044

-4-
REF.
NO. PART NO. DESCRIPTION Q'TY REF. NO. PART NO. DESCRIPTION Q'TY
* PLEASE ORDER PARTS BY PARTS NO.,DESCRIPTION AND Q'TY.
H-25 ( Tensioner for cord strap, 9 mm- 25 mm )
Big Bushing (Base) 1
2
TAL1010 Needle Bearing, 1010 2
H21-003
1
1
1
3
1
1
4
H25-018 Gripper Plate
18
H21-019 Gripper Screw
19
H21-022 Releasing Lever
22
H21-024 Releasing Lever Roller
24
H21-025 Releasing Lever Shaft
25
1
H21-028 Main Spring
28
33 H21-033 Toggle 2
35 H21-035 Base Shaft 1
1
H21-036 Handle Shaft
1
1
1
36
1
1
H21-038 Blade Lever
38
40 H25-040 Cutting Set
HBS0408 HBS, M4x8
41
HBS0406 HBS, M4x6
42
H25-043 Handle
43
Base Toggle Spring
Gripper
Gripper Spring
1
1
H21-047 Handle Toggle Spring
47
1
H25-048 Windlass
48
1
H21-049 Ratchet Wheel
49
SR20 Stop Ring, S-20
50 1
1
29 H21-029 Main Spring Bushing 1
30 SP0420 Spring Pin, 4x20 1
1
H21-032 Big Bushing (Handle)
32
H21-002 Small Bushing 2
H25-001 Base 1
8H21-008
H25-015
H21-017
17
15
1
1
53 H21-053 Nose Hook 1
STRAPPING TENSIONER