Traxon Osram Media Tube Go User manual

Media Tube®Go
Installation Guide
V1.0
Cover:
Media Tube®Go RGBW
Media Tube®Go DW

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 2 of 21
CONTENT
1. Safety and Operation 3
2. Introduction 4
3. Installation 8
4. System Configuration 13
5. Care and Maintenance 17
6. Troubleshooting 18
7. Technical Specification 19
8. Warranty Statement 20
For your own safety and that of the product, please read this installation guide
carefully before beginning setup and installation.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 3 of 21
1. Safety and Operation
— CAUTION - Unplug the power supply from the mains power before connecting any cables as this can damage
the products.
— CAUTION - Avoid looking directly into the LED light source at close range for your own safety.
— Persons installing this product should make sure:
1. The installation complies with all applicable codes, state and local laws, ordinances, standards and
safety regulations.
2. The installation environment is carefully studied and suitable surge protection measure(s) is taken.
3. He or she is qualified for the handling of electrical equipment.
— Do not attempt to install or use the product until installation instructions and safety labels are fully understood.
This product is designed for indoor and outdoor use.
— Ensure product operates within the specified temperature range. (Refer to 7. TECHNICAL SPECIFICATION for
more details.)
— The Media Tube®Go does not contain any user-serviceable parts. Opening of the luminaire will void the
warranty.
— Do not use the product if any part of it, or the power cables are damaged.
— Only use product for specified voltage, do not exceed. (Refer to 7. TECHNICAL SPECIFICATION for more
details.)
— Always maintain connection to ensure waterproofing.
— If the product has been subjected to drastic temperature variances, for example, following transportation, do
not connect the fixture until it has reached room temperature, as moisture condensation may cause electric
shock and product damage.
— When installing the products and system power supplies, please ensure they will not be exposed to moisture
and extreme heat (and direct sunlight for outdoor products). Keep a clean operating environment for the fixtures
and system power supplies.
— Please study this Installation Guide thoroughly and check the latest Technical Specification Sheets available
from the Traxon website www.traxontechnologies.com and www.osram.us/traxon before setup.
— Any non-compliance of the Installation Guide will void the Traxon warranty.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 4 of 21
2. Introduction
2.1 General
Media Tube® Go Diffused View Length Maximum number of pixels (PXL)
MEDIA TUBE GO DIFFUSED 2410 RGBW 20PXL 2410mm / 94.9” 20
MEDIA TUBE GO DIFFUSED 1210 RGBW 10PXL 1210mm / 47.6” 10
MEDIA TUBE GO DIFFUSED 370 RGBW 3PXL 370mm / 14.6” 3
MEDIA TUBE GO DIFFUSED 2410 DW 24PXL 2410mm / 94.9” 24
MEDIA TUBE GO DIFFUSED 1210 DW 12PXL 1210mm / 47.6” 12
MEDIA TUBE GO DIFFUSED 310 DW 3PXL 310mm / 12.2” 3
Media Tube® Go Clear View Length Maximum number of pixels (PXL)
MEDIA TUBE GO CLEAR 2410 RGBW 20PXL 2410mm / 94.9” 20
MEDIA TUBE GO CLEAR 1210 RGBW 10PXL 1210mm / 47.6” 10
MEDIA TUBE GO CLEAR 370 RGBW 3PXL 370mm / 14.6” 3
MEDIA TUBE GO CLEAR 2410 DW 24PXL 2410mm / 94.9” 24
MEDIA TUBE GO CLEAR 1210 DW 12PXL 1210mm / 47.6” 12
MEDIA TUBE GO CLEAR 310 DW 3PXL 310mm / 12.2” 3
Media Tube®Go is a slim, direct view luminaire designed for all budgets to integrate into any wall, façade or media
lighting application with tight installation requirements. Available in Clear View or Diffused View and 10 pixels per
1.2 meters / 2.5 pixels per foot, the Media Tube®Go ensures smooth effects along your facade, media application
or bridge.
This product is intended for use in high-quality colored light applications.
Features:
— Available lengths: 370mm / 1ft (3PXL), 1210mm / 4ft (10PXL), 2410mm / 8ft (20PXL) for RGBW
— 310mm / 1ft (3PXL), 1210mm / 4ft (12PXL), 2410mm / 8ft (24PXL) for DW
— Diffused view and clear view
— Two color options: RGBW, DW (2200K - 6500K)
— DMX512
— Daisy Chain System with quick lock connectors
— Manual Addressing with TX Smart Addresser
— IK08 & ANSI 3G Vibration Rated
— IP67 Outdoor, suitable for coastal environments

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 5 of 21
2.2 Dimensions
FIG.1: Media Tube®Go RGBW
See DETAIL A
DETAIL A
54.2mm/2.13”
40mm/1.57”
24mm/0.94”
W1
W2
H
370mm / 1210mm / 2410mm x 25mm x 56.5mm
14.57” / 47.64” / 94.88” x 0.98” x 2.22”
FIG.2: Media Tube® Go DW
See DETAIL A
DETAIL A
54.2mm/2.13”
40mm/1.57”
24mm/0.94”
W1
W2
H
310mm / 1210mm / 2410mm x 25mm x 56.5mm
12.20” / 47.64” / 94.88” x 0.98” x 2.22”
NOTE: Please see CAD files for additional dimensional data.
NOTE: Please see CAD files for additional dimensional data.
W1 W2 H
370mm / 15” 25mm/0.98” 33.5mm/1.32” 60.3mm/2.27”
1210mm / 48” 25mm/0.98” 33.5mm/1.32” 60.3mm/2.27”
2410mm / 95” 25mm/0.98” 33.5mm/1.32” 60.3mm/2.27”
W1 W2 H
310mm / 12” 25mm/0.98” 33.5mm/1.32” 60.3mm/2.27”
1210mm / 48” 25mm/0.98” 33.5mm/1.32” 60.3mm/2.27”
2410mm / 95” 25mm/0.98” 33.5mm/1.32” 60.3mm/2.27”

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 6 of 21
FIG.3: Media Tube® Go Accessories
5-pin interconnection cable (AM463780055/AM463790055/AM463800055)
Starter cable (AM463750055/AM463760055)
0.14m, 1m, 3m / 5.51”, 39.37”, 118.11”
φ7.20mm/0.28”
2*18AWG+3*22AWG
2*18AWG+3*22AWG
1m, 3m / 39.37”, 118.11”
RJ45 Starter Cable (AM463820055)
Power injector cable (AM463810055)
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
19.00m/0.75"
18.00m/0.71"
18.00m/0.71"
2-pin Power Connector
(x1 included)
48.50mm/1.91"
46.50mm/1.83" 30.00mm/1.82"
46.50mm/1.83"
18.00m/0.71"
46.50mm
/1.83"
φ6.80mm/0.27”
φ5.00mm/0.20”
2*17AWG
Network Cable
25.00m/0.98"
34.50mm/1.36"
IP66 Rated RJ45 Boot (x1 included)
18.00m/0.71"
φ7.20mm/0.28”
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
2*17AWG+3*20AWG
46.50mm/1.83"
φ7.20mm/0.28”
18.00m/0.71" 19.00m/0.75"
48.50mm/1.91"
46.50mm/1.83"
φ6.80mm/0.27”
φ7.20mm/0.28”
2*17AWG
2*17AWG+3*20AWG
2*17AWG+3*20AWG
φ7.20mm/0.28”
46.50mm/1.83"
18.00m/0.71"
End Cap with 120Ω terminator(AM463770055)
48.50mm/1.91"
19.00m/0.75"

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 7 of 21
2.3 Packing Contents
FIG.4: Packing Contents
1 Media Tube® Go Clear/Diffused View
2 Mounting brackets

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 8 of 21
3. Installation
3.1 Points To Consider
Plan your installation before mounting the Media Tube®Go. The following should be considered for a successful
installation.
— Weather conditions and ambient temperature of installation site.
— Appropriate cable lengths (cable gauges described in system diagram). Please consult your local Traxon office
or authorized agent for necessary aid.
— The number of the Media Tube®Go and appropriate LED Engines.
— DMX512 to be used to control the Media Tube®Go.
— Distance between each Tube for thermal expansion and maintaining pixel pitch.
— Mounting distances.
— Proper surge protection.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 9 of 21
FIG.5: Media Tube®Go Cable System
Starter Cable
From terminal block to first Media Tube®Go in chain
Interconnection Cable
From Media Tube®Go to another Media Tube®Go
RJ45 Starter Cable
For RJ45 connection
5-pin interconnection cable (AM463780055/AM463790055/AM463800055)
Starter cable (AM463750055/AM463760055)
0.14m, 1m, 3m / 5.51”, 39.37”, 118.11”
φ7.20mm/0.28”
2*18AWG+3*22AWG
2*18AWG+3*22AWG
1m, 3m / 39.37”, 118.11”
RJ45 Starter Cable (AM463820055)
Power injector cable (AM463810055)
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
19.00m/0.75"
18.00m/0.71"
18.00m/0.71"
2-pin Power Connector
(x1 included)
48.50mm/1.91"
46.50mm/1.83" 30.00mm/1.82"
46.50mm/1.83"
18.00m/0.71"
46.50mm
/1.83"
φ6.80mm/0.27”
φ5.00mm/0.20”
2*17AWG
Network Cable
25.00m/0.98"
34.50mm/1.36"
IP66 Rated RJ45 Boot (x1 included)
18.00m/0.71"
φ7.20mm/0.28”
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
2*17AWG+3*20AWG
46.50mm/1.83"
φ7.20mm/0.28”
18.00m/0.71" 19.00m/0.75"
48.50mm/1.91"
46.50mm/1.83"
φ6.80mm/0.27”
φ7.20mm/0.28”
2*17AWG
2*17AWG+3*20AWG
2*17AWG+3*20AWG
φ7.20mm/0.28”
46.50mm/1.83"
18.00m/0.71"
End Cap with 120Ω terminator(AM463770055)
48.50mm/1.91"
19.00m/0.75"
5-pin interconnection cable (AM463780055/AM463790055/AM463800055)
Starter cable (AM463750055/AM463760055)
0.14m, 1m, 3m / 5.51”, 39.37”, 118.11”
φ7.20mm/0.28”
2*18AWG+3*22AWG
2*18AWG+3*22AWG
1m, 3m / 39.37”, 118.11”
RJ45 Starter Cable (AM463820055)
Power injector cable (AM463810055)
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
19.00m/0.75"
18.00m/0.71"
18.00m/0.71"
2-pin Power Connector
(x1 included)
48.50mm/1.91"
46.50mm/1.83" 30.00mm/1.82"
46.50mm/1.83"
18.00m/0.71"
46.50mm
/1.83"
φ6.80mm/0.27”
φ5.00mm/0.20”
2*17AWG
Network Cable
25.00m/0.98"
34.50mm/1.36"
IP66 Rated RJ45 Boot (x1 included)
18.00m/0.71"
φ7.20mm/0.28”
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
2*17AWG+3*20AWG
46.50mm/1.83"
φ7.20mm/0.28”
18.00m/0.71" 19.00m/0.75"
48.50mm/1.91"
46.50mm/1.83"
φ6.80mm/0.27”
φ7.20mm/0.28”
2*17AWG
2*17AWG+3*20AWG
2*17AWG+3*20AWG
φ7.20mm/0.28”
46.50mm/1.83"
18.00m/0.71"
End Cap with 120Ω terminator(AM463770055)
48.50mm/1.91"
19.00m/0.75"
5-pin interconnection cable (AM463780055/AM463790055/AM463800055)
Starter cable (AM463750055/AM463760055)
0.14m, 1m, 3m / 5.51”, 39.37”, 118.11”
φ7.20mm/0.28”
2*18AWG+3*22AWG
2*18AWG+3*22AWG
1m, 3m / 39.37”, 118.11”
RJ45 Starter Cable (AM463820055)
Power injector cable (AM463810055)
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
19.00m/0.75"
18.00m/0.71"
18.00m/0.71"
2-pin Power Connector
(x1 included)
48.50mm/1.91"
46.50mm/1.83" 30.00mm/1.82"
46.50mm/1.83"
18.00m/0.71"
46.50mm
/1.83"
φ6.80mm/0.27”
φ5.00mm/0.20”
2*17AWG
Network Cable
25.00m/0.98"
34.50mm/1.36"
IP66 Rated RJ45 Boot (x1 included)
18.00m/0.71"
φ7.20mm/0.28”
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
2*17AWG+3*20AWG
46.50mm/1.83"
φ7.20mm/0.28”
18.00m/0.71" 19.00m/0.75"
48.50mm/1.91"
46.50mm/1.83"
φ6.80mm/0.27”
φ7.20mm/0.28”
2*17AWG
2*17AWG+3*20AWG
2*17AWG+3*20AWG
φ7.20mm/0.28”
46.50mm/1.83"
18.00m/0.71"
End Cap with 120Ω terminator(AM463770055)
48.50mm/1.91"
19.00m/0.75"
Power Injector Cable
For power connection
5-pin interconnection cable (AM463780055/AM463790055/AM463800055)
Starter cable (AM463750055/AM463760055)
0.14m, 1m, 3m / 5.51”, 39.37”, 118.11”
φ7.20mm/0.28”
2*18AWG+3*22AWG
2*18AWG+3*22AWG
1m, 3m / 39.37”, 118.11”
RJ45 Starter Cable (AM463820055)
Power injector cable (AM463810055)
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
19.00m/0.75"
18.00m/0.71"
18.00m/0.71"
2-pin Power Connector
(x1 included)
48.50mm/1.91"
46.50mm/1.83" 30.00mm/1.82"
46.50mm/1.83"
18.00m/0.71"
46.50mm
/1.83"
φ6.80mm/0.27”
φ5.00mm/0.20”
2*17AWG
Network Cable
25.00m/0.98"
34.50mm/1.36"
IP66 Rated RJ45 Boot (x1 included)
18.00m/0.71"
φ7.20mm/0.28”
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
2*17AWG+3*20AWG
46.50mm/1.83"
φ7.20mm/0.28”
18.00m/0.71" 19.00m/0.75"
48.50mm/1.91"
46.50mm/1.83"
φ6.80mm/0.27”
φ7.20mm/0.28”
2*17AWG
2*17AWG+3*20AWG
2*17AWG+3*20AWG
φ7.20mm/0.28”
46.50mm/1.83"
18.00m/0.71"
End Cap with 120Ω terminator(AM463770055)
48.50mm/1.91"
19.00m/0.75"
End cap includes DMX data terminator
5-pin interconnection cable (AM463780055/AM463790055/AM463800055)
Starter cable (AM463750055/AM463760055)
0.14m, 1m, 3m / 5.51”, 39.37”, 118.11”
φ7.20mm/0.28”
2*18AWG+3*22AWG
2*18AWG+3*22AWG
1m, 3m / 39.37”, 118.11”
RJ45 Starter Cable (AM463820055)
Power injector cable (AM463810055)
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
19.00m/0.75"
18.00m/0.71"
18.00m/0.71"
2-pin Power Connector
(x1 included)
48.50mm/1.91"
46.50mm/1.83" 30.00mm/1.82"
46.50mm/1.83"
18.00m/0.71"
46.50mm
/1.83"
φ6.80mm/0.27”
φ5.00mm/0.20”
2*17AWG
Network Cable
25.00m/0.98"
34.50mm/1.36"
IP66 Rated RJ45 Boot (x1 included)
18.00m/0.71"
φ7.20mm/0.28”
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
2*17AWG+3*20AWG
46.50mm/1.83"
φ7.20mm/0.28”
18.00m/0.71" 19.00m/0.75"
48.50mm/1.91"
46.50mm/1.83"
φ6.80mm/0.27”
φ7.20mm/0.28”
2*17AWG
2*17AWG+3*20AWG
2*17AWG+3*20AWG
φ7.20mm/0.28”
46.50mm/1.83"
18.00m/0.71"
End Cap with 120Ω terminator(AM463770055)
48.50mm/1.91"
19.00m/0.75"

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 10 of 21
3.2 Pre-Installation Checks
3.2.1 Installation Checklist
1. Prepare cables and all necessary accessories (Waterproof Quick Lock End Caps etc).
2. Perform functional check of the Media Tube®Go. Take care not to damage cables/connectors during pre-
installation checks.
3. Ensure all pre-installation checks laid out below have been followed.
4. Mount the Media Tube®Go on-site. If the installation is to be left uncompleted overnight, place all non-
connected LED Engines and the Media Tube®Go in an indoor environment.
5. All units must be connected or utilize end caps to protect from water ingress.
Ensure all the Interconnection Cables, Media Tube®Go and LED Engines are initially stored in a dry area to
guarantee the complete sealing of the system from water before installation.
3.2.2 Mounting Bracket
Mounting hardware (screws, lock washers and washers) are required for mounting the bracket to the surface.
Mounting hardware by others. The mounting brackets can be moved along the extrusion to match installation
requirements.
FIG.6: Mounting Bracket
Mounting Hardware
(by others)
φ4.5mm/0.18’’
40mm/1.57”
24mm/0.94”
3.2.3 Installation Sequence
1. Measure the correct distances for brackets and install the Media Tube®Go fixtures.
2. Connect the Media Tube®Go in the daisy-chain manner outlined in the System Diagram to form large
installations.
3. Perform functional check on all the Media Tube®Go and inspect cables and brackets for any damage. Check
for any abnormalities with the control signal.
4. Report any functional defect found to your nearest Traxon Technologies office. DO NOT attempt to install the
Media Tube®Go with functional defects on-site.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 11 of 21
3.3 On-Site Installation
•DO NOT attempt installation in wet or severe weather conditions.
•DO NOT leave and expose any Media Tube® Go or LED Engines
unconnected under wet/raining or snowing environment.
•IP failure induced by stressed/damaged cables during or after installation
will not be under warranty by Traxon Technologies.
•ALWAYS keep the cables protected from sharp objects and ensure no
damage is generated on the cable.
Failure to keep Media Tube®Go within the operating temperature range of -30°C to +55°C / -22°F to +131°F
and storage temperature range of -40°C to +80°C / -40°F to +176°F will void the product’s warranty.
3.3.1 On-Site Installation
1. Fix brackets to installation surface with anchor bolts or screws (by others).
2. The Media Tube®Go are interconnected using the IN and OUT cables/connectors on each end of the tube.
Connectors will make an audible “click” when connected. Gently pull on the cables in opposites directions to
ensure they are fully locked and do not come loose. The below diagram shows the Tube connections. Always
remember to affix a Quick Lock Waterproof End Cap (sold separately) for the OUT connector of the final Tube
in each daisy chain. See System Diagram for details.
FIG.7: Media Tube®Go Connections
If you do not hear "click", rotate the spring loaded
connector manually to ensure that the connectors
are properly mated.
1
2
“click”
The connector cable can be pulled out
to facilitate the connection between 2 fixtures.
Max length cable can extend from the fixture is 70mm / 2.8".
NOTE: Any water ingress incurred due to improper installation of cable connectors or Waterproof Quick Lock
End Caps will not be covered under warranty by Traxon Technologies.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 12 of 21
3. Be sure not to compress the IN/OUT cables.
NOTE: To keep LED pitch consistent and allow for thermal expansion, be sure to keep a minimum distance of
2mm (0.08”) between consecutive Media Tube® Go (see below diagram).
FIG.8: Keep minimum distance between fixtures
To maintain consistent LED pitch and to allow for thermal expansion, a minimum of
2mm / 0.08" is required between luminaire's. End Cap Seal on Last Tube
≥2mm / 0.08"
4. The first tube of the daisy-chain group has to be connected to the control system via Waterproof Junction
Box (by others).Starter cables, Data and Power cables, and video fiber optic cables have to be installed
through conduit.
5. Set up the control system indoors as detailed in the System Diagram and connect to the Media Tube®Go.
Start each unit and verify correct function.
NOTE: For manual addressing setups, please refer to the configuration guide of TX Smart Addresser (CD.SA.0000100).

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 13 of 21
4. System Configuration
4.1 LED CONTROL
The LEDs on the Media Tube®Go are controlled by DMX512. For RGBW, each pixel on the Tube uses six RGB 3
in 1 LEDs and six white LEDs, for R, G, B and W channels. Pixel number 1 begins on the IN connector side, and it
uses the first four channels. DW work in a similar way, but use less pixels per length.
6 RGBW LEDs
6 RGB LEDs
6 DW LEDs
RGBW
Pixel n Control Channel Number
R +4(n-1) + 1
G +4(n-1) + 2
B +4(n-1) + 3
W +4(n-1) + 4
Where: n is pixel number along the Tube.
(Pixel 1 is located near the IN connector.)
6 RGBW LEDs
6 RGB LEDs
6 DW LEDs
DW
Pixel n Control Channel Number
WW + 2 (n-1) + 1
CW Tube start address +2n
Where: n is pixel number along the Tube.
(Pixel 1 is located near the IN connector.)

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 14 of 21
FIG.9: System Diagram (Starter Cable)
AC 120V-277V In
DMX In
AC 120V-277V In Power In
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
Power Supply 24V 100W (AM175860055) Starter Cable, 5-wire, 1m (AM463750055)
Starter Cable, 5-wire, 3m (AM463760055)
Power Injector Cable (AM463810055)
End Cap, 120Ω terminator (AM463770055)
Power Dasiy Chain : Max. 6 x 1.2m/3.94’ fixtures
NOTE: The Address wire only needs to be connected during address configuration, it is not needed during operation. Wiring diagram shows only typical connections. Max. number of fixtures is based on minimal interconnection lengths. Actual number of fixtures is dependent on cable interconnections. Number of fixtures will reduce if longer cable lengths are used. Consult with your regional sales office to confirm maximums.
FIG.10: System Diagram (Injector Cable)

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 15 of 21
AC 120V-277V In
DMX In
AC 120V-277V In
Power In*
Power In
Pin Color Connection
Yellow-green Addressing
Gray DMX-
Black DMX+
Blue 24V-
Brown 24V+
Power Injector Cable (AM463810055)
RJ45 Starter Cable (AM463820055)
Power Supply 24V 100W (AM175860055)
Power Dasiy Chain : Max 6 x 1.2m/3.94’ fixtures
End Cap, 120Ω terminator (AM463770055)
NOTE: The Address wire only needs to be connected during address configuration, it is not needed during operation. Wiring diagram shows only typical connections. Max. number of fixtures is based on minimal interconnection lengths. Actual number of fixtures is dependent on cable interconnections. Number of fixtures will reduce if longer cable lengths are used. Consult with your regional sales office to confirm maximums.
*Connectors included with RJ45 Starter Cable.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 16 of 21
FIG.11: Orientation and Color Mixing
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT IN
OUT IN
OUT IN
OUT IN
OUT IN
OUT IN
OUT
IN
OUT
IN
OR
“Snake Mode” “Snake Mode”
OR
• For best color mixing results, ensure the tubes have the same orientation and remain parallel to the
main movement pattern of the veiwer.
• If same orientation cannot be achieved, ensure the orientation of the tubes that snake back are
180° to the previous row / column and consider the main movement pattern of the viewer.
For left or right viewing angles, align the tubes left to right or right to left.
For top or bottom viewing angles, align the tubes top to bottom or bottom to top.
Main movement pattern
Main movement pattern
OUT
IN

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 17 of 21
5. Care and Maintenance
Traxon products are of superior design and quality and should be treated with care. The recommendations below
will help fulfill any warranty obligations and gain good use and longevity from the products.
— Do not attempt or use the product(s) until you read and understand the installation instructions. Failure to
adhere to these instructions could result in serious injury or property damage.
— Do not use product(s) if cables are damaged.
— Do not connect cables and connectors when wet or in wet area. Moisture on bare connectors can cause
electric shock and damage to product(s).
— Do not use product(s) in extreme heat environment. Ensure there is sufficient airflow and use cool air circulation
if required.
— Do not drop, knock, or shake product(s). Rough handling can damage the electronics and void the warranty.
— Do not use harsh chemicals, cleaning solvents, or strong detergents to clean products. Wipe with a damp
cloth on housings and a dry cloth on electronics to remove dirt or dust.
— Do not attempt to service or repair the product(s) unless done by an authorized service personnel. Contact
your local Traxon office or distributor for details.
— If the product is not working as specified, please contact your nearest authorized service center or Traxon
Technologies office for assistance.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 18 of 21
6. Troubleshooting
CAUTION: Ensure power supply is OFF when disconnecting / connecting cables.
Problem Cause Possible Solutions
Product does NOT light
up after installation
Incorrect power
connection
— Check Mains Power
— Check power supply leads and wire connections
— Ensure output wires are connected with proper
polarity
— Check if LED Engine’s secondary output is working
as specified.
Shadowing Light source covered — Check for cables, wires or unwanted debris
covering LED light source
Modules are dim Excess products
connected
— Ensure the power supplies are not overloaded due
to an excess of products connected
Flickering Incorrect power input/
Excess products
connected
— Ensure the input voltage is correct
— Ensure the power supplies are not overloaded due
to an excess of products connected
If problems persist or the product is not working as specified, please contact your nearest authorized service
center or Traxon Technologies office for assistance.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 19 of 21
7. Technical Specification
Media Tube®Go RGBW
Clear View Diffused View
370mm
15”
1210mm
48”
2410mm
95”
370mm
15”
1210mm
48”
2410mm
95”
Number of Pixel 3 pixels 10 pixels 20 pixels 3 pixels 10 pixels 20 pixels
Light Source: 18 RGBW
4-in-1
60 RGBW
4-in-1
120 RGBW
4-in-1
18 RGBW
4-in-1
60 RGBW
4-in-1
120 RGBW
4-in-1
Color Range: RGBW (White CCT: 6500K standard)
Beam Angle: 120° 110°x170°
Power Input*: 24V DC
Power Consumption (typ).: 4.5W / 15W / 30W
Weight: 0.39kg /
0.86lb
0.88kg /
1.94lb
1.62kg /
3.57lb
0.39kg /
0.86lb
0.88kg /
1.94lb
1.62kg /
3.57lb
Operating Temperature: -30°C to +55°C / -22°F to +131°F
Storage Temperature: -40°C to +80°C / -40°F to +176°F
Media Tube®Go DW
Clear View Diffused View
310mm
12”
1210mm
48”
2410mm
95”
310mm
12”
1210mm
48”
2410mm
95”
Number of Pixel 3 pixels 12 pixels 24 pixels 3 pixels 12 pixels 24 pixels
Light Source: 18 2200K
+18 6500K
72 2200K
+72 6500K
144 2200K
+144 6500K
18 2200K
+18 6500K
72 2200K
+72 6500K
144 2200K
+144 6500K
Color Range: DW (White CCT: 2200-6500K)
Beam Angle: 120° 110°x170°
Power Input*: 24V DC
Power Consumption (typ).: 4.5W / 15W / 30W
Weight: 0.39kg /
0.86lb
0.88kg /
1.94lb
1.62kg /
3.57lb
0.39kg /
0.86lb
0.88kg /
1.94lb
1.62kg /
3.57lb
Operating Temperature: -30°C to +55°C / -22°F to +131°F
Storage Temperature: -40°C to +80°C / -40°F to +176°F
As with all electronic devices, LED output degrades over time - a term called lumen depreciation. This also
explains why it is nearly impossible to expect photometric performances of two LED products with different service
life spans to be the same. The rate of LED degradation is a complex function of many factors such as operating
efficiency, duration of continuous operation, and operating conditions (e.g. ambient temperature).
Because LEDs are semiconductor devices, their performances are subject to inherent variability commonly found
in semiconductor industry. To improve consistency in performance across the same product, LED manufacturers
“sort” LEDs into bins according to different preset parameters, such as forward driving voltage, illumination,
etc. Whereas binning is a sorting function, it is not a correction process. Inherent variability in the manufacturing
process always results in different binning distributions according to different production lots. Traxon uses
automatically binned LEDs on its products, thereby minimizing output variations within the model range.

www.traxontechnologies.com | www.osram.us/traxon
©2022 TRAXON TECHNOLOGIES - AN OSRAM BUSINESS. ALL RIGHTS RESERVED. TRAXON™, TX CONNECT®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS, OTHER PATENTS
PENDING. SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Installation Guide V1.0 04/22 P. 20 of 21
8. Warranty Statement
Traxon Technologies warrants its Products against material or workmanship defects for a period of five (5) years
from date of purchase, provided that the purchased items are used under the conditions stated in this user
manual.
Please refer www.traxontechnologies.com and www.osram.us/traxon for all warranty terms and conditions.