Traxxas Pro Scale Mercedes-Benz G 500 User manual

Covers Part #8898X
Pro Scale
®
Advanced Lighting Control System Installation Instructions -
Mercedes-Benz
®
G 500
®
& G 63
®
TRAXXAS.com
Traxxas, 6250 Traxxas Way, McKinney, TX 75070, Phone: [phone], Fax: [phone], e-mail: [email protected]
HKC21016-R00 Rev 220121
Visitez Traxxas.com/manuals pour télécharger
les instructions dans votre langue.
Visite la página Traxxas.com/manuals para
descargar el instrucciones en su idioma.
Auf Traxxas.com/manuals, können Sie
anleitung in Ihrer Sprache downloaden.
CAUTION: RISK OF INJURY!
Use care with hobby knives, tapered reamers, and other cutting tools as they
are extremely sharp and can cause severe injury, deep cuts, and/or punctures.
PRO-SCALE
DISTRIBUTION
BLOCK
#XXXX
™
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
The Traxxas Pro Scale® Advanced Lighting Control
System for your Mercedes-Benz®G 500®4x42 or G 63®
AMG consists of two major electronic components:
the Pro Scale Lighting Power Module and the Pro
Scale Lighting Distribution Block.
The Lighting Power Module installs on the chassis
and performs as the voltage regulator and power
supply for the lighting system. It also controls
various lighting functions through the two buttons
on the face of the module and communicates with
the receiver in the model via the communication
cable or the optional included MAXX® Link cable.
The Lighting Distribution Block mounts in the body
of the vehicle and is the distribution hub for all the
various wired lights in your Mercedes-Benz® body.
Its main function is to direct power and instructions
to the brake lights, reverse lights, turn signals, and
high/low beam lighting.
There is only one rugged breakaway wiring connector
between the Lighting Distribution Block and
the Lighting Power Module for reliable lighting
performance, plus it makes it easy to remove the body
for vehicle service. The connector is designed to break
away from the vehicle, without damage, if the body
comes off the vehicle in a crash. There are lighting
channels on the Lighting Power Module which allow
the lighting installed on the chassis to be permanently
connected and integrated into the system. This is
helpful to install features such as rock lights, bumper
lights, and other chassis-mounted accessory lighting.
CAUTION: RISK OF DAMAGE TO BATTERIES!
Always disconnect the battery from the ESC when not in use to prevent the
possibility of over-discharge and battery damage.
Kit Contents:
• Pro Scale Lighting Power Module
• Power module chassis mount
• Pro Scale Lighting Distribution Block
• Lighting Distribution Block mount
• Motor sense wire harness
• Breakaway cable (part of the Lighting
Distribution Block)
• MAXX® Link cable (Data Link)
(TQi Radio System only)
• Receiver communication cable
• Headlight and side marker light
harness assembly
• Roof lights harness
• 2-in-1 wire harness adapter (2)
• Tail lights harness (1)
• Turn signals harness (1)
• Reverse light harness (1)
• Rear fog light harness (1)
• Jumper (1)
• Reverse light lens (right) (1)
• Rear fog light lens (left) (1)
• 2.5x8mm button-head cap screws (4)
• 2.6x8mm button-head cap screw (4)
• 2.5x10mm countersunk cap screw (1)
• 2.5x12mm cap screw (1)
• 2.5x18mm cap screw (1)
• Zip ties (10)
• Zip tie mount (4)
• Silicone grease
Tools required:
• 1.5mm hex wrench (part #3415, sold
separately)
• 2.0mm hex wrench (part #3415, sold
separately)
• Hobby knife or body scissors (part #3431
or #3432, sold separately)
• Wire cutters (to trim
zip ties)
• Small needle nose pliers
AUX
POWER
IN RX INOUT
Part 6592
1
2
3
4
5
6
7
8
9
10
11
12
MOTOR
SENSOR
MAXX LINK
SIGNAL
MODE
PRO SCALE® LIGHTING POWER MODULE
Mode Select
(see table in
Operation section)
Signal Select
(see table in
Operation section)
Breakaway Cable
Connector Port
(connects Power Module
to Lighting Distribution Block)
to Traxxas XL-5 HV Electronic
Speed Control (ESC) or direct
battery power source
up to 3s LiPo or 12.6V
Receiver Communication Cable Port
(connects power module to receiver
using receiver communication cable)
Motor Sense
Connector Port
Auxiliary Power Connector
(3V - always on)
LIGHTING POWER MODULE
TOP VIEW
SIDE VIEW
MAXX® Link Cable Ports
(connects power module to
receiver using MAXX Link cable)
(TQi Radio System only)
COMMUNICATION CABLES
Your Pro Scale Advanced Lighting Control System includes two
communication cables: the Receiver Communication Cable and
the MAXX® Link Cable. Since your model is equipped with the TQi
receiver, you can use either the Receiver Communication Cable or
the MAXX Link Cable. MAXX® Link Cable only: The 6511 Traxxas
Link Wireless Module (sold separately) is required for Traxxas Link App
functionality (only with the MAXX Link Cable). Some models may require
a software update for the TQi receiver via the Traxxas Link App for custom
lighting controls and configurations (see Appendix on page 8 for
additional information).
Only use one of the communication cables to connect the Lighting
Power Module to the receiver. Do not use both cables together.
MAXX®Link Cable
(TQi Radio System only)
Receiver Communication
Cable
LIGHTING DISTRIBUTION BLOCK
1
Wiring connectors for the lights are
labeled with letters and/or colors.
Accessory Connectors
(not used with this kit)

2
A. INSTALL THE LIGHTING POWER MODULE ON THE CHASSIS
1. Install the Power Module mount on the chassis with the included 2.5x10mm
countersunk cap screw (Fig. 1).
2. Install the Lighting Power Module on the mount with the included
2.5x12mm (1) and 2.5x18mm (1) cap screws (Fig. 1).
3. Route the module power wire under the mount. Plug the red male
connector from the ESC into the red female connector from the power wire
(refer to the Chassis Wiring Diagram on page 3 for more detail).
B. WIRE THE LIGHTING POWER MODULE TO THE RECEIVER
1. Plug one end of the Receiver
Communication Cable into the RX
IN port on the Power Module (Fig. 2)
(refer to the Chassis Wiring Diagram
on page 3 for more detail).
2. Remove the 3x10mm counter-sunk
cap screws (2) from the battery tray
(Fig. 3).
3. Lift up the battery tray and route the
Receiver Communication Cable from
the Power Module under the battery
tray and to the receiver box (refer to the Chassis Wiring Diagram on page 3 for
more detail). Use a zip tie (included) to attach the wires to the loop on top of
the transmission housing. Reinstall and tighten the battery tray screws. Note:
Be careful not to pinch or damage any of the wires under the battery tray.
4. Remove the receiver box cover
by removing the three 3x8mm
button-head cap screws (Fig 4).
5. Remove the wire clamp by
removing the two 2.5x8mm cap
screws (Fig 4).
6. Feed the loose end of the
Receiver Communication Cable
connector over the wire guide
and into the receiver box (Fig.
5). To make installation easier,
unplug and remove a few of the
existing wires from the receiver
box. Note the locations
of any unplugged wires.
Use needle nose pliers to
help grab the connectors
and pull them through.
Arrange all wires neatly
between the wire guides
in the receiver box (Fig. 5).
The excess wire will
be bundled inside
the receiver box.
7. Apply a bead of the
included silicone
grease to the wire
clamp (Fig. 6).
8. Be careful not to
damage the wires
(make sure the
wires are in the
wire guides). Reinstall the wire clamp. Tighten the two 2.5x8mm cap screws
securely (Fig. 7).
9. Unplug the electronic speed control (ESC) from the receiver (channel 2).
10. Plug the communication cable into the receiver (Fig. 8): the black connector
with the single blue wire plugs into one of the channel 1 ports; the female
black connector with the 3 black wires plugs into the channel 2 port.
11. Now, plug the black male connector (white, red, black servo cable) from the
ESC into the black female connector (white, red, black servo cable) on the
communication cable (refer to the Chassis Wiring Diagram on page 3 for more
detail). Leave the steering servo cable plugged into the other channel 1 port.
12. Make sure the blue o-ring gasket is properly seated in the groove in the
receiver box so that the cover will not pinch it or damage it in any way.
13. Reinstall the cover on the receiver box and tighten the three 3x8mm button-
head cap screws securely. Inspect the cover to make sure that the O-ring seal
is not visible.
14. Use the supplied zip ties to bundle the wires neatly and attach them to
the vehicle as needed so that loose wires will not become entangled with
moving parts.
C. INSTALL THE MOTOR SENSE WIRING HARNESS
1. Unplug the red and black motor wires (bullet
connectors) from the ESC. Plug the bullet
connectors from the motor and the ESC into the
motor sense wiring harness (red to red and black
to black) (Fig. 9). Plug the harness connector into
the Motor Sensor port on the power module
(refer to the Chassis Wiring Diagram on page 3
for more detail).
2. Use the supplied zip ties
to bundle the wires neatly
and attach them to the
vehicle as needed so
that loose wires will not
become entangled with
moving parts.
D. INSTALL REVERSE LIGHT AND FOG LIGHT WIRING HARNESS
Insert the included reverse light LED (harness labeled for Channel 8) and rear
fog light LED (harness labeled for Channel 5) into the receptacles in the rear
bumper. Be careful not to damage the wires. Fasten the clear reverse light lens
(right side) and red rear fog light lens (left side) to the rear bumper using the
included 2.5x8mm button-head cap screws (4) as shown in Fig. 10.
1. Route the wires from the two harnesses through the wire retainer
channel on the rear bumper (Fig. 11) and to the Pro Scale Lighting Power
Module on the chassis. New zip ties are provided to secure the wires.
The zip ties do not need to be tight; allow some extra length for wire
movement.
2. Plug the rear fog light harness into channel 5 and the reverse light
harness into channel 8 on the Pro Scale Lighting Power Module (refer to
the Chassis Wiring Diagram on page 3 for more detail).
3x8mm BCS
3x8mm BCS
Receiver
Box Cover
2.5x8mm CS
Wire Clamp
Fig. 4
Fig. 6 Fig. 7
Fig. 2Fig. 2
ReceiverReceiver
Communication CableCommunication Cable
Wire GuideWire Guide
Fig. 5Fig. 5
Fig. 3Fig. 3
Battery Tray
3x10mm CCS
(hidden by battery hold down)
Receiver Communication
Cable Black wires to CH2
Receiver Communication
Cable Blue wire to CH1
Servo wire to CH1
to ESC
TQi Receiver
Fig. 8
Fig. 9Fig. 9
2.5x18mm CS
2.5x10mm CCS
Power Module Mount
2.5x12mm BCS
Fig. 1
Fig. 10
2.5x8mm BCS
2.5x8mm BCS
Rear fog
light lens
(red)
Reverse light lens
(clear)
Fig. 11Wire routing

Actual mounting view.
Distribution Block face shown
in the diagram for clarity.
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Rock
Light
Rock
Light
Motor
Chassis Wiring
(top down view)
To Motor Connector
Receiver Communication Cable
To Motor Connector
To ESC
To Receiver
Motor Sense
Connectors
From ESC
From ESC
From CH2
Lighting
Power
Module
Rock
Light
Rock
Light
Rock
Light Rock Light
Rock
Light*
Rock
Light
Rock
Light*
Rock
Light
To ESC
Lighting
Power
Module
FRONT
FRONT
Receiver Communication Cable
Black Wires to CH2
Blue Wire to CH1
Receiver
Route wires under
battery tray
Route wires under
battery tray
To MAXX Link
IN port on
Lighting Power
Module
From ESC
Optional MAXX Link
Cable Wiring
(TQi Receiver Only)
To Receiver
XL-5 HV ESC
Reverse LightFog Light
Jumper
Headlight /
Turn Signal
Roof LightRoof Light
Headlight /
Turn Signal
Side
Marker
Hood
Marker
Hood
Marker
Side
Marker
Disconnect jumper plugs for
Pro Scale Advanced Lighting
Control System use.
Turn SignalTurn Signal
Tail Light /
Brake Light
Tail Light /
Brake Light
Body Wiring
(viewed from the
underside of the body)
Remove stock jumper from board
for Pro Scale Advanced Lighting
Control System use.
**
Breakaway Cable from
Distribution Block mounted on body
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Breakaway Cable
to Lighting Power
Module on chassis
CHASSIS WIRING DIAGRAM
Visit Traxxas.com/ProScaleLighting for
additional information about installing
and connecting accessories such as
auxiliary lighting (rock lights shown, part
#8026X and #8897, each sold separately)
to the Pro Scale Lighting Module.
G 63 shown.
*#8897 rock lights not required for G 500.
**Use the included 2-in-1 wire harness
adapter when installing both rock
light kits on G 63.
3

F. INSTALL HEAD LIGHTS WIRING HARNESS
1. Remove the 2.6x8mm button-head cap screws (A) (8) to remove the
front grille mount (B) and the front grille (C) from the body (refer to
the Lighting Assembly Diagram for more detail). Remove the 1.6x5mm
button-head screws (D) (2) from each headlight lens (E) and remove
the assemblies from the front grille mount. Retain and reuse the plastic
headlight lens, reflectors, reflector lens, and all hardware.
2. Install the circuit boards (F) onto the grille mount. Route the harness
connecting the two circuit boards through the wire retainers on the
front of the mount. Route the jumper wire loops and power wires in the
small slot and over the top of the mount as shown (Fig. 13). Disconnect
the white jumper plugs.
3. Install the reflector lens and chrome reflectors (2 each) onto the circuit
boards (Fig. 14). Note: The reflectors/lens must be installed correctly to
sit flat against the circuit boards. Align the keying features (pegs on the
chrome reflectors and clear lens) with holes in the circuit boards and the
grille mount.
4. Install the headlight lens over the chrome reflectors and onto the circuit
boards (Fig. 15). Note: There are notches on the sides of the plastic
headlight lens for clearance of the wires from the circuit boards.
5. Secure the headlight lens to the grille mount with the 1.6x5mm button-
head screws (4) removed during disassembly.
6. Reinstall the front grille mount and front grille on the body using the
2.6x8mm button-head cap screws (8) removed during disassembly.
7. Remove the 2.6x8mm button-head cap screws (G) from the turn signal
lens and housings on the vehicle hood (H) and remove the blank LEDs
from the receptacles. Reinstall the lens and housings, and then snap the
LED turn signal lights into the receptacles.
8. Insert the LED side marker lights
into the receptacles near each
front side door. Be careful not
to damage the wires. The LEDs
should snap into place. Note:
Bend the wire leads carefully to
assist with wire routing and for
better fitment against the vehicle
body (Fig. 16).
9. Route the wiring harnesses in the
body (refer to the Body Wiring
Diagrams on pages 6 & 7 for
more detail). Use the included zip
ties and zip tie mounts to secure the wiring to the body in the locations
indicated. The zip ties do not need to be tight; allow some extra length for
wire movement.
G. INSTALL TAIL LIGHTS AND TURN SIGNALS WIRING HARNESS
Note: The tail lights harness (I) and rear turn signals harness (J) have a long
and short wire lead. The short wire of each harness should be installed on the
left side (driver side) of the vehicle body . The tail lights harness has the larger
5mm LEDs with the red color band near the connector. The rear turn signals
harness has the smaller 3mm LEDs and is labeled for port B on the Pro Scale
distribution block (Q) .
1. Insert the tail light LEDs into the
tail light receptacles. Be careful
not to damage the wires. The LEDs
should snap into place. Bend the
wire leads to lie flat against the
body and away from the inner
fenders (Fig. 17).
2. Insert the turn signal LEDs into the
turn signal receptacles. T he LEDs
should snap into place.
3. Route the wiring harnesses in the
body (refer to the Body Wiring
Diagrams on pages 6 & 7 for more detail). Use the included zip ties and zip
tie mounts to secure the wiring to the body in the locations indicated. The
zip ties do not need to be tight; allow some extra length for wire movement.
H. INSTALL ROOF VISOR LIGHTS WIRING HARNESS
1. Remove the 2.6x6mm button-head cap screws (K) (3) from the roof visor
retainer (L). Remove the roof visor (M) and the retainer from the body
(refer to the Lighting Assembly Diagram for more detail).
2. Remove the 3x4mm set screws (N) (4) from the roof visor and remove
the visor lens (O) (2). Note orientation of the lens!
3. Feed the LED boards of the roof visor harness (P) through the hole in the
front right corner (passenger side) of the roof.
4. Install the LED boards in the visor lens; reinstall the lens in the roof visor.
Note orientation of the lens! Secure the lens with the 3x4mm set screws
(4) removed during disassembly.
5. Route the harness connecting the two circuit boards through the wire
retainers on the roof visor (Fig. 18).
6. Reinstall the roof visor and visor retainer using the 2.6x6mm button-
head cap screws removed during disassembly.
7. Secure the wiring to the visor retainer with the included zip ties (3)
(Fig. 19).
8. Remove the single green jumper from the circuit board on the roof lights
harness (if installed) (refer to the Body Wiring Diagrams on pages 6 & 7 for
more detail).
Fig. 14 Fig. 15
Fig. 13
Jumper
Plugs
Fig. 12
E. MODIFY THE BODY
The vehicle body will need modification
for visibility of the reverse light and rear
fog light on the rear bumper. Use Lexan®
body scissors or a hobby knife to cut out the
sections as indicated in Fig. 12. Follow the
lines molded into the body.
Fig. 19Fig. 19
Fig. 18Fig. 18
Fig. 16Fig. 16
Fig. 17Fig. 17
4
CAUTION:
RISK OF INJURY!
Use care with hobby knives, tapered
reamers, and other cutting tools as they
are extremely sharp and can cause severe
injury, deep cuts, and/or punctures.

I. INSTALL THE LIGHTING DISTRIBUTION BLOCK
1. Plug the yellow and green wires from the roof visor lights wiring harness into
the included high/low adapter. Plug the adapter into port M on the Lighting
Distribution Block .
2. Install the included single jumper into port E on the Lighting Distribution Block.
3. Plug all remaining LED light wire harness connectors into the ports on the
Lighting Distribution Block. Match the color band and/or letter indicator on
the wire harnesses with the corresponding color/letter of each port on the
distribution block (refer to the Lighting Distribution Block port chart below for
more detail).
4. Install the Lighting Distribution
Block mount (R) and secure with
the included 2.6x8 mm button-head
screws (2) as shown in Fig. 20.
5. Use the remaining 2.6x8mm
button-head screws (2) to secure
the Lighting Distribution Block to
the mount (Fig. 20).
6. Plug the breakaway cable from
the Lighting Distribution Block
into the connector on top of the
Power Module before installing the
vehicle body (Fig. 21).
Letter Color Description Function
B N/A Rear turn signal harness Rear turn signal LED
C Red Tail light harness Tail light and brake light LEDs
E Green Rear independent turn signal
jumper Install when using rear independent turn signals
G White Head light assembly harness Head lights, hood markers, and side marker light LEDs
H White Front turn signal harness Front turn signal LEDs
M N/A Roof light bar high/low harness LED light bar that mounts to roof of vehicle
LIGHTING DISTRIBUTION BLOCK LED LIGHT HARNESS PORTS
Breakaway Cable from
Lighting Distribution Block
Fig. 21Fig. 21
2.6x8mm BCS
2.6x8mm BCS
2.6x8mm BCS
2.6x8mm BCS
Fig. 20Fig. 20
2.6x6 BCS
A
BA
F
E
C
D
L
E
I
K
2.6x6 BCS
2.6x8 BCS
1.6x5 BCS
(self-tapping)
1.6x5 BCS
(self-tapping)
A
D
C
D
D
E
E
F
H
K
M
N
Q
P
B
O
G
R
G
H
J
LIGHTING ASSEMBLY DIAGRAM
2.6x8 BCS
2.6x8 BCS
J
5
PRO-SCALE
DISTRIBUTION
BLOCK
#XXXX
™
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Accessory Connectors
(not used with this kit) Wiring connectors for the
lights are labeled with
numbers and/or colors.

Rock
Light
Rock
Light
Motor
Chassis Wiring
(Top Down View)
(G 500® shown)
To Motor Connector
Receiver Communication Cable
To Motor Connector
To ESC
To Receiver
Motor Sense
Connectors
From ESC
From ESC
From CH2
Lighting
Power
Module
Rock
Light
Rock
Light
Rock
Light Rock Light
Rock
Light Rock Light
To ESC
Lighting
Power
Module
FRONT
Receiver Communication Cable
Black Wires to CH2
Blue Wire to CH1
Receiver
Route wires under
battery tray
Route wires under
battery tray
To MAXX Link
IN port on
Lighting Power
Module
From ESC
Optional MAXX Link
Cable Wiring
To Receiver
XL-5 HV ESC
Reverse LightFog Light
Headlight /
Turn Signal
Headlight /
Turn Signal
Body Wiring
(viewed from the
underside of the body)
Turn SignalTurn Signal
Tail Light /
Brake Light
Tail Light /
Brake Light
Breakaway Cable from
Distribution Block mounted on body
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
A
B
C
D
FRONT
Actual mounting view.
Distribution Block face shown
in the diagram for clarity.
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Jumper
Roof LightRoof Light
Side
Marker
Hood
Marker
Hood
Marker
Side
Marker
Disconnect jumper plugs for
Pro Scale Advanced Lighting
Control System use.
Breakaway Cable
to Lighting Power
Module on chassis
Remove stock jumper from board
for Pro Scale Advanced Lighting
Control System use.
Z
Z = Zip-tie Locations
Z
Z
Z
ZZ
Z
Z
Z
Z
G 500®BODY WIRING DIAGRAM
Visit Traxxas.com/ProScaleLighting for additional information.
6

Actual mounting view.
Distribution Block face shown
in the diagram for clarity.
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Rock
Light
Rock
Light
Motor
Chassis Wiring
(top down view)
To Motor Connector
Receiver Communication Cable
To Motor Connector
To ESC
To Receiver
Motor Sense
Connectors
From ESC
From ESC
From CH2
Lighting
Power
Module
Rock
Light
Rock
Light
Rock
Light Rock Light
Rock
Light
Rock
Light
Rock
Light
Rock
Light
To ESC
Lighting
Power
Module
FRONT
FRONT
Receiver Communication Cable
Black Wires to CH2
Blue Wire to CH1
Receiver
Route wires under
battery tray
Route wires under
battery tray
To MAXX Link
IN port on
Lighting Power
Module
From ESC
Optional MAXX Link
Cable Wiring
(TQi Receiver Only)
To Receiver
XL-5 HV ESC
Reverse LightFog Light
Jumper
Headlight /
Turn Signal
Roof LightRoof Light
Headlight /
Turn Signal
Side
Marker
Hood
Marker
Hood
Marker
Side
Marker
Disconnect jumper plugs for
Pro Scale Advanced Lighting
Control System use.
Turn SignalTurn Signal
Tail Light /
Brake Light
Tail Light /
Brake Light
Body Wiring
(viewed from the
underside of the body)
Remove stock jumper from board
for Pro Scale Advanced Lighting
Control System use.
Breakaway Cable from
Distribution Block mounted on body
E
F
G
H
K
M
N
A
B
C
D
Part 6593
PRO SCALE® LIGHTING
DISTRIBUTION BLOCK
Breakaway Cable
to Lighting Power
Module on chassis
Z
Z = Zip-tie Locations
Z
Z
Z
ZZ
Z
Z
Z
Z
G 63®BODY WIRING DIAGRAM
7

HEADLIGHTS MODE SELECTION
Use the Mode button on the Pro Scale Lighting Power Module to cycle through
the different lighting modes (from Low Beam Mode to High Beam Mode to
Daytime Mode).
HAZARD LIGHTS
Use the Signal button on the Pro Scale Lighting Power Module to turn the
hazard lights on or off.
TURN SIGNALS
The turn signals are activated by default. To deactivate the turn signals, press
and release the Signal button on the Pro Scale Lighting Power Module two
times quickly. Both left turn signal LEDs will blink once, and then both right turn
signals LEDs will blink once to indicate that the turn signals are deactivated.
To reactivate the turn signals: Press and release the Signal button two times
again quickly. Both left turn signal LEDs will blink twice, and then both right
turn signals LEDs will blink twice to indicate that the turn signals are activated.
TURN SIGNAL OPERATION
With the vehicle stopped, turn the steering wheel on the transmitter (left or
right) to turn on the LEDs. The turn signal LEDs will continue to flash while the
steering wheel is turned in this same direction or remains centered. Turn the
steering wheel in the opposite direction to cancel the turn signal.
LIGHTING CONTROL SYSTEM OPERATION
APPENDIX
Signal
Selection Action
Hazard Lights On Press and release Signal once
Hazard Lights O Press and release Signal once again
Deactivate Turn Signals Press and release Signal 2x quickly
Activate Turn Signals Press and release Signal 2x quickly again
Mode
Selection Action
Low Beam Headlights Default
High Beam Headlights Press and release Mode
Daytime Headlights (o) Press and release Mode once again
AUX
POWER
IN RX INOUT
Part 6592
1
2
3
4
5
6
7
8
9
10
11
12
MOTOR
SENSOR
MAXX LINK
SIGNAL
MODE
PRO SCALE® LIGHTING POWER MODULE
Mode SelectSignal Select
Warranty Information
Traxxas electronic components are warranted to be free from defects in materials and
workmanship for a period of 30 days from the date of purchase.
Limitations: Any and all warranty coverage does not cover replacement of
parts and components damaged by abuse, neglect, improper or unreasonable
use, crash damage, water or excessive moisture, chemical damage, improper or
infrequent maintenance, accident, unauthorized alteration or modification or items
that are considered consumable. Traxxas will not pay for the cost of shipping or
transportation of a defective component to us.
Traxxas Lifetime Electronics Warranty
After the expiration date of the warranty period, Traxxas will repair electronic components
for a flat rate. Please visit Traxxas.com/support for a current schedule of warranty costs and
fees. The covered repairs are limited to non-mechanical components that have NOT been
subjected to abuse, misuse, or neglect. Products damaged by intentional abuse, misuse, or
neglect may be subject to additional charges. Traxxas liability, in no case, shall be greater
than the actual purchase price of this product. For replacement, product must be returned
in brand new condition, with packaging and itemized sales receipt.
Download and install the latest rmware
updates, change the module settings, and gain
access to additional functions using the Traxxas
Link App (available in the Apple App StoreSM or
on Google Play™). The TQi transmitter with the
Traxxas Link Wireless Module (part #6511, sold
separately) are required.
This device complies with FCC Part 15 & IC RSS-210 rules subject
to the following conditions: 1) This device may not cause harmful
interference, and 2) This device must accept all interference received,
including interference that may cause undesired operation.
For patent and patent-pending information, please visit Traxxas.com/pat
App Store is a service mark of Apple Inc. Google Play is a trademark of Google Inc.
Mercedes-Benz®, G 500®, and G 63® are trademarks of Mercedes-Benz/Daimler AG.
All copyrights and trademarks are used by Traxxas under license.
WARRANTY
6V 50mA
CH1
CH2
Important: To prevent possible damage to the electronics while using an external BEC, do not connect both the MAXX Link Cable and Receiver
Communication Cable to the Lighting Power Module at the same time.
Lighting Power Module
ESC
Receiver
BEC Receiver
Communication
Cable
WIRING DIAGRAM WITH RECEIVER COMMUNICATION
CABLE AND HIGH-OUTPUT EXTERNAL BEC
(part #2262, sold separately)
6V 50mA
CH2
Lighting Power Module
ESC
Receiver
BEC
WIRING DIAGRAM WITH OPTIONAL MAXX®LINK CABLE
AND HIGH-OUTPUT EXTERNAL BEC
(part #2262, sold separately)
OPTIONAL MAXX LINK CABLE WIRING
Traxxas Link
Wireless Module
(part #6511, sold
separately) TQi Receiver
MAXX Link Cable
to Expansion Port
Servo wire to CH1
ESC wire to CH2
Plug the MAXX Link cable into the MAXX Link IN port on the Lighting Power Module.
Use the same wire routing from the Lighting Power Module and into the receiver box
as shown in the Receiver Communication Cable Installation instructions. Plug the
loose end of the cable into the expansion port on the receiver.
Use the optional included MAXX®Link
Cable to connect the Lighting Power
Module to the receiver. DO NOT use the
Receiver Communication Cable with
the MAXX Link Cable. The MAXX Link
Cable is designed to work with the Traxxas
Link™Wireless Module (part #6511, sold
separately) to provide Traxxas Link App
functionality for custom lighting controls
and configurations. Your model may
require a software update for the TQi
receiver via the Traxxas Link App (Traxxas
Link Wireless Module required).