Treasure Garden BF10 User manual

Assembly Guide
www.treasuregarden.com
©2020 Treasure Garden, Inc. - All Rights Reserved.
v.07.23.20
BF10 Resin Base Weights
CANTILEVER BASE
WARRANTY:
Treasure Garden warrants this product
(for residential use ONLY) to be free
from defects in original materials and
workmanship for a period of 1 year from
the date of purchase. If a defect in the
original material or workmanship appears
during the warranty period; Treasure
Garden will (at its discretion) repair or
replace the product without charge.
Simply contact your original authorized
Treasure Garden dealer with a description
of the defect. The dealer will verify the
defect and work closely with Treasure
Garden to obtain the necessary service.
In many cases, simple problems can
be solved with a replacement part that
can be shipped directly to the dealer for
professional installation / repair.
There are no serviceable parts within this
product. Tampering with or altering the
product will void warranty.
In the event that warranted factory service
is required, Treasure Garden will assume
the responsibility of the return freight
charges for the first year only.
Returned product that (upon receipt and
inspection) is deemed to be “not covered”
under our warranty, will be shipped / billed
at your expense.
This warranty gives you specific legal
rights, and you may have other rights
which vary from state to state.
RUST: Rust is a natural part of the aging
process of steel or iron based materials,
and is therefore NOT considered a defect.
NOTE: Failure caused by unreasonable or
abusive use, or failure caused by neglect
of reasonable and necessary care are not
covered by this warranty.
Additionally, acts of nature (including but
not limited to wind, hurricanes, tornadoes,
and storms) are not covered by this
warranty.

Thank you for purchasing Treasure Garden’s Cantilever Base.
Please remove all contents from the package, inspect and review checklist.
CHECKLIST
A - (1) Resin Base Weights
B- 220 lbs. All-Purpose Sand (not included)
21
CAUTION: Fully assembled, the umbrella weighs approximately 300 lbs. Moving the
umbrella fully assembled will increase the risk of damage to your umbrella and/or can
cause serious injury. We recommend a two-person team for assembly and disassembly.
A - B -
IMPORTANT:
• AG Universal Cross Bar Stand will not support umbrella without proper weight. Using
the cross bar stand without weight will damage your umbrella and may cause injury.
DO NOT OPEN UMBRELLA UNTIL WEIGHTS ARE SECURED.
• Prior to assembly it is important to decide on the location of the umbrella.
• Allow ample height to avoid damage to your umbrella during assembly and usage.
• Choose a location that is level and sturdy.
• Avoid any sloping or soft ground.
Note: Some parts may be included in the styrofoam packaging. DO NOT discard any
packaging or box until assembly is complete.
(Fig. 1)
(Fig. 3)(Fig. 2)
220 lbs.
STEP 1FILL BASE WEIGHTS
• Remove 4 resin base weights from packaging and lay on soft surface (Fig. 1).
• Remove caps from each resin base weight by turning counter clockwise (Fig. 2) and fill
with all purpose sand (Fig. 3).
• Remove/clean any excess sand from base weight cap and threads. Secure cap on
container by turning clockwise.
Note:
• Each resin base weight holds up to 55 lbs. of sand, 220 lbs. for all 4.
STEP 2ASSEMBLE BASE
• Select area to set assembled AG Universal Cross Base Stand.
• Be sure bottom pole stem is attached to cross bar stand and cross bars are adjusted to
20” position. (Please refer to umbrella manual for instructions.)
• Place each resin base weight onto AG Universal Cross Bar Stand (Fig. 4).
• Hook each section together so the resin base weights are secured in place (Fig. 5).
• Begin with middle sections first (Fig. 5) and work your way out (Fig. 6).
• Your base is now ready for umbrella installation. Please refer to umbrella manual for
installation instructions.
(Fig. 5)(Fig. 4) (Fig. 6)
SAFETY PRECAUTIONS
• Handle base weights with care.
• Do not allow children to play on or with the base.
• Close and store the umbrella in windy conditions or when a storm approaches.
Never allow the umbrella to flap in the wind; this could damage the umbrella and
canopy.
• Do not leave open umbrella unattended.
• When adjusting the umbrella, make sure that no person(s) or item(s) are close to the
umbrella. This is important to prevent injury or material damage.

Thank you for purchasing Treasure Garden’s Cantilever Base.
Please remove all contents from the package, inspect and review checklist.
CHECKLIST
A - (1) Resin Base Weights
B- 220 lbs. All-Purpose Sand (not included)
21
CAUTION: Fully assembled, the umbrella weighs approximately 300 lbs. Moving the
umbrella fully assembled will increase the risk of damage to your umbrella and/or can
cause serious injury. We recommend a two-person team for assembly and disassembly.
A - B -
IMPORTANT:
• AG Universal Cross Bar Stand will not support umbrella without proper weight. Using
the cross bar stand without weight will damage your umbrella and may cause injury.
DO NOT OPEN UMBRELLA UNTIL WEIGHTS ARE SECURED.
• Prior to assembly it is important to decide on the location of the umbrella.
• Allow ample height to avoid damage to your umbrella during assembly and usage.
• Choose a location that is level and sturdy.
• Avoid any sloping or soft ground.
Note: Some parts may be included in the styrofoam packaging. DO NOT discard any
packaging or box until assembly is complete.
(Fig. 1)
(Fig. 3)(Fig. 2)
220 lbs.
STEP 1FILL BASE WEIGHTS
• Remove 4 resin base weights from packaging and lay on soft surface (Fig. 1).
• Remove caps from each resin base weight by turning counter clockwise (Fig. 2) and fill
with all purpose sand (Fig. 3).
• Remove/clean any excess sand from base weight cap and threads. Secure cap on
container by turning clockwise.
Note:
• Each resin base weight holds up to 55 lbs. of sand, 220 lbs. for all 4.
STEP 2ASSEMBLE BASE
• Select area to set assembled AG Universal Cross Base Stand.
• Be sure bottom pole stem is attached to cross bar stand and cross bars are adjusted to
20” position. (Please refer to umbrella manual for instructions.)
• Place each resin base weight onto AG Universal Cross Bar Stand (Fig. 4).
• Hook each section together so the resin base weights are secured in place (Fig. 5).
• Begin with middle sections first (Fig. 5) and work your way out (Fig. 6).
• Your base is now ready for umbrella installation. Please refer to umbrella manual for
installation instructions.
(Fig. 5)(Fig. 4) (Fig. 6)
SAFETY PRECAUTIONS
• Handle base weights with care.
• Do not allow children to play on or with the base.
• Close and store the umbrella in windy conditions or when a storm approaches.
Never allow the umbrella to flap in the wind; this could damage the umbrella and
canopy.
• Do not leave open umbrella unattended.
• When adjusting the umbrella, make sure that no person(s) or item(s) are close to the
umbrella. This is important to prevent injury or material damage.

Assembly Guide
www.treasuregarden.com
©2020 Treasure Garden, Inc. - All Rights Reserved.
v.07.23.20
BF10 Resin Base Weights
CANTILEVER BASE
WARRANTY:
Treasure Garden warrants this product
(for residential use ONLY) to be free
from defects in original materials and
workmanship for a period of 1 year from
the date of purchase. If a defect in the
original material or workmanship appears
during the warranty period; Treasure
Garden will (at its discretion) repair or
replace the product without charge.
Simply contact your original authorized
Treasure Garden dealer with a description
of the defect. The dealer will verify the
defect and work closely with Treasure
Garden to obtain the necessary service.
In many cases, simple problems can
be solved with a replacement part that
can be shipped directly to the dealer for
professional installation / repair.
There are no serviceable parts within this
product. Tampering with or altering the
product will void warranty.
In the event that warranted factory service
is required, Treasure Garden will assume
the responsibility of the return freight
charges for the first year only.
Returned product that (upon receipt and
inspection) is deemed to be “not covered”
under our warranty, will be shipped / billed
at your expense.
This warranty gives you specific legal
rights, and you may have other rights
which vary from state to state.
RUST: Rust is a natural part of the aging
process of steel or iron based materials,
and is therefore NOT considered a defect.
NOTE: Failure caused by unreasonable or
abusive use, or failure caused by neglect
of reasonable and necessary care are not
covered by this warranty.
Additionally, acts of nature (including but
not limited to wind, hurricanes, tornadoes,
and storms) are not covered by this
warranty.