TRENDnet TV-IP121W User manual

Quick Installation Guide
TV-IP121W
H/W: A1

Table of Contents
English ...................................................................................................... 1
1
4
3
9
1. Before You Start
2. Hardware Installation .........................................................................
3. Configure the Internet Camera ..........................................................
.................................................................................
Table of Contents
Version 05.13.2009
Troubleshooting ........................................................................................

System Requirements
Package Contents
1. Before You Start
English
1
?
?Utility CD-ROM
?Multi-Language Quick Installation
Guide
?1 x 2dBi DetachableAntenna
?AC PowerAdapter (5V, 2.5A)
?Camera
?RJ-45 Cable
TV-IP121W
Stand
?
?
?CPU: 350MHz or above / 800MHz (Windows Vista)
?Memory: 256MB RAM or above / 512MB RAM or above (Windows Vista)
?Windows 2000/XP/Vista
?VGAResolution: 800 x 600 or above
?Web Browser: Internet Explorer (6.0 or higher)
?Wireless Router orAccess Point
?AnAvailable DHCPServer –routers usually have a built-in DHCP server
10/100Mbps EthernetAdapter
CD-ROM Drive

54Mbps
SecurView Wireless Day/Night
Internet Camera
(TV-IP121W)
Wireless G Firewall Router
(TEW-432BRP) Modem
Notebook with Wireless G PC Card
(TEW-421PC)
Internet
English
2
Application

2. Hardware Installation
English
3
3. Connect theAC PowerAdapter to
the IP Camera and then to a power
outlet.
2. Connect a RJ-45 network cable
from a Switch/Router to the
Ethernet port on the IP Camera.
1. Attach the Antenna.
4. Verify the Power and Link LEDs
are on.

English
4
3. Configure the Internet Camera
Note:
1. It is recommended that you configure the IP Camera from a wired computer.
2. If you would like to use SecurView software, please refer to the User's Guide
on the CD for more information.
2. Follow the Installation Wizard
instructions and then click Close.
3. Go to Start -> Programs ->
TRENDnet -> IPSetup and click
IPSetup.
1. Insert the Utility CD-ROM into your
CD-ROM drive and then click
IP Setup.
Note: By default, the IP setting on theTV-IP121W is set to DHCP. Please
skip to step 8. If you want to give the TV-IP121W a static IP address, continue
on to step 4.

English
5
4. Select the IP camera and click
Change IP.
5. Configure the IP address to be in
the same subnet as your network,
type in the Administrator ID and
Password and click Change.
By default:
ID: admin
Password: admin
6. Click OK and wait 30 seconds.
7. Click OK.

11. Click Install.
English
6
9. Enter the User name and
Password, and then click OK.
By default:
User Name: admin
Password: admin
8. Double click the IP camera to
access the browser configuration.
10. Right click on the Internet
Explorer Information Bar and
select Install ActiveX Control.

14. Disconnect the RJ-45 cable and
unplug the power.Then plug the
power back in.
English
7
13. Click Site Survey. Select your
wireless network. If encryption
is enabled, select the proper
Authentication type, enter the
Pre-Shared Key and then click
Apply. (Example shows
WPA2-PSK. If your wireless
network does not support WPA,
select open or shared instead.
Contact your network
administrator for more
Note: The TV-IP121W will not work wirelessly until you disconnect the Ethernet
cable from the back of the camera.
12. Click Setup, Network and then
click Wireless.

16. Click Live View.
English
8
Your installation is now complete.
Note: For detailed information regarding the TV-IP121W configuration and
advanced settings, please refer to the Troubleshooting section, User's Guide
on the Utility CD-ROM, or TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
15. Verify the Power and Link LEDs
are on.