TRENDnet TV-IP600W - Wireless Pan/Tilt/Zoom Internet Camera Server... User manual

TV-IP600
TV-IP600W
H/W: V1
Quick Installation Guide

Table of Contents
Table of Contents
English ....................................................................................................... 1
1
3
9
1. Before You Start
2. Hardware Installation and Configuration .............................................
.................................................................................
Troubleshooting ..........................................................................................
Version 03.25.2009

System Requirements
Package Contents
1. Before You Start
1
?
?CD-ROM Drive
?
?
?
?
?Wireless router or access point (TV-IP600W)
?An available DHCP Server –routers usually have a built-in DHCP server.
10/100Mbps Ethernet Adapter
CPU: 2GHz processor or above
Memory: 256MB RAM or above / 512MB RAM or above (Windows Vista)
VGA Resolution: 800 x 600 or above
Web Brower: Internet Explorer (6.0 or higher)
English
?
?Utility CD-ROM
?Multi-Language Quick Installation
Guide
?1 x 2dbi Detachable Antenna
?
?Mounting Kit
?AC Power Adapter (5V, 2.5A)
TV-IP600/TV-IP600W
RJ-45 Cable

Application
2
English
Pan/Tilt/Zoom Internet Camera Server
(TV-IP600)
Wireless Pan/Tilt/Zoom
Internet Camera Server
(TV-IP600W)
300Mbps Wireless N
Gigabit Router
(TEW-639GR)
Internet
Wireless Pan/Tilt/Zoom
Internet Camera Server
(TV-IP600W)
300Mbps Wireless N
Gigabit Router
(TEW-639GR)
Internet
Pan/Tilt/Zoom Internet
Camera Server
(TV-IP600)
Wireless Pan/Tilt/Zoom Internet Camera Server
(TV-IP600W)
Pan/Tilt/Zoom Internet
Camera Server
(TV-IP600)

2. Hardware Installation and Configuration
3
2. Click Run autorun.exe
(Windows Vista only)
3. Click Setup Winzard.
1. Insert the Utility CD-ROM into your
CD-ROM drive.
Note:
1. It is recommended that you configure the IP Camera from a wired computer.
2. If you would like to use IPViewPro 2.0 software, please install the software
by clicking the Install IPView Pro 2.0 in the Autorun window and refer to the
User's Guide on the CD for more information.
4. Click Next. Then follow the Setup
Wizard instructions.
English

4
7. Attach the antennas to the IP
camera.
8. Connect a RJ-45 network cable
from a Switch/Router to the
Ethernet port on the IP Camera.
9. Connect the AC Power Adapter to
the IP Camera and then to a power
outlet.
6. Double click on the SetupWizard
icon on your desktop.
5. Click Close.
10. Click Next.
English

5
11. Select the IP camera and click
Next.
14. Select DHCP and then click Next.
15. Click I want to use wireless for
the camera and then click Next.
12. Enter your ID and password.
Then click Next. By default:
ID: admin
Password: admin
13. If you would like to change the
administrator password, click
Change Password, enter a new
password, retype the new
password and then click Next.
Leave Change Password
unchecked if you do not wish to
change the password.
Note: Password is limited to up to
8 characters.
English
Note: If you have the TV-IP600, please skip to step 18. If you have the
TV-IP600W, continue on to step 15.

6
19. Click Next.
20. Please wait while the settings on
your cameras are being saved.
English
16. Click Manually Setup Wireless
and then click Next.
18. Configure the Camera Name and
Camera Time. Click Copy
Local Time to automatically
configure the Camera Time to
match your computer. Then click
Next.
17. Select your wireless network from
the Available AP dropdown list.
If your wireless network does not
appear, manually enter the SSID
of your wireless network. If you
have Encryption enabled, select
the Authentication, select the
Encryption and enter your Key.
Then click Next.

7
21. Disconnect the RJ-45 cable and
unplug the power. Then plug the
power back in. Wait about 30
seconds while the IP Camera
reboots. Then verify the PWR
and LNK LEDs are on.
22. Click on the following URL or click
Link to open up the browser
configuration.
23. Enter the User name and
Password, and then click OK. By
default:
User Name: admin
Password: admin
English
Note: The TV-IP600W will not work wirelessly until you disconnect the Ethernet
cable from the back of the camera.
24. Click View Video | ActiveX or
View Video | Java to view live
video.

28. Use the command icons to control
the camera.
English
8
Your installation is now complete.
Note: For detailed information regarding the TV-IP600/TV-IP600W configuration
and advanced settings, please refer to the Troubleshooting section, User's Guide
on the Utility CD-ROM, or TRENDnet's website at http://www.trendnet.com.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
26. Click Install (ActiveX.only).
25. Right click on the yellow bar and
select Install ActiveX Control
(ActiveX.only).
27. Live Video will now appear.