TRENDnet TV-IP100-N User manual

TV-IP100-N
TV-IP100W-N
H/W: 1.0 R
Quick Installation Guide

Table of Contents
English ...................................................................................................... 1
1
4
3
1. Before You Start
2. Hardware Installation .........................................................................
3. Configure the Internet Camera ..........................................................
.................................................................................
Table of Contents
Version 03.04.2008
8
Português
Para Guia de Instalação em Português, favor ver CD.
Troubleshooting ........................................................................................
Eesti
Eestikeelse paigaldusjuhendi leiate kaasasolevalt CD-plaadilt.

System Requirements
Package Contents
1. Before You Start
English
1
?
?
?Quick Installation Guide
?1 x 2dBi Detachable Antenna
(TV-IP100W-N
?AC Power Adapter (5V, 2.5A)
?Camera Mounting Stand
TV-IP100-N/TV-IP100W-N
Utility CD-ROM
)
?
?Wireless router or wireless access point (TV-IP100W-N)
?
?
?
?
10/100Mbps Ethernet
CPU: 1GHz processor or above
Memory: 256MB RAM or above/ 512MB RAM or above (Windows Vista)
VGA Resolution: 800 x 600 or above
Web Brower: Internet Exploreer (6.0 or higher)

Application
English
2
Wireless N Gigabit Router
(TEW-633GR)
Cable/DSL Modem
Internet
Parking Monitoring
(TV-IP100W-N)
Warehouse Monitoring
(TV-IP100W-N)
Office Monitoring
(TV-IP100-N)
Front Gate
(TV-IP100-N)
Monitoring
Office Monitoring
(TV-IP100-N)
Parking Monitoring
(TV-IP100W-N)
Wireless N Gigabit Router
(TEW-633GR)
Cable/DSL Modem
Internet
Front Gate Monitoring
(TV-IP100-N)
Warehouse
(TV-IP100W-N)
Monitoring

2. Hardware Installation
English
3
4. Verify the Power and Link LEDs
are on.
1. Connect a RJ-45 network cable
from a Switch/Router to the
Ethernet port of the Internet
Camera Server.
2. Attach the Antenna.
(TV-IP100W-N)
3. Connect the AC Power Adapter to
the Internet Camera Server and
then to a power outlet.

English
4
3. Configure the Internet Camera
Note: It is recommended that you configure the Internet Camera from a wired
computer. Since the Internet Camera's default IP address is 192.168.10.30,
make sure no other network devices are assigned an IP address of
192.168.10.30.
2. Follow the Installation Wizard
instructions and then click Finish.
3. Go to Start -> Programs ->
TRENDnet -> Setup Wizard and
click Setup Wizard.
4. Select the Internet Camera and
click Wizard.
For Windows Users
1. Insert the Utility CD-ROM into your
CD-ROM drive and then click
Setup Wizard.

English
5
5. Enter the Admin ID and Password,
and then click OK. By default:
Admin ID: admin
Password: admin
If you like to change the Admin ID
and password, click Change, enter
the New ID and the New Password
and confirm the New ID and New
Password. Then click on the right
arrow.
6. Click the right arrow. If you have
the TV-IP100-N skip to step 9. If
you have the TV-IP100W-N
continue on to step 7.
7. Enter the Network Name (SSID) of
your wireless network. If
encryption is enabled on your
wireless network, select the
desired Security Mode. If WEP is
enabled on your wireless network,
select Open, Shared or Both.
Then click the right arrow.
If no encryption is enable skip to
step 9.

9. Copy down the IP Address. Then
click the reboot button to save
settings.
10. Disconnect the RJ-45 cable and
unplug the power. Then plug the
power back in (TV-IP100W-N).
English
6
8. If WEP is enabled on your wireless
network, select the Encryption
Mode (e.g. 64-bit, 128-bit), the Key
Format (e.g. Hex, ASCII) and the
Default Key (e.g. Key_1, Key_2,
Key_3, Key_4). Then enter the
encryption key in the Key1, Key2,
Key3 or Key 4 field. Then click the
right arrow.
If WPA is enabled on your wireless
network, enter the encryption key
in the Pre-Shared Key field and
then click the right arrow button to
continue.
Note: If you do not know your
encryption key, contact your
network administrator for more
information
Note: The TV-IP100W-N will not work wirelessly until you disconnect the
Ethernet cable from the back of the camera.

English
7
14. If you clicked on View Video |
Active X, right click and select
Active X Control.
11. Verify the Power and Link LEDs
are on.
12. In the Setup Wizard, click Link.
13. Click View Video | Active X or
View Video | Java.
Your installation is now complete.
15. Click Install.
Note: For detailed information regarding the TV-IP100-N/IP100W-N
configuration and advanced settings, please refer to the Troubleshooting
section, User's Guide on the Utility CD-ROM, or TRENDnet's website at
http://www.trendnet.com.

Q1:
A1:
Q2:
A2:
Q3:
A3:
Q4:
A4:
Q5:
A5:
Q6:
A6:
The setup wizard is unable to detect my camera. What should I do?
First, verify that you have followed all the steps in the Section 2: Hardware Installation.
Second, disable any software firewall programs such as ZoneAlarm or Norton Internet
Security. If you are using Windows XP or Windows Vista, disable the built in firewall. Third,
click on Search in the setup wizard.
When I click on View Image | Active X mode or View Image | Java Mode, the image does
not load. What should I do?
First, make sure that you are using a browser that supports Active X or Java. Second,
make sure that Active X or Java is installed and enabled.
How do I connect the TV-IP100W-N to my wireless router or access point?
Make sure that you configure the camera to have the same SSID, encryption mode and
key (if enabled). Follow the instructions in section 2 to configure the camera with the SSID
and encryption key.
After I successfully configured the TV-IP100W-N to match my wireless network settings,
I can not connect to the camera.
First, verify that the wireless settings match your wireless network settings. Second,
verify in the wireless section of the browser configuration that the Enable option is checked.
Third, make sure to disconnect the Ethernet cable from the camera and verify that the LINK
LED is blinking red.
I setup a password on the camera, but I forgot it. What should I do?
Take a pin or paperclip and press the reset button on the back of the unit for 15 seconds.
This will return settings back to factory defaults. The default IP address is 192.168.10.30.
By default, the Admin ID and Password is admin.
If you still encounter problems or have any questions regarding the TV-IP100-N/TV-IP100W-N,
please contact TRENDnet’s Technical Support Department.
The Image is blurry. How can I adjust the focus on the Internet camera?
You can adjust the Internet Camera’s focus by rotating the lens.
8
Troubleshooting