TRENDnet TE100-DX4PCI User manual

Ethernet Card for PCI
1
TE100-DX4PCI
10/100 Mbps
Fast Ethernet Hub Card
for PCI
Auto-Congurable
User's Guide

Ethernet Card forPCI
2
FCC Compliance Statement
This device complies with Part 15 of the FCC rules. Operation
is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
NOTE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
This Class B digital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Requlations.
Cet appareil numérique de la Classe B respecte toutes
les exigences du Réglement sur le matériel brouilleur du
Canada.
All registered trademarks are the property of their respective

Ethernet Card for PCI
3
CONTENTS
FCC Compliance Statement ........................ 1
Section 1 Introduction .................................... 4
Section 2 Installation ..................................... 5
Section 3 Conguration and Diagnostics .... 6
Section 4 Drivers Installation ...................... 7
Section 5 Cable Specications ..................... 8
Section 6 Troubleshooting ............................. 9
Section 7 Specications ................................. 10
Section 8 LED Indication ............................... 11

Ethernet Card forPCI
4
Section 1 Introduction
Your Ethernet hub card is a high performance network
device that is designed to easily link four 10/100Mbps
hub with a 100Mbps PCI interface card. The hub
card
consists of four (4) 10/100BASE-TX hub port to
linking and forwartding packets in one segment, it also
includes a 32-bit PCI interface to provide an additional
connection with the network segment.
The Ethernet hub card is designed for plug-and-play
installation and easy managements with all
10/100Mbps ports and LEDs on the bracket.
Summary of features
• Compliant with the 10BASE-T, 100BASE-TX
specication of the IEEE 802.3 standard
• All 10/100Mbps hub port supports auto-negotia
tion and ato-detection for 10 or 100Mbps
• Equipped with four LEDs for easy viewing and
troubleshooting
• Equipped with a 100Mbps MAC interface to pro
vides a connection with the 10/100Mbps
hub seg ment
• Diagnostic software and network drivers on the
diskette
• 32-bit bus mastering for high throughput and
low
processor utilization

Ethernet Card for PCI
5
Section 2 Installation
This section describes how to install your Ethernet
hub card. Perform the following steps to install the
adapter.
1. Turn off your computer and all peripherals.
2. Make a note of the cables and cords that are
connected to the computer and disconnect them.
3. Remove your personal computer's cover (refer to
the owner's manual of your personal computer).
4. Select any available PCI slot, and remove the
slot cover.
5. Carefully install the Ethernet hub card into the
ex-pansion slot by rmly pressing the card into
the edge of the connector slot until the card is
snugly seated in the expansion slot and fasten
the retaining bracket with screw from the slot
cover.
6. Reinstall your personal computer's cover and
re-connect the power cord and all cables.
7. Connect the Ethernet cable to your personal
computer.
Note:
System Requirements:
A PC and BIOS that support the PCI Local Bus

Ethernet Card forPCI
6
Specication 2.x.
Section 3 Conguration and Diagnostics
Your Ethernet hub card has built-in a 100Mbps MAC
interface which is automatically configured when
you power-up your computer, In certain computers,
however, you must modify your BIOS by entering
your CMOS SETUP utility.
To view the configuration parameters assigned by
the BIOS, boot the computer to DOS, insert the
diskette into the oppy drive and then execute the utility
software EZRTS.EXE in the CONFIG directory.

Ethernet Card for PCI
7
Section 4 Drivers Installation
Be sure to install the proper driver for the hub card
to provides a connection between the 100Mbps MAC
interface and the four 10/100Mbps nodes.
You can use the drivers supplied by the software
diskette that is compatible with your Networking
Operating System. The driver for each Networking
Operating System is under a separate directory. Each
directory includes a README.TXT le to describe
the detailed installation procedure. A RELEASE.TXT
le under root directory lists the information of all
the available drivers.

Ethernet Card forPCI
8
Section 5 Cable Specications
The Ethernet adapter is equipped with four
RJ-45 connectors, the RJ-45 connector requires a
corrsponding cable. This section describes each
cable's specication.
• Cable for RJ-45 connector for 10Mbps network
Cable type: UTP with 2
twisted pairs o f
22, 24 or 26 AWG
Category: 3, 4, or 5
Twists per foot: 2 to 3(min.)
Nominal impedance: 100 ohms
Maximum cable length: 300'(100m)
Maximum Attenuation: 8 to 10 dB per 100m
at 10Mz
• Cable for RJ-45 connector for 100Mbps network
Cable type: UTP with 2
twisted pairs of 2 6
AWG
Category: 5
Twists per foot: 2 to 3(min.)
Nominal impedance: 100 ohms
M20082217500

Ethernet Card for PCI
9
Maximum cable length: 300'(100m)
Section 6 Troubleshooting
This section describes reasons for some adapter's
failures
and the actions to be taken to resolve the problems.
• PCI scan specied, device not found
Action: Verify that the PCI Ethernet adapter is
physically installed properly. Otherwise,
install the card in a different PCI
slot or replace the adapter.
• Connection failure if using an unshielded twisted
M20082217500

Ethernet Card forPCI
10
pair (UTP) cable
Action: Verify that the UTP cable
is rmly attached
and the cable type is correct for use.
Section 7 Specications
IEEE 802.3 Standard: 10BASE-T
100BASE-TX
Wiring Connector: RJ-45
Bus Characteristics: 32 bits ; PCI Local Bus
specication 2.x
I/O address: being assigned by the
BIOS to a free I/O address
block
IRQ line: INTA ; being assigned
by the BIOS to a free IRQ
(interrupt) number