TRENDnet TEG-448WS - Switch User manual

FCC Warning
This equipment has been tested and found to comply with the
regulations for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and radiates
radio frequency energy. If not installed and used in accordance with
the instructions, it may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be
required to correct the interference at the user’s expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be required
to take adequate measures.
VCCI Warning
This is a product of VCCI Class A Compliance.

UL Warning
a) Elevated Operating Ambient Temperature- If installed in a closed
or multi-unit rack assembly, the operating ambient temperature of the
rack environment may be greater than room ambient. Therefore,
consideration should be given to installing the equipment in an
environment compatible with the manufacturer's maximum rated
ambient temperature (Tmra).
b) Reduced Air Flow- Installation of the equipment in a rack should
be such that the amount of air flow required for safe operation of the
equipment is not compromised.
c) Mechanical Loading- mounting of the equipment in the rack
should be such that a hazardous condition is not achieved due to
uneven mechanical loading.
d) Circuit Overloading- Consideration should be given to the
connection of the equipment to the supply circuit and the effect that
overloading of circuits might have on current protection and supply
wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
e) Reliable Grounding- Reliable grounding of rack mounted
equipment should be maintained. Particular attention should be given
to supply connections other than direct connections to the branch
circuit (e.g., use of power strips).
Ver. 1.00

i
TABLE OF CONTENT
About This Guide.................................................................................1
Purpose ............................................................................................1
Terms/Usage....................................................................................1
Introduction..........................................................................................2
Gigabit Ethernet Technology...........................................................2
Fast Ethernet Technology ................................................................3
Switching Technology .....................................................................4
VLAN (Virtual Local Area Network)..............................................5
Features............................................................................................5
package Contents and Installation........................................................7
Package Contents.............................................................................7
Installation .......................................................................................7
Rack Mounting ................................................................................8
Connecting Network Cable..............................................................9
AC Power.........................................................................................9
Identifying External Components......................................................10
Front Panel.....................................................................................10
Rear Panel......................................................................................11
Understanding LED Indicators ..........................................................12
Power and System LEDs ...............................................................12
Ports 1~48 Status LEDs.................................................................13
mini-GBIC 45F~48F Status LEDs.................................................13
Configuration.....................................................................................14
ii
Installing the Web Management Utility.........................................14
Discovery List................................................................................15
Monitor List...................................................................................16
Device Setting................................................................................18
Toolbar...........................................................................................19
Configuring the Switch..................................................................20
Login..............................................................................................20
Configuration Menu.......................................................................22
Configuring Setup Settings............................................................23
Port Settings...............................................................................23
VLAN Settings (IEEE 802.1Q VLAN) .....................................26
Trunk Setting .............................................................................38
Mirror Setting.............................................................................38
IEEE 802.1p Default Priority.....................................................40
Broadcast Storm Control Setting ...............................................41
Jumbo Frame Setting .................................................................41
Advanced Setting...........................................................................42
IGMP Global Setting .................................................................42
IGMP VLAN Setting.................................................................44
System Settings..............................................................................46
System Information....................................................................46
System Setting ...........................................................................46
Trap Setting................................................................................47
Password Setting........................................................................49
Statistics.....................................................................................49

iii
Factory Reset .............................................................................51
Backup Setting...........................................................................51
Firmware Upload.......................................................................52
System Reboot...........................................................................52
Logout............................................................................................53
Technical Specifications....................................................................54

1
ABOUT THIS GUIDE
Congratulations on your purchase of the TEG-448WS 48-Port Gigabit
Ethernet Web Smart Switch. This device integrates 1000Mbps Gigabit
Ethernet, 100Mbps Fast Ethernet and 10Mbps Ethernet network
capabilities in a highly flexible package.
Purpose
This guide describes how to install your TEG-448WS 48-Port Gigabit
Ethernet Web Smart Switch.
Terms/Usage
In this guide, the term “Switch” (first letter upper case) refers to the
device of TEG-448WS 48-Port Gigabit Ethernet Web Smart Switch
and “switch” (first letter lower case) refers to other Ethernet switches.
2
INTRODUCTION
This chapter describes the features of the TEG-448WS 48-Port
Gigabit Ethernet Web Smart Switch and some background
information about Ethernet/Fast Ethernet/Gigabit Ethernet switching
technology.
Gigabit Ethernet Technology
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the
same packet structure, format, and support for CSMA/CD protocol,
full duplex, flow control, and management objects, but with a tenfold
increase in theoretical throughput over 100-Mbps Fast Ethernet and a
hundredfold increase over 10-Mbps Ethernet. Since it is compatible
with all 10-Mbps and 100-Mbps Ethernet environments, Gigabit
Ethernet provides a straightforward upgrade without wasting a
company’s existing investment in hardware, software, and trained
personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet
is essential to coping with the network bottlenecks that frequently
develop as computers and their busses get faster and more users use
applications that generate more traffic. Upgrading key components,
such as your backbone and servers to Gigabit Ethernet can greatly
improve network response times as well as significantly speed up the
traffic between your subnets.
Gigabit Ethernet enables fast optical fiber connections to support
video conferencing, complex imaging, and similar data-intensive
applications. Likewise, since data transfers occur 10 times faster than
Fast Ethernet, servers outfitted with Gigabit Ethernet Adapters are
able to perform 10 times the number of operations in the same amount
of time.

3
In addition, the phenomenal bandwidth delivered by Gigabit Ethernet
is the most cost-effective method to take advantage of today and
tomorrow’s rapidly improving switching and routing internetworking
technologies. And with expected advances in the coming years in
silicon technology and digital signal processing that will enable
Gigabit Ethernet to eventually operate over unshielded twisted-pair
(UTP) cabling, outfitting your network with a powerful 1000-Mbps-
capable backbone/server connection creates a flexible foundation for
the next generation of network technology products.
Fast Ethernet Technology
The growing importance of LANs and the increasing complexity of
desktop computing applications are fueling the need for high
performance networks. A number of high-speed LAN technologies
have been proposed to provide greater bandwidth and improve
client/server response times. Among them, 100BASE-T (Fast
Ethernet) provides a non-disruptive, smooth evolution from the
current 10BASE-T technology. The non-disruptive and smooth
evolution nature, and the dominating potential market base, virtually
guarantees cost-effective and high performance Fast Ethernet
solutions.
100Mbps Fast Ethernet is a standard specified by the IEEE 802.3
LAN committee. It is an extension of the 10Mbps Ethernet standard
with the ability to transmit and receive data at 100Mbps, while
maintaining the CSMA/CD Ethernet protocol. Since the 100Mbps
Fast Ethernet is compatible with all other 10Mbps Ethernet
environments, it provides a straightforward upgrade and takes
advantage of the existing investment in hardware, software, and
personnel training.
4
Switching Technology
Another approach to pushing beyond the limits of Ethernet technology
is the development of switching technology. A switch bridges
Ethernet packets at the MAC address level of the Ethernet protocol
transmitting among connected Ethernet or Fast Ethernet LAN
segments.
Switching is a cost-effective way of increasing the total network
capacity available to users on a local area network. A switch increases
capacity and decreases network loading by dividing a local area
network into different segments, which don’t compete with each other
for network transmission capacity.
The switch acts as a high-speed selective bridge between the
individual segments. The switch, without interfering with any other
segments, automatically forwards traffic that needs to go from one
segment to another. By doing this the total network capacity is
multiplied, while still maintaining the same network cabling and
adapter cards.
Switching LAN technology is a marked improvement over the
previous generation of network bridges, which were characterized by
higher latencies. Routers have also been used to segment local area
networks, but the cost of a router, the setup and maintenance required
make routers relatively impractical. Today switches are an ideal
solution to most kinds of local area network congestion problems.

5
VLAN (Virtual Local Area Network)
A VLAN is a group of end-stations that are not constrained by their
physical location and can communicate as if a common broadcast
domain, a LAN. The primary utility of using VLAN is to reduce
latency and need for routers, using faster switching instead. Other
VLAN utility includes:
Security, Security is increased with the reduction of opportunity in
eavesdropping on a broadcast network because data will be switched
to only those confidential users within the VLAN.
Cost Reduction, VLANs can be used to create multiple broadcast
domains, thus eliminating the need of expensive routers.
Features
48×10/100/1000Mbps 1000BASE-T Auto-negotiation Gigabit
Ethernet ports
4 x 1000Mbps mini-GBIC slots for optional mini-GBIC
transceiver to extend distance, shared with 4 1000BASE-T ports
All RJ-45 ports support auto MDI/MDIX
Half duplex transfer mode for connection speed 10Mbps and
100Mbps
Full duplex transfer mode for connection speed of 10Mbps,
100Mbps and 1000Mbps
Store-and-Forward switching architecture to support rate
adaptation and ensure data integrity
Integrated address Look-Up Engine, supports 8K absolute MAC
addresses
1024KB RAM for data buffering
6
Supports IEEE 802.3x flow control for full-duplex mode ports
Supports IEEE 802.1Q VLAN
Supports IEEE 802.1p Priority Queues
Supports IGMP Snooping
Supports Static Port Trunk
Supports Jumbo Frame
Supports Broadcast Storm Control
Supports six Trunk groups.
Supports Port-mirroring
Supports Port-setting for Speed, Duplex and Flow control
Easy configuration via WEB Browser
Easy setup via Web Management Utility
Standard 19” Rack-mount size

7
PACKAGE CONTENTS AND INSTALLATION
This chapter provides Packaging Contents and installation information
for the Switch.
Package Contents
Open the box of the Switch and carefully unpacks its contents. The
packaging should contain the following items:
TEG-448WS 48-Port Gigabit Web-Based Smart Switch
Quick Installation Guide
CD-ROM (Utility & User’s Guide)
Power Cord
Rackmount Kit (Rubber Feet, Screws and Mounting Brackets)
If any item is found missing or damaged, please contact your local
reseller for replacement.
Installation
Install the Switch in a fairly cool and dry place. See Technical
Specifications for the acceptable temperature and humidity operating
ranges.
Install the Switch in a site free from strong electromagnetic field
generators (such as motors), vibration, dust, and direct exposure to
sunlight.
Leave at least 10cm of space at the front and rear of the hub for
ventilation.
8
Install the Switch on a sturdy, level surface that can support its weight,
or in an EIA standard-size equipment rack. For information on
rackmount installation, see the next section, Rack Mounting.
When installing the Switch on a level surface, attach the rubber feet to
the bottom of each device. The rubber feet cushion the hub and
protect the hub case from scratching.
Figure 1. Attach the adhesive rubber pads to the bottom
Rack Mounting
The switch can be mounted in an EIA standard-size, 19-inch rack,
which can be placed in a wiring closet with other equipment. Attach
the mounting brackets at the switch’s front panel (one on each side),
and secure them with the provided screws.
Figure 2. Combine the Switch with the provided screws

9
Then, use screws provided with the equipment rack to mount each
switch in the rack.
Figure 3. Mount the Switch in the rack
Connecting Network Cable
The Switch supports 10/100/1000Mbps Ethernet that runs in Auto-
negotiation mode, 10/100Mbps Ethernet that runs in half and full
duplex mode and 1000Mbps Gigabit Ethernet that runs in full duplex
mode using four pair of Category 5 Cable.
These RJ-45 ports are Auto-MDIX, allowing you to use either a
standard or crossover RJ-45 cable.
There are 4 additional mini-GBIC slots for optional mini-GBIC
modules.
AC Power
The Switch uses 100-240V AC, 50-60 Hz AC power. The switch’s
power supply will adjust to the local power source automatically and
may be turned on without having any Ethernet cables connected.
10
IDENTIFYING EXTERNAL COMPONENTS
This chapter describes the front panel, rear panel, and LED indicators
of the Switch.
Front Panel
The figure below shows the front panel of the Switch.
Figure 4. Front panel of 48-port Gigabit Ethernet Switch
LED Indicator:
Comprehensive LED indicators display the status of the switch and
the network (see the LED Indicators chapter below).
1000BASE-T Gigabit Ethernet Ports (Port 1~48):
The Switch has 48 auto-negotiation, auto-MDIX Gigabit ports.These ports
can operate in half-duplex mode for 10/100Mbps and full-duplex mode for
10/100/1000Mbps.
Note: When the port is set to “Forced Mode”, the Auto-MDIX will
be disabled.
mini-GBIC Ports (Port 45F~48F)
The Switch is equipped with four mini-GBIC ports. The ports
support optional 1000BASE-SX/LX mini-GBIC module.
Port 45, 46, 47 and 48 are shared with the mini-GBIC 45F, 46F, 47F
and 48F ports. When you plug in a mini-GBIC module, the device the
RJ-45 port will be disabled.
Reset:

11
The Reset button reset settings back to factory default.
Note: Please make sure you copy down or save settings before
pressing “Reset” button.
Rear Panel
The rear panel of the Switch consists of an AC power connector. The
following shows the rear panel of the Switch
Figure 5. Rear panel of the Switch
AC Power Connector:
Plug in the female connector of the provided power cord into this
connector. Connect the male into a power outlet. Supported input
voltages range from 100-240V AC at 50-60Hz.
12
UNDERSTANDING LED INDICATORS
The front panel LEDs provides instant status feedback for easy
monitoring and troubleshooting.
Figure 6. LED indicators of the Switch
Power and System LEDs
POWER: Power Indicator
On : When the Power LED is lit, the Switch is receiving power.
Off : When the Power LED is off, the switch is off.
System: Management Indicator
Blinking : When the Switch is working, the System LED blinks.
On/Off : The Switch is not working.

13
Ports 1~48 Status LEDs
Link/ACT: Link/Activity( left side of each RJ-45 port)
On Amber: When the Link/ACT LED lights green, the respective port is
successfully connected to a 10 Mbps Ethernet or 100Mbps Fast
Ethernet network.
Green: When the Link/ACT LED lights amber, the respective port is
successfully connected to a 1000Mbps Gigabit Ethernet network.
Blinking Amber: When the Link/ACT LED is blinking amber, the port is
transmitting or receiving data on the 10Mbps Ethernet or 100Mbps
Fast Ethernet network.
Green: When the Link/ACT LED is blinking amber, the port is
transmitting or receiving data on the 1000Mbps Gigabit Ethernet
network.
Off : No link.
mini-GBIC 45F~48F Status LEDs
Link/ACT
On : When the Link/ACT LED is lit, the port is successfully connected.
Blinking : When the Link/ACT LED is blinking, the port is transmitting or
receiving data on the Ethernet network.
Off : LC fiber cable is not connected or the mini-GBIC module is not
installed.
14
CONFIGURATION
You can configure the Switch settings such as VLAN, Trunking,
QoS… etc using the Web Browser.
The Web Management Utility allows the user to easily discover the
Web Management Switch, assign the IP Address, change the
password and upgrade firmware.
Installing the Web Management Utility
The following are step-by-step instructions for installing the Web
Management utility.
1. Insert the Utility CD in the CD-ROM Drive.
2. Click Install Utility icon to start
3. Follow the on-screen instructions to install the utility.

15
4. Upon completion, go to Program Files -> Web Management
Utility and open the Web Management utility. (Figure 7.)
Figure 7. Web Management Utility
The Web Management Utility is divided into four sections, Discovery
List, Monitor List, Device Setting and Toolbar function, for details
instruction, follow the below section.
Discovery List
This list shows all the Web management devices in the network.
Click “Discovery” button to list all the Web Management devices in
the discovery list.
Double click or press “Add to monitor list” to select add a device to
the Monitor List.
16
System word definitions in the Discovery List:
zMAC Address: Shows the MAC Address of the Switch.
zIP Address: Shows the current IP address of the Switch.
zProtocol version: Shows the version of the Utility protocol.
zProduct Name: Shows the product name of the Switch.
zSystem Name: Shows the system name of the Switch.
zLocation: Shows the location of the Switch.
zTrap IP: Shows the IP where the Trap is to be sent.
zSubnet Mask: Shows the Subnet Mask.
zGateway: Shows the Gateway.
Monitor List
All the switches in the Monitor List can be monitored; you can also
monitor traps and show the status of the device.
System word definitions in the Monitor List:
zS: Shows the system symbol of the Switch. means the Switch
is not connected.
zIP Address: Shows the current IP address of the device.
zMAC Address: Shows the MAC Address of the Switch.
zProtocol version: Shows the version of the Utility protocol.
zProduct Name: Shows the product name of the Switch.
zSystem Name: Shows the system name of the Switch.
zDHCP: Shows the DHCP status of the device
zLocation: Shows where the device is located.

17
zTrap IP: Shows the IP where the Trap is to be sent.
zSubnet Mask: Shows the Subnet Mask.
zGateway: Shows the Gateway.
View Trap: The Trap function allows you to monitor events that
occur with the Switches in the Monitor List.
There is an LED indicator next to the “View Trap” button. When the
LED is green, it means that there is no trap transmitted. When the
LED is red, it means a new trap has been transmitted. (Figure 8)
Figure 8.
When “View Trap” is clicked, a Trap Information window will appear.
This window will show the trap information including the Symbol,
Time, Device IP and the Event. (Figure 9)
The symbol “ ” indicates a new Event has occurred. This symbol
will disappear after you review and click on the event record.
Figure 9.
Note: In order to receive Trap information, the Switch has to be configured
with Trap IP and Trap Events in the Web browser. See Page 31 for more
details.
18
Add Item: To add a device to the Monitor List manually, enter the IP
Address of the device that you want to monitor.
Delete Item: To delete the device in the Monitor List.
Device Setting
Configuration Setting: In this Configuration Setting, you can set the
IP Address, Subnet Mask, Gateway, Set Trap to (Trap IP Address),
System name and Location.
Select the device in the Discovery list or Monitor List and click
configuration setting. The Configuration Setting window will pop out
appear (Figure 10). After making the desired changes, enter the
password and click “Set”. The default password is “admin”.
Figure 10. Configuration Setting
Password Change: This option allows you to change the password.
Enter the original password, the new password, confirm the password
and then press “Set”.
Figure 11. Password Change

19
Firmware Upgrade: Use this option to upgrade the firmware on the
Switch.
Figure 12.
Web Access: Double click the device in the Monitor List or select a
device in the Monitor List and click “Web Access” button to access
the Switch’s Web browser configuration.
Toolbar
The toolbar in the Web Management Utility has four options; File,
View, Options and Help.
Under “File”, there are four options; Monitor Save, Monitor Save As,
Monitor Load and Exit.
zMonitor Save: To record the settings of the Monitor List to the
default. The next time you open the Web Management Utility,
it will load the default recorded setting.
zMonitor Save As: To record the setting of the Monitor List
with a specific filename and file path.
zMonitor Load: To manually load the setting file of the Monitor
List.
zExit: To exit the Web Management Utility.
20
In the “View TAB”, there are view log and clear log function, this
function will help you to show trap setting.
zView Log: To show the event of the Web Management Utility
and the device.
zClear Log: to clear the log.
In the “Option TAB”, there are Refresh Time function, this function
helps you to refresh the time of monitoring the device. Choose 15 secs,
30 secs, 1 min, 2 min and 5 min to select the time of monitoring.
In the “Help TAB”, there is About function, it will show out the
version of the Web Management Utility.
Configuring the Switch
The 48-Port 10/100/1000Mbps Gigabit Ethernet Web Smart Switch
has a Web GUI interface for smart switch configuration. The Switch
can be configured through the Web Browser. A network administrator
can manage, control and monitor the switch from the local LAN. This
section indicates how to configure the Switch to enable its smart
functions
Login
Before you configure this device, make sure the PC is configured to
be in the same the subnet as the switch. For example, since the default
the default IP address of the Web Smart Switch is 192.168.0.1, then
the PC should be set to 192.168.0.x (where x is a number between 2
and 254), with a default subnet mask of 255.255.255.0.
Open Internet Explorer 5.0 or above.

21
Enter IP address http://192.168.0.1 (the factory-default IP address
setting) into the address bar.
Figure 13.
You can also access the browser configuration through the Web
Management Utility. Select the desired Switch in the Monitor and
click “Access Web”.
When the following dialog page appears, enter the default password
"admin" and click Login.
Figure 14.
After entering the password, the system information screen will
appear.
22
Figure 15. System Information
Configuration Menu
When the main page appears, find the Configuration menu in the left
side of the screen. Click on the setup item that you want to configure.
There are sixteen options: Port Setting, IEEE 802.1Q VLAN Settings,
Trunk Setting, Mirror Setting, IEEE 802.1p Default Priority,
Broadcast Strom Control Setting, Jumbo Frame Setting, IGMP Global
Setting, IGMP VLAN Setting, System Information, System Setting,
Trap Setting, Password Setting, Statistics, Factory Reset, Backup
Setting, Firmware Upload and System Reboot as shown in the
Configuration Menu screen.

23
Configuration menu
Configuring Setup Settings
There are seven options; Port Settings, IEEE 802.1Q VLAN Setting,
Trunk Setting, Mirror Setting, IEEE 802.1p Default Priority,
Broadcast Storm Control Setting and Jumbo Frame Setting
Port Settings
In Port Settings menu (Figure 16), this screen shows each port’s status.
You can change the speed and flow control parameters by clicking on
the dropdown menu. If you want to update the link status, press the
“Refresh” button.
24
The Link Status in the screen will show the connection speed and
duplex mode. If there is no connection to the port, down will be
displayed.
Figure 16. Port Setting
Note 1: Be sure to click refresh after switching between media type (Fiber to Copper
or Copper to Fiber).
Note 2: The priority of Gigabit Fiber port is higher than Copper.
Speed:
The 1000Base-T connection can operate in Forced Mode settings
(1000M Full, 100M Full, 100M Half, 10M Full, 10M Half), Auto, or
Disable. The default setting for all ports are set to Auto. The mini-
GBIC (Gigabit Fiber) connections can operate in Forced Mode
settings (1000M Full), Auto, or Disable.

25
Flow Control:
This setting determines whether or not the Switch will be handling
flow control. Set Flow Control to Enable to avoid data transfer
overflow. Set Flow Control to Disable if flow control is not needed.
When the port is set to forced mode, then the flow control will
automatically be set to Disable.
QoS:
Displays each port’s 802.1p QoS priority level for received data
packet handling. Default setting for all ports is Middle. You can
change the priority settings in 802.1p Default Priority.
26
VLAN Settings (IEEE 802.1Q VLAN)
A VLAN is a group of ports that can be anywhere in the network, but
communicate as though they were in the same area.
VLANs can be easily organized to reflect department groups (such as
R&D, Marketing), usage groups (such as e-mail), or multicast groups
(multimedia applications such as video conferencing), and therefore
help to simplify network management by allowing users to move
devices to a new VLAN without having to change any physical
connections.
IEEE802.1Q VLAN function base on VID and PVID to distributes
different VLAN groups. But IEEE802.1Q VLAN doesn't support
multi-need server application via Untag port (Untag Port cannot
overlap in different VLAN groups). For multi-need server application
via Untag Port that the device support IEEE802.1Q Asymmetric
VLAN function can be covered it.
Asymmetric VLAN
IEEE 802.1Q Asymmetric VLAN default setting is “Disabled”, you
can press “Enabled” ratio button and Apply it to submit the
Asymmetric VLAN function.
Note: The settings of VLAN, IGMP Snooping and Forwarding table will be reset to
default.

27
Untag Asymmetric VLAN Setting:
The IEEE 802.1Q VLAN Configuration page provides powerful VID
management functions. The original default VLAN setting has the
VID as 01, named “default”, and contains all ports as “Untagged”.
802.1Q VLAN Setting
Add VID: Click to create a new VID group, assigning ports from 01 to
48 as Untag, Tag, or Not Member. A port can be “Untagged” in only
one VID. To save the VID group, press Apply.
28
VLAN Settings
VID: A unique VLAN ID.
VLAN Name: A VLAN name can be setting as user wish.
Port: The switch port number.
Untag: Outgoing frames without VLAN tag.
Tag: Outgoing frames with VLAN tag.
Not Member: The port number which not to be grouped.
Select All: Select all ports to be VLAN members or not VLAN
members.
Cancel: To call the modifications off.
Apply: To activate and save the modifications.
Delete: Click to delete selected VID
Delete VID

29
To change exist VLAN setting, press the VID to modify it.
Modify VID
30
PVID settings:
While receiving an untagged frame from the port, the switch will
assign a tag to the frame, using the PVID of the port as its VID.
PVID settings
Example 1:
Here is an example of two VLAN groups with several ports in each
group and VLAN 1 (VID 01) does not have communication with
VLAN 2 (VID 02).
Untag VLAN setting example

31
Step1: Set VID 01 port 1~24 to “Untag” ports and 25~48 to “Not Member” ports then
apply settings.
Step 2: Create VID 02 and set port 1~24 to “Not Member” ports and 25~48 to “Untag”
ports member then apply settings
32
Example 2:
802.1Q Asymmetric VLAN example:
Port 1~48 in VLAN1, port1~5 in VLAN2, port1,6~9 in VLAN3. All
VLAN1~3 have access to Internet via port 1.
Note: The multi-need server must be support IEEE 802.1Q VLAN
Asymmetric VLAN setting example
Step 1: Enable Asymmetric VLAN function
Step 2: Set VLAN1 1~48 port to “Untag” ports then apply settings.