TRENDnet TEG-082WS User manual

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 1
Contents
PRODUCT OVERVIEW .......................................................................................................2
FEATURES............................................................................................................................................2
FRONT VIEW.......................................................................................................................................3
LED INDICATORS...............................................................................................................................3
REAR VIEW .........................................................................................................................................5
PACKAGE CONTENTS .........................................................................................................................5
SWITCH INSTALLATION...................................................................................................5
DESKTOP HARDWARE INSTALLATION............................................................................................5
RACK MOUNT HARDWARE INSTALLATION....................................................................................6
BASIC INSTALLATION ........................................................................................................................6
CONNECT ADDITIONAL DEVICES TO YOUR SWITCH.......................................................................8
CONFIGURE YOUR SWITCH.............................................................................................9
ACCESS YOUR SWITCH MANAGEMENT PAGE ..................................................................................9
SWITCH INFO ......................................................................................................................................9
SYSTEM............................................................................................................................................. 11
PHYSICAL INTERFACE..................................................................................................................... 22
BRIDGE.............................................................................................................................................. 26
SNMP............................................................................................................................................... 56
ACCESS CONTROL CONFIG............................................................................................................. 63
RMON.............................................................................................................................................. 69
VOICE VLAN ................................................................................................................................... 75
SECURITY.......................................................................................................................................... 79
DESTINATION MAC FILTER.......................................................................................................... 84
DHCP SNOOPING............................................................................................................................ 86
LLDP (LINK-LAYER DISCOVERY PROTOCOL)........................................................................... 90
STATISTIC......................................................................................................................................... 93
SWITCH MAINTENANCE................................................................................................................. 94
SAVE SETTINGS TO FLASH.......................................................................................................... 101
WEB SMART SWITCH MANAGEMENT UTILITY.................................................. 102
SYSTEM REQUIREMENTS ............................................................................................................ 102
INSTALLATION...............................................................................................................................102
USING THE UTILITY......................................................................................................................103
DISCOVERY LIST............................................................................................................................104
DEVICE SETTING...........................................................................................................................105
MAIN MENU OPTIONS .................................................................................................................106
TECHNICAL SPECIFICATIONS ................................................................................... 108
TROUBLESHOOTING.................................................................................................... 110
APPENDIX........................................................................................................................ 111
HOW TO FIND YOUR IP ADDRESS? .............................................................................................111
HOW TO FIND YOUR MAC ADDRESS?........................................................................................118
REGULATIONS................................................................................................................ 119
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT..................................119
ROHS..............................................................................................................................................119
EUROPE –EU DECLARATION OF CONFORMITY.......................................................................120
LIMITED WARRANTY .................................................................................................. 121

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 2
Product Overview
TEG-082WS
Features
TRENDnet’s fanless 8-Port Gigabit Web Smart Switch, model TEG-082WS,
offers 8 x Gigabit ports, 2 x shared SFP slots, a built-in power supply, and a 16
Gbps switching capacity. This IPv6 ready switch offers advanced traffic
management, troubleshooting, access control, energy saving GREENnet, and
monitoring features at a reduced cost.
Hardware Design
Provides 8 x Gigabit ports, 2 x shared SFP slots, a 16 Gbps switching capacity,
a built-in power supply, and rackmount brackets
Fanless
Fanless design reduces energy consumption and operating noise
IPv6 Ready
This switch supports IPv6 configuration and IPv6 neighbor discovery
Traffic Management
A broad range of network configurations are supported by: 802.3ad link
aggregation, Asymmetric VLAN, 802.1Q VLAN, Voice VLAN, Private VLAN,
Bandwidth Controls, GVRP, IGMP v1-v3, 802.1p Class of Service (CoS),
Spanning Tree (STP, RSTP, and MSTP), and QoS queue scheduling
Troubleshooting
Real time traffic comparison charts, error group charts, and a convenient
cable diagnostic test aid in rapid troubleshooting
Access Controls
Features such as ACL, SSL, MAC/port filtering, Denial of Service controls,
802.1X, TACACS+, and RADIUS are compatible with layered network access
controls
Monitoring
RMON, SNMP, SNMP Trap, and Port Mirroring support administrator
monitoring solutions

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 3
Front View
Interfaces
Reset Button
Press and hold this button for 10 seconds and
release to reset the switch to factory defaults.
Gigabit Ethernet
Ports (1-8)
Connect network devices and can be used for uplink
or downlink connections. Ports 7 and 8 are shared
with SFP slots 7F and 8F and will be disabled when
SFP slots (7F, 8F) are in use.
SFP slots (7F, 8F)
Supports optional 100 or 1000BASE-SX/LX mini-GBIC
modules.
LED Indicators
Power (PWR) LED
On
The TEG-082WS is powered on.
Off
The TEG-082WS is not powered.
Link/ACT LED (per port)
On
The respective port is successfully connected to an Ethernet
network.
Blinking
The port is transmitting or receiving data on the Ethernet
network.
Off
No link.
Reset Button
LED Indicators
SFP Share Port
GbE Network Ports

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 4
Speed LED (per port)
Green
When respective LED shows in solid green LED, the port is
connected to a 1000Mbps Gigabit Ethernet network.
Amber
When respective LED shows in solid amber, the port is
connected to a 100Mbps Ethernet network.
Off
When the LINK LED is on and Speed LED is off, the respective
port is connected to a 10Mbps Ethernet network.
Duplex (per port)
On
Full duplex Ethernet
Off
Half duplex Ethernet
Shared SFP Slots (7F, 8F)
Solid
Green
The port is inserted mini-GBIC Gigabit module and gigabit link
is established.
Blink in
Green
Traffic is passing through this SPF port with gigabit link.
Solid
Amber
The port is inserted mini-GBIC 100Mbps module and 100M
link is established.
Blink in
Amber
Traffic is passing through this SPF port with 100Mbps link.
Off
No link

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 5
Rear View
AC Power Connector –Connect the AC power cord to the connector and the
other side into a power outlet. (Input: 100~240VAC, 50/60Hz)
Package Contents
TEG-082WS package includes:
•TEG-082WS
•Multi-Language Quick Installation Guide
•CD-ROM (Utility and User’s Guide)
•Power cord (1.8 m / 6 ft.)
•Rack mount hardware
If any package content is missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Switch Installation
Desktop Hardware Installation
The site where you install the switch stack may greatly affect its performance.
When installing, consider the following pointers:
Note: The model showing in illustrations may be different to the one you have.
Install the Switch in a fairly cool and dry place.
Install the Switch in a site free from strong electromagnetic field
generators (such as motors), vibration, dust, and direct exposure to
sunlight.
Leave at least 10cm of space at the front and rear of the hub for
ventilation.
Install the Switch on a sturdy, level surface that can support its weight,
or in an EIA standard-size equipment rack. For information on rack
installation, see the next section, Rack Mounting.
When installing the Switch on a level surface, attach the rubber feet
to the bottom of each device. The rubber feet cushion the hub and
protect the hub case from scratching.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 6
Rack Mount Hardware Installation
The switch can be mounted in an EIA standard-size, 19-inch rack, which can
be placed in a wiring closet with other equipment. Attach the mounting
brackets at the switch’s front panel (one on each side), and secure them with
the provided screws.
Note: The switch model may be different than the one shown in the example
illustrations.
Then, use screws provided with the equipment rack to mount each switch in
the rack.
Basic Installation
1. Power on your TEG-082WS and connect your computer to the switch.
2. Assign a static IP address to your computer’s network adapter in the
subnet of 192.168.10.x (e.g. 192.168.10.25) and a subnet mask of
255.255.255.0.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 7
3. Open your web browser, and enter the IP address of the switch, and then
press Enter. The default IP address is 192.168.10.200.
4. Enter the User Name and Password, and then click Login. The default
username is admin and the password is admin as well. The username and
password are case sensitive, please enter them in all lower cases.
5. Click System and then click IPv4 Setup.
6. Configure the switch IP address settings to be within your network subnet,
then click Apply.
Note: You may need to modify the static IP address settings of your computer’s
network adapter to IP address settings within your subnet in order to regain
access to the switch.
To store the change to flash memory so you can access the same switch
management IP address, please follow the instruction below.
7. Click Save Settings to Flash on the bottom of the menu.
8. Click button, then click OK.
Note: Once the settings are saved, you can connect the switch to your network.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 8
Connect additional devices to your switch
You can connect additional computers or other network devices to your switch using Ethernet cables to connect them to one of the available Gigabit Ethernet
Ports (1-8). Check the status of the LED indicators on the front panel of your switch to ensure the physical cable connection from your computer or device.
Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings. Please ensure that your
computer or device network settings (also called TCP/IP settings) are configured properly within the network subnet your switch is connected.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 9
Configure your switch
Access your switch management page
Note: Your switch default management IP address http://192.168.10.200.
You can manage the TEG-082WS websmart switch using Internet web
browser on your choice. (e.g. Internet Explorer®, Firefox®, Chrome™, Safari®,
or Opera™).
1. Open your web browser and enter the IP address of the switch, such as
http://192.168.10.200. Your switch will prompt you for a user name and
password.
9. Enter the User Name and Password, and then click Login. The default
username is admin and the password is admin as well. The username and
password are case sensitive, please enter them in all lower cases.
Switch Info
You’ll landing on Switch Info page when login to the web management GUI.
You can view your switch status information here.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 10
Switch Information
System Up For:
The duration your switch has been running
continuously without a restart/power cycle (hard or
soft reboot) or reset.
Runtime Image:
The current software or firmware version your
switch is running.
Boot Loader:
The current boot loader version your switch is
running.
Hardware Information
DRAM Size:
Displays your switch RAM memory size.
Flash Size:
Displays your switch Flash memory size.
Administration Information
System Name:
Displays the identifying system name of your switch.
This information can be modified under the System
section.
System Location:
Displays the identifying system location of your
switch. This information can be modified under the
System section.
System Contact:
Displays the identifying system contact or system
administrator of your switch. This information can
be modified under the System section.
System MAC Address, IPv4 Information
MAC Address:
Displays the switch system MAC address.
IP Address:
Displays the current IPv4 address assigned to your
switch.
Subnet Mask:
Displays the current IPv4 subnet mask assigned to
your switch.
Default Gateway:
Displays the current gateway address assigned to
your switch.
IPv6 Information
IPv6 Unicast Address
/ Prefix Length:
Displays the current IPv6 address and prefix
assigned to your switch.
IPv6 Default
Gateway:
Displays the current IPv6 default gateway address
assigned to your switch.
Link Local Address /
Prefix Length:
Displays the current Link Local address and prefix
length assigned to your switch.
Automatic Network Features
IPv4 DHCP Client
Mode:
Displays if your switch IPv4 address setting is set to
DHCP client.
IPv6 DHCP Client
Mode:
Displays if your switch IPv6 address setting is set to
DHCP client.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 11
System
System Management
System > System Management
This section explains how to assign a name, location, and contact information
for the switch. This information helps in identifying each specific switch
among other switches in the same local area network. Entering this
information is optional.
Management
System
Description:
Specifies the Switch model. You cannot change this
parameter.
System Object
ID:
Indicates the unique SNMP MIB object identifier that
identifies the switch model. You cannot change this
parameter.
System Name:
Specifies a name for the switch, the name is optional
and may contain up to 15 characters.
System
Location:
Specifies the location of the switch. The location is
optional and may contain up to 30 characters.
System Contact:
Specifies the name of the network administrator
responsible for managing the switch. This contact
name is optional and may contain up to 30 characters.
Click Apply to apply the change to the switch
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 12
Set your IPv4 settings
System > IPv4 Setup
This section allows you to change your switch IPv4 address settings. Typically,
the IP address settings should be changed to match your existing network
subnet in order to access the switch management page on your network.
IPv4 Setup
System MAC
Address:
Displays the switch MAC address information.
System IP
Address:
Enter the new switch IP address. (Default:
192.168.10.200)
System Subnet
Mask:
Enter the new switch subnet mask. (e.g.
255.255.255.0)
System Default
Gateway:
Enter the default gateway IP address. (e.g.
192.168.10.1 or typically your router/gateway to the
Internet).
System IP Mode:
Click the drop-down list and select Static to
manually specify your IP address settings or DHCP to
allow your switch to obtain IP address settings
automatically from a DHCP server on your network.
Click Apply to apply the change to the switch
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 13
Set your IPv6 settings
System > IPv6 System Settings
Use the IPv6 System Settings page to configure the IPv6 network interface,
which is the logical interface used for in-band connectivity with the switch via
all of the switch's front-panel ports. The configuration parameters associated
with the switch's network interface do not affect the configuration of the
front-panel ports through which traffic is switched or routed.
IPv6 System Settings
IPv6 State:
The IPv6 address for the IPv6 network interface is
set in auto configuration mode if this option is
enabled. The default value is. Auto configuration can
be enabled only when DHCPv6 is not enabled on any
of the management interfaces.
DHCPv6 Client:
This option only displays when DHCPv6 is enabled.
IPv6 Unicast
Address / Prefix
Length:
The IPv6 Unicast Address is an identifier for a single
interface, on a single node. A packet that is sent to a
unicast address is delivered to the interface
identified by that address. Add the IPv6 prefix and
prefix length to the IPv6 System Settings interface.
IPv6 Static
Gateway:
Specifies the corresponding Gateway of the IP
address entered into the field.
IPv6 Dynamic
Gateway:
To configure the switch to automatically obtain its IP
configuration from a DHCP server on your network.
NS Retransmit Time Settings
NS Retransmit
Time:
A constant that defines a nonzero number of
seconds between periodic re-authentication of the
client. The field is 1~3600 seconds. The default
setting is 1 second.
Link Local Address Settings
Automatic Link
Local Address:
A link local address has a prefix of FE80, is not
routable, and can be used for communication only
on the local network. Only one link local address is
supported. If a link local address exists on the
interface, this entry replaces the address in the
configuration.
Link Local
Address/Prefix
length:
Enter the Link Local Address/Prefix Length.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 14
A link-local address is an IPv6 unicast address that can be automatically
configured on any interface using the link-local prefix FE80/10 and the
interface identifier in the modified EUI-64 format. Link-local addresses are
used in the neighbor discovery protocol and the stateless auto configuration
process. Nodes on a local link can use link-local addresses to communicate;
the nodes do not need globally unique addresses to communicate. IPv6
devices must not forward packets that have link-local source or destination
addresses to other links.
Click Apply to apply the change to the switch.
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.
DNS Settings
System > DNS Settings
Some of the smart switch services requires name resolution services to finish
its job, such as SNTP service. Setup the DNS server settings here for name
resolution.
DNS Server Settings
DNS IPv4 Server:
Specifies the IPv4 DNS server address.
DNS IPv6 Server:
Specifies the IPv6 DNS server address.
Click Add to save the entry to the list.
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 15
Add IPv6 neighbors
System > IPv6 Neighbor Settings
These settings allows you to manually define IPv6 supported neighboring
devices on your network.
IPv6 Neighbor Settings
Neighbor IPv6
Address:
Specifies the neighbor IPv6 address.
Link Layer MAC
Address:
Specifies the link layer MAC address.
Click Add to save the entry to the list.
You can type in the specific address and click Find to find the entry to modify
or click Delete to delete the address. If the entries span multiple pages, you
can navigate page number in the Page field and click Go or you can click First,
Previous, Next, and Last Page to navigate the pages.
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.
Restrict access to switch management page
System > IP Access List
This section allows you to define or restrict access to the switch management
page to a list of specific IP addresses.
IP Access List
IP Restriction
Status:
Enable or disable Access Control List. Default:
Disabled
IP Address Settings
IP Address:
Enter the IPv4 or IPv6 address and then click Add to
create an access list entry.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 16
IP Access List Table
For each entry, the access list will populate. You can click Delete next to the
entry to delete the entry or Delete All to delete all entries in the table.
When you have completed entering the IPv4 and IPv6 address entries, click
the IP Restriction Status drop-down list at the top and select Enabled, then
click Apply.
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.
Change administrator password and add accounts
System > Administration
This section explains how to change the administrator password create
additional administrative user accounts for access to the switch management
page.
To create additional administrative user accounts
Administration Settings
User Name:
Enter the user name of the new account.
Password:
Enter the password for the new account
Confirm Password:
Enter the password again for verification.
Note: The password consists of up to 12 alphanumeric characters.
Click Add to add the new administrator.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 17
Changing the administrator password
In the Password field, enter the new password and enter the new password
again the Confirm Password field to verify. Then, click Apply.
Note: The password consists of up to 12 alphanumeric characters. The
index 1 admin user on the administration table is the default
administrator. You can modify the password, but you cannot remove it.
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.
Enable or disable SNMP and modify idle timeout settings
System > User Interface
This section explains how to enable SNMP on the switch and modify the
switch management page idle timeout settings.
Note: If you disable the SNMP on the switch, the switch will not be manageable via
SNMP using MIBs.
Status Settings
SNMP Agent:
Click the drop-down list to one of the following
options.
Enabled: The SNMP agent is active. You can
manage the switch with SNMP network
management software and the switch’s private
MIB.
Disabled: The SNMP agent is inactive.
Web Server Status:
Displays the current SNMP status.

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 18
Timeout Settings
Web Idle Timeout:
Enter the idle period in minutes, when the switch
will automatically log out an idled user from the
switch management page. Default: 10 min.
Group Interval:
The IGMP group timeout interval. Default: 120 sec.
Click Apply to apply the change to the switch
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.
Set the switch date and time
System > System Time

TRENDnet User’s Guide TEG-082WS
© Copyright 2014 TRENDnet. All Rights Reserved. 19
Current Time Settings
Clock Mode:
Displays if system time and date is set manually Local
Time or obtained automatically from a network time
server SNTP.
Current Time:
Displays the current system time and date.
Time Zone:
Displays the current system time zone.
Date/Time Settings
Clock Mode:
Select Local Time to manually configure your date and
time settings or select SNTP to configure your switch
to automatically obtain settings from a network time
server.
Local Time Settings
Date Settings:
Enter your date settings (YYYY/MM/DD).
Time Settings:
Enter your time settings (HH:MM:SS)
When select the clock mode to Local Time, enter the date and time manually
here.
Simple Network Time Protocol (SNTP) Settings
SNTP Primary
Server:
Select the format of the URL you want to enter for
SNTP server address. Enter the primary network time
server IPv4, IPv6 address or domain name.
SNTP Secondary
Server:
Select the format of the URL you want to enter for
SNTP server address. Enter the secondary network
time server IPv4, IPv6 address or domain name.
SNTP Poll
Interval:
Enter the interval time when your switch will update
the time and date settings with the time server.
Default: 1 min.
Time Zone
Click the drop-down list to select your time zone.
When select the clock mode to SNTP, enter the SNTP server information here.
Click Apply to apply the change to the switch
Go Save Settings to Flash section to save the change on the flash to make
sure the change is permanent.