TRENDnet TEG-40080ES User manual

© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
Cover Page
1

© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEG-40080ES
i
Contents
Product Overview ............................................................................ 1
Package Contents........................................................................................................1
Features......................................................................................................................1
Product Hardware Features ........................................................................................2
Switch Installation ........................................................................... 4
Desktop Hardware Installation....................................................................................4
Rack Mount Hardware Installation..............................................................................4
Basic Installation .........................................................................................................5
Connect additional devices to your switch ..................................................................6
Configure your switch...................................................................... 7
Access your switch management page........................................................................7
System Info .................................................................................................................7
View your switch status information .................................................................7
System ........................................................................................................................8
Set your system information .............................................................................8
Set your IPv4 settings ........................................................................................9
Set your IPv6 settings ......................................................................................10
Restrict access to switch management page....................................................11
Change administrator password and add accounts..........................................11
Physical Interface......................................................................................................12
Configure Physical Interfaces...........................................................................12
Bridge .......................................................................................................................13
Configure Trunking ..........................................................................................13
Configure port mirror settings .........................................................................14
Enable loopback detection ..............................................................................15
Configure IGMP Snooping Settings ..................................................................15
Configure Storm Control..................................................................................16
Set Ingress / Egress Rate Limiting ....................................................................16
Configure VLAN Port Settings ..........................................................................18
Configure the VLAN forwarding Table..............................................................18
QoS (Quality of Service) ............................................................................................ 19
Set IEEE 802.1P settings .................................................................................. 19
Set Port-Based QoS ......................................................................................... 20
Statistics ................................................................................................................... 21
View Traffic Information Statistics................................................................... 21
Switch Maintenance ......................................................................21
Upgrade your switch firmware.................................................................................. 21
Firmware Upgrade via HTTP Settings............................................................... 22
Backup and restore your switch configuration settings ............................................. 22
Backup/Restore via HTTP Settings................................................................... 22
Cable Diagnostics Test .............................................................................................. 23
Enable IEEE 802.3az Power Saving Mode .................................................................. 23
Reboot/Reset to factory defaults.............................................................................. 24
Switch Management Page Structure ..............................................25
Technical Specifications .................................................................25
Troubleshooting.............................................................................27
Appendix .......................................................................................28

© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEG-40080ES
1
Product Overview
TEG-40080ES
Package Contents
In addition to your switch, the package includes:
Quick Installation Guide
CD-ROM (User’s Guide)
Power adapter (12V DC, 3.5A)
RJ-45 to RS-232 console cable (1 m / 3.28 ft.)
Rack mount kit
If any package contents are missing or damaged, please contact the retail store, online
retailer, or reseller/distributor from which the product was purchased.
Features
TRENDnet’s 8-Port 10G Easy Smart Switch with 8 x 10GBASE-T ports, model TEG-
40080ES, is a cost-effective switch solution for high-speed 10 Gigabit network server
connections. This easy smart switch features the most commonly used managed switch
features, reducing unnecessary switch complexity. The web-based management
interface offers features for traffic control, troubleshooting, access controls, and
monitoring. TRENDnet’s TEG-40080ES allows for simple network integration into your
SMB network
High-Speed 10GBASE-T
Offers eight 10GBASE-T Ethernet ports for high-speed network uplink or downlink NAS /
access server connections providing a cost-effective solution in adding 10G link
capability to an SMB network.
Easy Smart Management
Provides an easy to use web-based GUI management for reduced switch configuration
complexity and offers a combination of more commonly used SMB management
features for easy deployment.
Integration Flexibility
Managed features include access control lists, VLAN, IGMP Snooping, and QoS for
flexible network integration
Hardware
Provides 8 x 10GBASE-T ports for high-speed network uplink or downlink server
connections, and 1U rack mountable.
Smart Fan
Smart fan saves energy by auto-adjusting the fan speed and use based on cooling needs.

© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEG-40080ES
2
Network Management
A broad range of network configurations are supported by: 802.3ad link aggregation,
802.1Q VLAN, bandwidth controls, IGMP, loopback detection, port mirroring and 802.1p
(QoS).
Troubleshooting
Traffic statistics and a convenient cable diagnostic test aid in network troubleshooting.
Product Hardware Features
LED on/off –Press and hold to turn LED lights on or off
LED Indicators –Indicator for device Power and System status.
10GBASE-T Ethernet Ports (1-8) –Connect network devices or servers
Console Port ––Use the included RJ-45 to RS-232 serial console cable to
access the out-of-band command line interface management.
Reset Button- Press and hold this button for 8 seconds and release to
reset the switch to factory defaults. The ports LEDs will turn off to
indicate that the reset was initiated.
Power Port –Power the device through an external AC power adapter
(supports AC 100 –240V, 50-60Hz)

© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEG-40080ES
3
LED Indicators
POWER LED
On
:
When the POWER LED light is on, the device is receiving
power.
Off
:
When the Power turns off, the power adapter is not
connected or the device is not receiving power.
SYSTEM LED
On (Amber)
:
When the amber SYSTEM LED light is on, the device is
booting up
On (Green)
:
When the green SYSTEM LED light is on, the device has
finished booting and is ready for operation.
LED ON/OFF Button
Click Once
:
When the LED ON/OFF button is clicked, the device will
disable all LED lights aside from the POWER LED.
Hold 3
Seconds
:
When the LED ON/OFF button is held for 3 seconds, the
device will automatically begin running cable diagnostics.
10GBASE-T Ethernet Port LEDs
Link/Activity (Left hand LED - per port)
On (Amber)
:
When the Link/Act LED is on, the link established is
operating at 100/1000Mbps speeds.
On (Green)
:
When the Link/Act LED is on, the link established is
operating at 10Gbps speeds.
Off
When the Link/Act LED light is off, there is no
established connection.
10GBASE-T Ethernet Port LEDs
Cable Diagnostic (Right hand LED - per port)
Blinking
(Green)
:
When the CABLE DIAGNOSTIC LED is blinking, the port
is executing cable diagnostics.
On (Green)
When the CABLE DIAGNOSTIC LED is on, the diagnostic
has determined a healthy connection.
On (Amber)
:
When the CABLE DIAGNOSTIC LED is on, the diagnostic
has determined an unhealthy connection.

© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEG-40080ES
4
Switch Installation
Desktop Hardware Installation
The site where you install the switch may greatly affect its performance. When
installing, consider the following pointers:
Note: The switch model may be different than the one shown in the example
illustrations.
Install the Switch in a fairly cool and dry place.
Install the Switch in a site free from strong electromagnetic field generators (such
as motors), vibration, dust, and direct exposure to sunlight.
Leave at least 10cm of space at the front and rear of the hub for ventilation.
Install the Switch on a sturdy, level surface that can support its weight, or in an
EIA standard-size equipment rack. For information on rack installation, see the
next section, Rack Mounting.
When installing the Switch on a level surface, attach the rubber feet to the
bottom of each device. The rubber feet cushion the hub and protect the hub
case from scratching.
Rack Mount Hardware Installation
The switch can be mounted in an EIA standard-size, 19-inch rack, which can be placed in
a wiring closet with other equipment. Attach the mounting brackets at the switch’s
front panel (one on each side), and secure them with the provided screws.
Note: The switch model may be different than the one shown in the example
illustrations.
Then, use screws provided with the equipment rack to mount each switch in the rack.

© Copyright 2017 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TEG-40080ES
5
Basic Installation
3. Assign a static IP address to your computer’s network adapter in the subnet of
192.168.10.x (e.g. 192.168.10.25) and a subnet mask of 255.255.255.0.
4. Open your web browser, and type the IP address of the switch in the address bar, and
then press Enter. The default IP address is 192.168.10.200.
5. Enter the User Name and Password, and then click Login. By default:
User Name: admin
Password: admin
Note: User name and password are case sensitive.
6. Click System and then click IPv4 Setup.
7. Configure the switch IP address settings to be within your network subnet, then click
Apply to save changes.
Note: You may need to modify the static IP address settings of your computer’s network
adapter to IP address settings within your subnet in order to regain access to the switch.
5. The browser will automatically use the new IP address to reconnect to the device and
bring you back to the login page. Re-login using the default User Name and Password.

© Copyright 2017 TRENDnet. All Rights Reserved.
6
TRENDnet User’s Guide
TEG-40080ES
Connect additional devices to your switch
You can connect computers/servers or other network devices to your switch using Ethernet cables to connect them to one of the available 10GBASE-T Ethernet Ports. Check the status of
the LED indicators on the front panel of your switch to ensure the physical cable connection from your computer or device. You can use either the 10GBASE-T Ethernet ports connections
as network uplinks.
Note: If you encounter issues connecting to your network, there may be a problem with your computer or device network settings. Please ensure that your computer or device network
settings (also called TCP/IP settings) are configured properly within the network subnet your switch is connected.
10G Capable Workstation 10G Capable Workstation Server

© Copyright 2017 TRENDnet. All Rights Reserved.
7
TRENDnet User’s Guide
TEG-40080ES
Configure your switch
Access your switch management page
Note: Your switch default management IP address http://192.168.10.200 is accessed
through the use of your Internet web browser (e.g. Internet Explorer®, Firefox®,
Chrome™, Safari®, Opera™) and will be referenced frequently in this User’s Guide.
1. Open your web browser and go to the IP address http://192.168.10.200. Your switch
will prompt you for a user name and password.
2. Enter the user name and password. By default:
User Name: admin
Password: admin
Note: User Name and Password are case sensitive.
System Info
View your switch status information
System Info
You may want to check the general system information of your switch such as firmware
version and system uptime. Other information includes administration information,
IPv4 and IPv6 information.
1. Log into your switch management page (see “Access your switch management page”
on page 7).
2. Click on System Info.
System Information
System Up For –The duration your switch has been running continuously without
a restart/power cycle (hard or soft reboot) or reset.
Runtime Image: The current software or firmware version your switch is running.
Administration Information
System Name –Displays the identifying system name of your switch. This
information can be modified under the System section.

© Copyright 2017 TRENDnet. All Rights Reserved.
8
TRENDnet User’s Guide
TEG-40080ES
System MAC Address, IPv4 Information
MAC Address: Displays the switch system MAC address.
IP Address –Displays the current IPv4 address assigned to your switch.
Subnet Mask –Displays the current IPv4 subnet mask assigned to your switch.
Default Gateway –Displays the current gateway address assigned to your switch.
IPv6 Information
IPv6 Address: Displays the current IPv6 address and prefix assigned to your
switch.
Automatic Network Features
IPv4 DHCP Client Mode: Displays if your switch IPv4 address setting is set to
DHCP client.
System
Set your system information
System > System Management
This section explains how to assign a name for the switch. This information helps in
identifying each specific switch among other switches in the same local area network.
Entering this information is optional.
1. Log into your switch management page (see “Access your switch management page”
on page 7).
2. Click on System
3. Review the System Management settings. When you have completed making
changes, click Apply to save the settings.
System Description - Specifies the switch model. You cannot change this
parameter.
System Name - Specifies a name for the switch, the name is optional and may
contain up to 15 characters.
Link Ports - Specifies the ports with an established link.
Bonjour –A discovery protocol that enables automatic discovery of services
and devices within the IP networks. Bonjour is disabled by default.
4. Click Apply to save configuration changes to the NV-RAM to ensure that if the switch
is rebooted or power cycled, the configuration changes will still be applied.