TRENDnet TEG-S081FMi User manual

TEG-S081FMi
Quick Installation Guide

Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
4
2
8
1. Before You Start
2. Hardware Installation ........................................................................
3. Configure the Switch .........................................................................
................................................................................
Table of Contents
Version 12.19.2007

System Requirements
Application
Package Contents
1. Before You Start
English
1
?
?User Guide CD-ROM
?Quick Installation Guide
?2 Mounting Brackets with Screws
?RS-232 cable
?AC Power Cord
TEG-S081FMi
?
?
?
?
?
?
Web Browser: Internet Explorer (6.0 or above)
Computer with Serial port
Computer with Fiber connection or a Media Converter (e.g. TFC-210MSC,
TFC-2000MSC, TFC-2000S20)
50/125 or 62.5/125 µm Multimode Fiber cable with SC-type connectors for
100BaseFX ports
Multimode or Single-mode Fiber cables with LC-type connectors for
Mini-GBIC modules (optional)
Mini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,
TEG-MGBS80, TEG-MGBS10D3_D5, TEG-MGBS40D3_D5) for
Mini-GBIC slots
16-Port 10/100/1000Mbps Gigabit
Web Smart Switch with Mini-GBIC Slots
(TEG-160WS)
8-Port 100base-FX SNMP Layer 2 Managed Switch
(TEG-S081FMi)
Multi-Mode Fiber
Mini-GBIC Modules
(TEG-MGBSX)
Workstations with Gigabit Adapters
(TEG-PCBUSR)
Console Connection
(RS-232)
Media Convertor
RS-232
Workstation with Gigabit Adapter
(TEG-PCBUSR)
1000MbpsFiber 10/100Mbps

2. Hardware Installation
English
2
1. Connect the Power Cord to the
rear of the TEG-S081FMi and then
to a power outlet. Then press on
the power switch to turn the switch
on.
Note: After hardware installation is complete, use the Web-based Smart Utility
to configure the TEG-S081FMi. To access the Web-based Smart Utility, open
your web browser, and enter the default IP Address http://192.168.16.1 and
default password "admin". Make sure your computer and the TEG-S081FMi
are configured to the same network segment.

English
3
2. Slide a TRENDnet mini-GBIC
module into the mini-GBIC slot
(optional).
3. Connect a Fiber cable to one of the
ports on the switch and to a fiber
connection on your network.
Note:
1. TRENDnet mini-GBIC modules
have LC-type fiber connectors.
If your fiber Gigabit connection
is SC-Type, you need a LC to
SC fiber connector.
2. TRENDnet mini-GBIC modules
are straight Gigabit. Your fiber
connection must be Gigabit
when connecting to a mini-GBIC
module.

English
4
Note: Before the Switch can be configured, a Static IP address must be
assigned on your computer's network adapter in the subnet of 192.168.16.x.
Since the Switch's default IP address is 192.168.16.1, make sure no other
network devices are assigned an IP address of 192.168.16.1. (Refer to
Troubleshooting section on how to configure TCP/IP settings on your PC.)
3. Configure the Switch
Browser Configuration
2. Enter the User name and
Password, and then click OK.
By default:
User Name: root
Password: root
1. Open your web browser, type
http://192.168.16.1 in the Address
bar, and then press Enter.
3. Click Administrator > IP
Address. Then change the IP
Address to be in the same subnet
as your Network. Enter the
Subnet Mask and Gateway to
match your network. Then click
Apply.

English
5
2. Go to Start > Programs >
Accessories > Communications >
HperTerminal
Hyper Terminal
3. Enter a name, choose an icon and
then click OK.
4. Select the correct COM port (e.g.
COM1, COM2) and then click OK.
1. Connect the RS-232 cable from a
serial port on your Windows PC to
the console port on your computer.

English
6
6. Press Enter.
5. Enter the following, click Apply
and then click OK:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
7. Type in the user name and
password and then press Enter.
By default, the user name and
password is root.
8. Press Tab to navigate to Switch
Static Configuration and then
press Enter.

English
7
9. Press Tab to navigate to
Administration Configuration
and then press Enter.
10. Use tab to navigate to Edit then
hit enter. Change the IP Address
to be in the same subnet as your
Network. Enter the Subnet Mask
and Gateway to match your
network. Press the down arrow,
press tab to navigate towards
Save and then press Enter. Then
press any key to return to the
previous screen.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet

8
Troubleshooting
Q1:
A1:
After connecting the TEG-S081FMi to a power outlet, the LEDs do not turn on.
Check the connection of the power cord to the TEG-S081FMi and the power outlet. Also
check that the power outlet is receiving power.
Q3:
A3:
I connect the switch to my network, but I am unable to make a connection
First, verify that you are using the proper fiber cable. Second, verify that the TX and RX
cables have been reverse on the opposite Fiber connection. Third, when connecting to the
mini-GBIC modules, your Fiber connection must be Gigabit. Fourth, power down the
switch. Wait 15 seconds, then plug the switch back in.
Q4:
A4:
I changed the IP address of the switch, but I forgot it. How do I reset my TEG-S081FMi?
Follow the instructions below:
1) Connect the RS-232 cable from a serial port on your Windows PC to the console
port on your computer.
2) Go to Start > Programs > Accessories > Communications > Hyperterminal
3) Enter a name, select an icon and then click OK.
4) Select the correct COM port (e.g. COM1, COM2) and then click OK.
5) Enter the following, click Apply and then click OK:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
6) Press Enter.
7) Enter the user name and password. By default, the user name and password is root.
8) Press Tab to navigate to Reboot Switch and then press Enter.
9) Press Tab to navigate to Default and then press Enter.
10)Press yto continue.
The default IP address of the switch is 192.168.16.1.
If you still encounter problems or have any questions regarding the TEG-S081FMi, please
contact TRENDnet’s Technical Support Department.
Q2: How do I configure TCP/IP settings on my computer?
1. Go into the Control Panel and double-click the Network
Connections icon, right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Use the following IP
address, and make sure you assign your network
adapter an IP address in the subnet of 192.168.16.x.