TRENDnet TPE-S80 User manual

TPE-S80
1.01
Quick Installation Guide

Table of Contents
Version 04.06.2010
English 1
1. Before You Start
2. 1
LEDs 2
3. Hardware Installation 3
echnical Specifications 7
Troubleshooting 8

1. Before You Start
Package Contents
?TPE-S80
?Multi-Language Quick Installation Guide
?Power cord
?Rackmount Kit
?Rubber Feet
System Requirements
1
?Computer with Network adapter installed
?RJ-45 Network Cable
?The surface must support at least 1.5 Kg for the Switch
?The power outlet should be within 1.82 meters (6 feet) of the Switch
?Make sure that there is proper heat dissipation from and adequate ventilation
around the Switch
?Do not place heavy objects on the Switch
?IEEE 802.3af Powered Device
?TPE-112S (Optional)
?EIAstandard 19” rack (Optional)
Note: TheTPE-S80 only supports Powered Devices that follow the
IEEE 802.3af standard

2. LEDs
2
Link/ACT
Green(Solid):Linktoanotherdevice
Green(Blinking):Activityisoccurringfromthelink
Not Illuminated: No valid network connection on
the port.
PoE
Amber:LinktoPoEdevice
NotIlluminated:NoPoEdeviceisconnected
Power
Amber:Powerison
NotIlluminated:Powerisoff

3
3. Hardware Installation
2. Move the Power switch to the on position.
1. Connect the Power Cord to the TPE-S80 and
then to a power outlet.
3. Connect a RJ-45 network cable from the
computer to an available Ethernet port on the
TPE-S80.

4
5. Verify that the following panel lights are on:
Power, PoE and Link/ACT.
4. Connect a RJ-45 cable from a PoE port (1~8)
on the TPE-S80 to the LAN port of the PoE
device (e.g. TEW-638PAP)

5
Note: Take note of the output power for your non-PoE device.The TPE-112GS only
supports non-PoE devices with an out put power of 5V, 7.5V, 9V or 12V.
Using a non-PoE device with the TPE-S80 and the TPE-112GS PoE Splitter
1. Select the proper voltage (5V, 7.5V, 9V or 12V).
2. Connect an Ethernet cable from a PoE port
on the TPE-S80 switch to the PoE IN port on
the TPE-112GS.
4. Connect the provided Jumper cable to the
non-PoE device (e.g. TEW-639GR) and to the
TPE-112GS.
3. Connect the built-in Ethernet cable (Data Out)
on the TPE-112GS to the non-PoE device's
LAN port (e.g. TEW-639GR).
5. Verify that the following panel lights are on:
Power, PoE and Link/ACT.

6
The Switch can be mounted in an EIAstandard-size, 19-inch rack, which can be placed
in a wiring closet with other equipment.
Rack Mount
1. Attach the mounting brackets to both sides of
the chassis and secure them with the provided
screws.
2. Carefully position the chassis onto the rack.
Align the bracket to the screw holes on the
rack, then use the screws provided with the
equipment rack to mount the chassis.

7
Technical Specifications
Hardware
Standard
?IEEE 802.3 10Base-T
?IEEE802.3u 100Base-TX
?IEEE 802.3af Power over Ethernet
?IEEE 802.3x Flow Control
8 x 10/100MbpsAuto-MDIX PoE ports
On/Off power switch
?Ethernet: 10/20Mbps (half/full duplex)
?Fast Ethernet: 100/200Mbps (half/full duplex)
512Kbits
1K MAC entries
1.6Gbps
100~240VAC 50/60Hz, internal universal switching power
Power, Link/Activity, PoEAct/Status
?6 Watts max. (no Power Device (PD) connected)
?132 Watts max. (8 x 15.4 watts PoE devices connected)
?Operating: 0°~ 45°C (32°~ 113°F)
?Storage: -10°~ 70°C (14°~ 158°F)
Ports
Power Switch
Data Transfer Rates
Data RAM Buffer
Address Table
Switch Fabric
Power
Diagnostic LEDs
Power Consumption
Temperature
10%- 95% (non-condensing)
266 x 160 x 44 mm (10.5 x 6.3 x 1.73 in.)
1.4 kg (3.1 lb)
CE, FCC
?Up to 15.4 watts per port; PD classification
?Polymer switch for short protection
?PoE: pin 3,6 for power (+) and pin 1,2 for power (-)
Humidity
Dimensions
Certifications
Weight
PoE
Power over Ethernet

Troubleshooting
8
1.After connecting the Switch to a power outlet, the LEDs do not turn on.
1. Check the connection of the power cord to the TPE-S80 and the power outlet.
2. Verify that the power switch is set to the On position.
3. Check that the power outlet is receiving power.
2.After I connect my PCs to the Switch, I am unable to share files.
1. Check the LEDs on the Switch. Make sure the Link/ACT LED is on.
2. Check the network cable. The minimum length of the cable is 1.5 meters and
the maximum length of the cable is 100 meters.
3. Disable any software firewall program.
4. Verify that you have file sharing enabled. Please contact your Operating
System support for more information.
3.After I connect my PCs to the Switch, I can only get onto the Internet from one
computer.
The Switch was not designed to share Internet between multiple computers. You
need to get an Internet router such as the TW100-S4W1CA.
4. My 802.3af Powered Device does not power on when I plug the device into the
Switch. What should I do?
1. Verify that the PoE device supports IEEE 802.3af protocol.
2. Verify that the power switch is set to the on position.
3. Power cycle the PoE switch. Unplug power to the Switch, wait 15 seconds,
then plug the power back in.
4. Plug the device into a different port on the PoE switch.
5. Try using another RJ-45 network cable.
5. Where is the uplink port located on the Switch?
Since all the ports on the Switch areAuto-MDIX, any of the ports can be used as
an uplink port.
If you still encounter problems or have any questions regarding the TPE-S80 please
contact Trendnet's Technical Support Department.