TRENDnet TK-801R User manual

TK-801R/TK-1601R
8-Port/16-Port Rack Mount KVM Switch
Quick Installation Guide
Guide d'installation rapide du
Switch KVM rackable de 8 Ports/ 16 Ports
Anleitung zur Schnellinstallation des
8-Port/16-Port Rack Mount KVM Switch
Guia de Instalacion Rdpida
Switch KVM Montable en Rack de 8/16 Puertos
Version 07.23.04
TRENDnet
TRENDware, USA
What's Next in Networking
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.

Table of Contents
English . 1
1. Prepare for Installation . 1
2. Introduction . 2
3. Product Detail. 3
4. Hardware Installation . 4
5. Operation . 5
6. Specifications . 8
Troubleshooting . 9

English QIG
1. Prepare for Installation
Thank you for purchasing TRENDnet's TK-801R or TK-1601R KVM Switch.
This guide will help you set up your KVM switch. Following the installation
instructions should be quick and easy. If you run into problems, please refer to
the Troubleshooting section. If you need further technical support, please visit
www.TRENDNET.com or call technical support by phone.
Verify Package Contents
Please make sure you have everything in the box:
TK-801Ror TK-1601R Quick In:
stallation Guide
Rack-mount kit
4 »
AC Power Adapter
The TK-801R 8-Port orTK-1601R 16-port PS/2 KVM Switch is compatible with
virtually all computers and operating systems. You only need to have one
monitor, one PS/2 keyboard, one PS/2 mouse, and a KVM cable for each PC.
1
English

2. Introduction
The TK-801R or TK-1601R is a PS/2 KVM Switch that allows you to control 8
or 16 computers respectively using a single monitor, PS/2 keyboard, and PS/2
mouse. By using this KVM Switch, you will cut hardware costs, save valuable
space, and reduce energy consumption.
Hardware Support
The TK-801 R or TK-1601R KVM Switch is compatible with virtually all PS/2
keyboard and mice, including Microsoft Intellimouse, Microsoft Optical Mouse,
and Logitech Net Mouse.
Software Support
The TK-801 R KVM Switch does not require any drivers or software. It is
compatible with the following operating systems: Windows
98/ME/2000/XP/2003 Server, Linux, and Netware.
Plug-N-Play and Hot-Pluggable
The TK-801 R or TK-1601R KVM Switch connects to your computers via PS/2
interface for convenient Plug-and-Play functionality and hot-pluggability.
Front-panel buttons and Hot-Key Commands
You can use the front-panel push buttons or Hot-Key commands to switch
between your computers quickly and easily.
With rich features such as Hot-Pluggability, Auto-Scan, and Hot-Key operation,
TRENDnet's TK-801 R or TK-1601R KVM Switch is the ideal solution for
managing multiple PCs.
2
English

3. Product Detail
Front Panel of TK-801R
Rear Panel of TK-801R
Front Panel ofTK-1601R
Rear Panel of TK-1601R
3
English

4. Hardware Installation
1. T urn off both computers and their peripherals, and disconnect all power
cords.
NOTE: If you would like to mount the KVM switch on the EIA19”
equipment rack, install the included mounting brackets to the sides of
the KVM switch, secure them with the screws, and then mount the KVM
switch to the rack with the hardware provided by the rack manufacturer.
2. Connect the shared keyboard, monitor, and mouse to their respective ports
on the KVM switch. The KVM Switch's inputs are color-coded for your
convenience.
3. Connect the KVM cables to each computer's video, PS/2, and mouse
connectors.
4. Connect the included AC Power Adapter to the KVM switch and to the power
outlet.
5. Turn on the connected computers one-by-one. After the computers boot up
completely, you may begin operating the KVM switch. Installation is now
complete.
POWER
NOTE: Do not switch the PC port (i.e. Do not press the push button of
the KVM switch or enter a "Hot-Key" command) while the computers are
booting up.
English

5. Operation
To switch between computers, you use the front-panel push buttons or hot-key
commands.
The Push Buttons
Press the push button to change the ports.
LED Indication:
Red LED light: KVM cable is connected, PC is powering the KVM switch.
Green LED light: The selected PC port in Active (On Line).
Green LED flash: The selected PC port is in scan-mode or is not being
powered by the PC.
5
English

To switch between computers, you use the front-panel push buttons or hot-key
commands.
Hot-Key Commands
A keyboard hot-key command consists of three keystrokes:
Hot-Key command = ScrLk + ScrLk + Command key(s)
After pressing the ScrLk key, you have 2 seconds to press the ScrLk key again.
You then have another 2 seconds to press a command key. If you do not press
a key within 2 seconds, the switch will exit hot-key mode.
Below are the “Hot-Key” commands for TK-801R or TK-1601R:
ScrLk J
1+
ScrLk J
+
♦ J
Previous Port
ScrLk
+
' ScrLk |
+
Next Port
NOTE: You can also press up arrow key or down arrow key longer time
to speed up selecting the destination port
6
English

To select specific PC port:
ScrLk ] j + ScrLk )
Port No.
1~8 (8 port)
W__J
ScrLk ) + ScrLk ) + f B ] = Beeper
-J -. —,$ l 1
On
NOTE: The default Beeper functions OFF.
( ~ \
Scan
ScrLk ] + ScrLk +
j ^ N
l +
Interval
i
CD CD
Auto
Scan
Mode
To cancel out of Auto Scan Mode, press any key or SPACE bar.
ScrLk ]
l +
ScrLk ]
i +
LendJ
Reset The KVM
Switch
Below are additional "Hot-Key” commands for TK-1601R:
To select a specific PC port:
Select PC = ScrLk ) f ScrLk ] f Y) ( Z )
k- ) \ - ) \ - ) \ - J
Note: (xz) = 2-digit port number
(Port number 01 ~ 16)
For example, to select port 7 on the 16-port KVM Switch TK-1601 R, you would
use the following sequence for the port number 07:
Select PC = [ ScrLk ] f ScrLk ) ( 0 ] f 7
v J v> J v J \
(Port number 07)
7
English

6. Specifications
Computer Connections:
8 for TK-801R or 16 for TK-1601R
Console Port
Connectors:
1 x PS/2 keyboard 6-pin mini din female
1 x PS/2 mouse 6-pin mini din female
1 x VGA HDB15 (15-pin) female
PC Port Connectors:
8 x PS/2 keyboard 6-pin mini din female for TK-801R
8 x PS/2 mouse 6-pin mini din female for TK-801 R
8 x VGA HDB15 (15-pin) female for TK-801 R
16 x PS/2 keyboard 6-pin mini din female for TK-1601R
16 x PS/2 mouse 6-pin mini din female for TK-1601R
16 x VGA HDB15 (15-pin) female for TK-1601R
VGA Resolution:
1920x 1440
Port Selection: Push Button and Hot-Key Commands
LED Segment:
Two LED indicators per port (PC Link (green) and
PC Active (red))
Keyboard State:
Saved and restored
Auto-Scan Intervals:
5 ~ 90 seconds
Power Type:
PS/2 Interface Power
External AC Power Adapter, 12V DC, 1A
(or 9V DC, 1A)
Size (19” Rack Mount): 1RU for TK-801 R, 2RU for TK-1601R
Dimensions:
410 x 165x45 mm (16.14 x 6.5 x 1.77 inches)
for TK-801 R, 406.0 x 163.5 x 85.0 mm (15.98 x 6.44
x3.35 inches) for TK-1601R
Weight:
Approx. 2.20 Kg. (4.85 lbs) for TK-801 R
Approx. 2.65 Kg. (5.85 lbs) for TK-1601R
Operating Temperature:
0° ~ 40°C (32° -104° F)
Storage Temperature:
-20° ~ 60°C (-4° ~ 140° F)
Humidity:
0%~90%, Non-Condensing
Certifications:
FCC and CE
8
English

Troubleshooting
Q1: Do I need to use the included external AC adapter?
A1 : It is recommended that you use the included external power supply
with the TK-801R or TK-1601R KVM switch. You can use either a 9V or
12V DC power adapter with 1A output.
Q2: Can I connect and disconnect the PS/2 cables while the computers
are turned on?
A2: Yes, you can connect or disconnect the PS/2 cables while the
computers are turned on because the KVM switch is Plug-and-Play and
Hot-Pluggable.
Q3: Will the KVM switch restore the keyboard settings when switching
between computers?
A3: Yes, the KVM switch will restore the keyboard settings between
computers such as Cap lock, Num key, etc.
Q4: How do I switch from one computer to another with the KVM switch?
A4: You can switch PCs by pressing the Push button on the KVM switch
or by using the Hot-Key commands.
If you have further questions, please contact Trendware's Technical Support
Department.
Contact Technical Support
Telephone: [phone]
Fax: [phone]
Website: www.TRENDNET.com
E-mail: [email protected]
Technical Support Hours
7:00AM ~ 6:00PM, Monday through Friday
Pacific Standard Time (except holidays)
9
English

TRENDnet
/
TRENDware, USA
What's Next in Networking
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDware’s website at http://www.TRENDNET.com
TRENDware International, Inc.
3135 Kashiwa Street
Torrance, CA 90505
V
http://www.TRENDNET.com
Copyright ©2004. All Rights Reserved. TRENDware International, Inc.