TRQ VEGA Series User manual

Self Contained Emergency Luminary
SERIE VEGA
Characteristics:
Supply 230 V 50/60Hz.
Non maintained Luminary.
Stand by and re-start via Telemando.
Yellow Led indicating battery charging.
Autonomy more than 1 or 3 hours.(depending on the model).
Grade IP22.
Simple connection by means of 6 or 8 mm.cable.
Overload and end of battery discharge protection.
Class II Luminaries should be installed in a way that no metal piece exposed is in electrical
contact with any part of electrical installation connected to ground.
Norms Applied:
CE as per directives 79/23 of LVD and 89/336 of EMC.
Manufactured according to norms UNE-EN 60598-2-22,UNE 20-392-93 and in complying with
the norms EN-55015 and EN 50082-1 of electromagnetic compatibility.
Adapted to the Instructions of low tension electro technical norm RBT and NBE CPI 96 of the
basic norm of edification.
Technical Drawing:
Talleres Radioeléctricos Querol, S.L.
F
IP223

Modelos Available:
Models Emergency Lamp
E
Indicating lamp
S Battery
Auton omy φ
Lumens
EF S-70 6W (G5) LED AMBAR 10mm 2,4V 1,5Ah 1 Hr 102
EF S-180 6W (G5) LED AMBAR 10mm 3,6V 1,5Ah 1 Hr 125
EF S-250 6W (G5) LED AMBAR 10mm 4,8V 1,5Ah 1 Hr 185
EF S-380 PL-11W (2G7) LED AMBAR 10mm 6V 1,5Ah 1 Hr 305
EF S-73 6W (G5) LED AMBAR 10mm (2,4V1,6Ah)X2 3 Hr 70
EF S-55 6W (G5) LED AMBAR 10mm 2,4V 1,5Ah 1 Hr 65
PC-180 6W 6 W 3,6V 1,5Ah 1 Hr. 125
Installation:
Install & connect the luminary to the main supply.
Check that the Green Led indicator indicating the Charging process is lit.
The Batteries are supplied Discharged and they need 24 hours to be charged completely, so
the Luminary will not respond to its Autonomy until 24 hours..
Maintenance:
The batteries should be changed once their duration gets inferior to the assigned.
The luminaries should be checked at least once a year.
The batteries and tubes should be re-cycled or eliminated in an adequate way.
Verification TEST:
Verification test is possible with one of the following Accessories:
TELEMANDO VERIFICATION TV
By pressing the button ON of the telemando, the luminary starts working on emergency mode
in the presence of power (see connection diagram next page).
TELEMANDO TM:
By pressing the button ON, the Luminary starts working on Emergency in the presence of
power.
Stand by position:
Connect the TELEMANDO TM as indicate din the Diagram of connection
En Emergency stage it is possible to Switch OFFF the luminary to save the battery power by
pressing OF. By pressing ON the Luminary starts working again.

Accessories:
ST-21
Clips ST-21 (to recess in the ceiling).
.
ST-25
Double sided Diffuser.

Installation:
Remove the cover by pressing one of the sides.
After removing the cover, take out the upper part of the reflector and you will see the connectors
for making the connection.
Connection ModelsEFS-70, EFS-55, EFS-180, EFS-250, EFS-380,EFS-73
Connection Model PC-180

Cut & introduce the cable according to the indications and make connection of the connectors.
Mounting on the Wall
The holes in the wall to fix the emergency light should be 180mm.
False Ceiling mounting
Make a hole in the false ceiling as per the dimensions indicated.
Attach the accessory ST-21 in their respective holes indicated in the figure above.
Introduce the Emergency unit as indicated in the figure.
Connection Diagram:
Models EFS-70, EFS-55, EFS-180, EFS-250, EFS-380,EFS-73
Model PC-180
The cable used for the installation should be of 4 conductors (2 for the main line and 2 for
telemando).