olympia electronics GR-290/WP User manual

Page 1 from 5
GENERAL
o
These devices are used indoors (ta 40 C) in
places where emergency luminaires are
needed. The luminaires GR-290/WP and GR-
292/WP are suitable for corridors lighting and
the GR-291/WP and GR-293/WP for open
a r e a l i g h t i n g . E a c h d e v i c e m u s t b e
permanently connected to mains power
supply. In normal operation the battery is
charging. In case of a mains power supply
failure the device will light the illumination
led automatically in emergency mode. When
the mains power supply is restored the
device turns to normal operation.
INSTALLATION
To install the luminaire follow the installation
instructions οn page 2.
Battery Charging
The battery charging is completely controlled.
In this case, is achieved the perfect battery
maintenance , as well as the elongation of its
duration. When the battery has completely
charged, it charges with a maintenance
current.
Battery Cut-off
The device in this operation when the mains
power supply fails and battery has lost its
energy. During this operation the device
enters the idle state and battery consumption
is negligible, in order to be protected from
deep discharge.
Automatic Operational Test
It is conducted automatically every 15 days. In
order to be performed, the mains power
supply and the battery should be connected.
Automatic Autonomous Test
The Automatic Autonomous Test is conducted
and measures the device’s back up operation
and emergency duration. The BATTERY
FAULT LED blinks during the measurement,
indicating this process to the user. This test is
conducted automatically every six months. In
order to be performed, the mains power
supply and the battery should be connected
and fully charged. If the battery is not fully
charged, the test is postponed until the battery
is completely charged. If during this test, the
autonomy is less than the nominal then the
battery fault led turned on continuously and
the battery must be replaced.
Back Up Operation
The autonomous duration of battery during
emergency mode is at least the one that is
WATERPROOF SELF TESTING NON MAINTAINED SPOT LIGHT
EMERGENCY LUMINAIRES WITH 1 WHITE POWER LED
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
EXTERNAL DIMENSION
WEIGHT
GUARANTEE
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-MH)
CHARGE TIME
INDICATIONS - CONTROLS
BATTERY PROTECTION
MINIMUM DURATION
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
EMERGENCY ILLUMINATION
LIGHT SOURCE
220-240V AC / 50-60Hz
3 hours1.5 hour
24 hours
Deep discharge and overcharge protection
IP65
4.8V/1.2Ah
270lm 160lm
1 white power LED
o
5 to 40 C
Up to 95%
ABS/PC, PC
3 years (1 year for the battery)
430gr.
Ø125 x 65 mm
EN 60598-1, EN 60598-2-22, ΕΝ 55015, ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
Charge, lamp fault, battery fault, TEST button
GR-290/WP GR-291/WP GR-292/WP GR-293/WP
3.7W / 4.1 VA
TECHNICAL CHARACTERISTICS (for LED MODULE specifications see page 4)
Thank you for your trust in our products
Olympia Electronics - European manufacturer
923293005_09_004

Page 2 from 5
stated in the list of the technical
characteristics. During emergency mode, a
light source test is also performed.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance
or testing must be done by authorized
personnel only.
2. The device must be connected to the
ma i n s p o we r s up p l y t h roug h a fu s e
dependent by the total amount of the line’s
power load.
3. The replacement of the battery and the
light source must be done using parts of the
same type, by the manufacturer or by a
competent person.
4. In case of inactive use for a period greater
than 2 months, disconnect the battery by
pulling out the battery’s connector.
5. I s not allowed to discard batteries t i
into common trash bins, they must
b e d i s c a r d e d o n l y i n b a t t e r y
recycling points. Do not incinerate.
The light source contained in this
luminaire shall only be replaced by the
manufacturer, or his agent, or a similar
qualified person.
NOTE! The light source is non-user
replaceable.
3
Initial installation
1 Untighten the screw and pull up the reflector.
2 Always use in any case round mains cable, with a diameter of 5-10mm (H05RN-F type 2x1mm²
or any other type, at least equal to it’s mechanical and electrical properties). ATTENTION!!
The cable must not be deformed in any way (This requirement is important to ensure the ΙΡ
rating). Install the included gaskets in to the cable entry holes (verify that are not deformed). Make a
hole in the center by using a small screwdriver. Pass the round cable through the gasket. Detach the
power terminal, connect the wires as shown in the picture and attach the power terminal (10A max).
3 Place the battery’s connector to the corresponding connector on the P.C.B.
4 Refit the reflector (mind the correct orientation), tighten the screw securely and the luminaire is ready
for mounting.
NOTE!! After finishing the installation you must power the luminaire for, at least, 24 hours for
battery charging to perform the nominal autonomy.
2
Cable
entry
hole L
N
1
INSTALLATION INSTRUCTIONS
923293005_09_004

Page 3 from 5
Set up the lamp to the suspended ceiling as it is shown bellow (Required opening 110mm):
Step 1
Bend the springs, to get into the hole of the suspended ceiling, as you can see to the next figure.
Step 2
Push up the luminaire, as shown in figure 2.
Step 3
Continue to push upwards until the lamp locks.
If you want to pull off the device, put a flat blade
screwdriver, between the device and the ceiling.
Figure 2
Figure 3
Figure 1
Ø110mm
Step 1. Follow the step 1 of the installation instructions.
Step 2. Unfasten the retaining screw (Figure 4) and detach the part for suspended ceiling
installation.
Step 3. Drill 2 holes on the base using a 4mm drill bit in order to permit the retaining screws to pass.
Mark these two drilled points on the required mounting location, drill the holes and install the supplied
plastic plugs. ATTENTION!! Especially for the GR-290/WP and GR-292/WP luminaires installation on
the ceiling you must align the base with the indications on the luminaire’s base (Figure 5).
Step 4. WARNING!! To preserve the ΙΡ 65 rating, fit the screws with the metallic washer and
plastic ring which are included. Next use the screw to fasten the unit to the surface .(Figure 6)
Step 5. Install the decorative rim (package included). Next, use the 2 fasteners to install the unit to
the require location.
Step 5. Follow the step 3 of the installation instructions.
Figure 6
SURFACE MOUNTING
MOUNTING THE LAMP IN SUSPENDED CEILING
Figure 4 Figure 5
Retaining fastener
Drill here
Indications
923293005_09_004

Page 4 from 5
Lamp fault
indication LED
GR-290/WP, GR-292/WP
GR-291/WP, GR-293/WP
ATTENTION!!!
During installation follow this light direction.
Corridor
lighting
Open
area
lighting
Important notice for the installed luminaires in one area !!!
The installer must connect the battery’s connector first and then should power the luminaire.
The time between batteries connection must be, at least 1.5 minute.
With this variation, it is ensured that the non synchronized Automatic Autonomous Test for
two or more luminaires installed in one area, is not conducted in the same day.
Battery replacement.
It can be done only by a competent person and after the mains interruption.
1. Remove the luminaire from the suspended ceiling (figure 3).
2. Follow the step 1 of the installation instructions.
3. Disconnect the connector and remove the old battery.
4. Connect the new battery with the same type (step 2 of the installation instructions) and place it in
the position of the old one.
5. Replace the removed parts (step 1 and 4) and power the device.
FAULT
LAMP
CHARGE
BATT.
FAULT
LAMP
CHARGE
BATT.
96
65
125
FAULT
LAMP
CHARGE
BATT.
FAULT
LAMP
CHARGE
BATT.
Battery
fault
indication
LED
Battery
charge
indication
LED
Figure 4
LED MODULE CHARACTERISTICS
Manufacturer
Model Number
Voltage Range
Connections
Nominal Power
Temperature (tc)
Olympia Electronics S.A
60 °C max. across the board 45 °C max. across the board
Non reversible connection between main pcb and led module
3-3.2VDC
2.2W 1.1W
1110143 2704143
GR-290/WP GR-291/WP GR-292/WP GR-293/WP
Status of LEDs
LEDs Description of indication
CHARGE : Battery charging, : battery charged, : disconnected or unfunctional battery
LAMP FAULT : Operation check, : lamp fault, : normal operation
BATT. FAULT : Autonomy test, : battery fault, : normal operation
Note : Blinking, : constantly on, : off
CAUTION : Do not view directly with bare eyes.
923293005_09_004

TEST
FAULT
LAMPCHARGE BATT.
Page 5 from 5
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
0: Non maintained (*)
A: Including test device
90: 1.5 hour duration
180: 3 hours duration
(*) Non Maintained operation: The luminaire lights its illumination source, only in power
supply’s failure.
Maintained operation: The luminaire lights its illumination source, when it is powered by the
mains power supply or not.
WARRANTY
Olympia Electronics guarantees the quality, condition and operation of the goods. The period of warranty
is specified in the official catalogue of Olympia Electronics and also in the technical leaflet, which
accompanies each product. This warranty ceases to exist if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics or if the buyer modifies the goods
provided or has any repairs or re-setting done by a third party, unless Olympia Electronics has fully
agreed to them in writing. Products that have been damaged can be returned to the premises of our
company for repair or replacement, as long as the warranty period is valid.
Olympia Electronics reserves the right to repair or to replace the returned goods and to or not charge the
buyer depending on the reason of defection. Olympia Electronics reserves the right to charge or not the
buyer the transportation cost.
HEAD OFFICE
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.gr
[email protected]
923293005_09_004