Trust SPYC@M 300 User manual

Trust SPYC@M 300
UK
TRUST SPYC@M 300
User’s Manual
Version 1.0

TRUST SPYC@M 300
01 UK 12440 SPYC@M 300 CD HANDLEIDING (A4)
Thank you
Thank you very much for purchasing this product from the Trust range. We wish you hours of fun
with it. Please read this manual carefully before using the product.
Registration
Register your purchase now at the Trust Internet site, www.trust.com, so that you are able to
receive optimal guarantee and service support. You will be automatically informed of
developments to your product and of other Trust products. You will also have the chance to win
some spectacular prizes.
Copyright statement
No part of this instruction manual may be reproduced or transmitted, in any form or by any means,
electronic or mechanical, including photocopying, recording, or information storage and retrieval
systems, for any purpose other than the purchaser's own personal use, without prior written
permission from the manufacturer.
Disclaimer statement
The manufacturer specifically disclaims all warranties, either express or implied, including, but not
limited to, implied warranties for the marketability and suitability for a particular purpose, with
respect to the software, the accompanying product manual(s) and written material, and all other
accompanying hardware. The manufacturer reserves the right to revise or make improvements to
its product at any time and without obligation to notify any person of such revisions or
improvements.
In no event shall the manufacturer be liable for any consequential or incidental damages, including
any loss of business profits or any other commercial damages, arising out of the use of its
products.
All company or product names are trademarks or registered trademarks of their respective
owners.

TRUST SPYC@M 300
1
UK
Table of Contents
1. Introduction ..................................................................................................................................... 3
1.1 Conventions used in this manual........................................................................................... 3
1.2 Contents of the package.......................................................................................................... 3
1.3 Minimum system requirements .............................................................................................. 3
2. Safety................................................................................................................................................ 4
2.1 General ...................................................................................................................................... 4
2.2 Batteries .................................................................................................................................... 4
3. Functions of the ‘Trust SpyC@m 300’ .......................................................................................... 5
3.1 Camera functions ..................................................................................................................... 5
3.2 LCD display Functions ............................................................................................................ 5
4. Installation ....................................................................................................................................... 6
4.1 Inserting batteries .................................................................................................................... 6
4.2 ‘Trust SpyC@m 300’ setup program installation .................................................................. 6
5. Software Installation ....................................................................................................................... 8
5.1 Installing Ulead Photo Express 3.0 SE................................................................................... 8
5.2 Ulead Photo Explorer 6.0 installation................................................................................... 10
5.3 Installing COOL 360 ............................................................................................................... 12
5.4 VideoLive Mail 4.0 installation ..............................................................................................14
5.5 Installation Microsoft Internet Explorer (NetMeeting) ........................................................ 15
5.6 Ulead VideoStudio 3.0 SE installation.................................................................................. 16
6. Using the camera .......................................................................................................................... 21
6.1 Connecting cables ................................................................................................................. 21
6.2 Taking photos......................................................................................................................... 21
6.3 Menu options .......................................................................................................................... 21
6.3.1 Programming photo quality ........................................................................................... 21
6.3.2 Using the automatic shutter release ............................................................................. 21
6.3.3 Erasing photos ................................................................................................................ 21
6.3.4 Repeat function ............................................................................................................... 22
6.3.5 Viewing photos in the computer.................................................................................... 22
6.3.6 WebCam & Internet ......................................................................................................... 22
7. Using the Software........................................................................................................................ 23
7.1 SpyC@m Manager.................................................................................................................. 23
7.1.1 Photos and Soundclips .................................................................................................. 23
7.1.2 Video................................................................................................................................. 24
7.2 Using Ulead PhotoExpress 3.0 SE........................................................................................ 25
7.2.1 Loading photos ............................................................................................................... 25

TRUST SPYC@M 300
2
7.2.2 Live video images ........................................................................................................... 28
7.3 Using Ulead Photo Explorer.................................................................................................. 28
7.4 Using VideoLive Mail ............................................................................................................. 29
7.4.1 One-time setting .............................................................................................................. 29
7.4.2 Working with VideoLive Mail Plus ................................................................................. 34
7.4.3 Function key description................................................................................................ 35
7.4.4 Creating a VideoMail .......................................................................................................36
7.5 Using Ulead COOL 360 .......................................................................................................... 37
8. Troubleshooting............................................................................................................................ 38
9. Specifications ................................................................................................................................ 40
10. Trust Customer Care Centres ...................................................................................................... 41
Italian Office................................................................................................................................... 41
French Office ................................................................................................................................. 41
German Office................................................................................................................................ 41
Spanish Office ............................................................................................................................... 41
Dutch Office................................................................................................................................... 41
European Head Office................................................................................................................... 41

TRUST SPYC@M 300
3
UK
1. Introduction
This instruction manual is intended for users of the Trust SpyC@m 300. Prior knowledge is necessary to
install and use this product. If you have any questions, please consult one of the Trust Customer Care
Centres. You can find more information about these Customer Care Centres on the last page of this
electronic manual, as well as at the back of the quick installation manual.
1.1 Conventions used in this manual
The following conventions have been used in this manual to indicate instructions:
<key> Here you should press a key. The name of the key is given between brackets.
‘System’ This is a specific term used in a program. These are the terms used by, for example,
Microsoft Windows 98.
[DIR] Key in the text shown in square brackets [….].
{term} The text between the parentheses {….} is the English term, e.g. {File} used in the figure
referred to.
Additional information will be shown as follows:
NOTE: If you connect the ‘Trust SpyC@m 300’ to a USB HUB, then the USB HUB should have its own
power supply.
The examples assume that the letter “D” has been assigned to your CD-ROM drive. If your system uses a
different drive letter for your CD-ROM drive, for example “E”, you should replace “D” by “E”.
1.2 Contents of the package
Please check the contents of the package before reading the instruction manual. It should contain the
following:
•Trust SpyC@m 300
•Camera stand
•Clip stand
•USB cable
•2 type AAA alkaline batteries
•CD-ROM with setup program and applications
•CD-ROM with Ulead VIDEO STUDIO SE
•Wrist band
If anything is missing or damaged, please contact one of the Trust Care Centres. You can find more
information at the back of this instruction manual.
1.3 Minimum system requirements
•Intel Pentium 200 MMX CPU or higher
•USB port
•Windows 98 / ME / 2000
•32 MB RAM (64 MB recommended)
•60 MB free Hard disk space
•4X CD-ROM player

TRUST SPYC@M 300
4
Recommended system configuration for full operation of the programs:
•ISDN-adapter or modem
•Sound card with speakers and microphone
•Internet subscription
2. Safety
2.1 General
1. Do not use the device in a damp environment.
2. Do not try to repair the device yourself.
3. Under the following circumstances have the device repaired by qualified personnel:
a) The cable or plug is damaged or worn.
b) Liquid has entered the device.
c) The device has fallen and/or the casing has been damaged.
4. Position the device so that the cables cannot be damaged.
2.2 Batteries
1. The batteries are not rechargeable. Do not try to recharge these batteries. This may cause danger of
explosion.
2. Do not throw the batteries into an open fire. The batteries may explode.
3. Never drill into the batteries.
4. Keep the batteries out of the reach of small children.
When the batteries are empty, ask your local government where you can recycle them.
NOTE: If the battery voltage is low or empty, all pictures you intend to save must first be loaded into the
computer and saved before you replace the batteries. When the batteries are being replaced, all
photos disappear from the memory of the camera.
NOTE: Do not mix old and new batteries because the old batteries may drain the new ones.
NOTE: If the camera is not used for an extended period, you must remove the batteries from the camera
to save the battery capacity.

TRUST SPYC@M 300
5
UK
3. Functions of the ‘Trust SpyC@m 300’
3.1 Camera functions
Figure 1: ‘Trust SpyC@m 300’ functions
A Viewer E Shutter release
B Lens F LCD screen
C ON / OFF & Menu
button
G Battery cover
D USB connection
Table 1: SpyC@m 300 functions
3.2 LCD display Functions
DISPLAY Description Function
High resolution High (VGA) resolution for
taking photos in 640x480.
Low resolution Low (QVGA) resolution for
taking photos in 320x240.
Repeat mode This option lets you take
several photos consecutively.
Automatic shutter release This option lets you switch on
the automatic shutter release.
Erase This option lets you erase the
photos in the camera.
Table 2: LCD display functions

TRUST SPYC@M 300
6
4. Installation
4.1 Inserting batteries
Insert the batteries in your camera as follows.
Figure 2: Inserting batteries
1. Slide the battery cover on the back of the camera to the left as indicated in Figure 2.
2. Insert the batteries in the compartment as indicated. You can also read on the inside of the battery
compartment how the batteries must be inserted.
3. Next, close the battery cover.
Note: Inserting the batteries incorrectly causes damage.
Note: Replace the battery only with an equivalent type (2x AAA type) batteries or rechargeable NiMH
Note: If the camera is not used for an extended period, you must remove the batteries from the camera
to save the battery capacity.
4.2 ‘Trust SpyC@m 300’ setup program installation
1. Insert the CD in the PC and the installation program will start up automatically. If this does not occur, start
up ‘Setup.exe’ on the CD-ROM. Figure 3 will appear.
Figure 3: setup program installation

TRUST SPYC@M 300
7
UK
2. Click on ‘TRUST SpyC@m 300’ to start up installation. Figure 4 will appear.
Figure 4: setup program installation
3. Click on ‘Next’ to start installation. After installation, Figure 5 will appear.
Figure 5: setup program installation
4. Click on ‘OK’ to complete installation and restart the computer.
5. Connect the USB connection D(see Figure 1) of the camera to a free USB port of your computer.
Windows 98 detects the new hardware and automatically installs the Trust SpyC@m 300 setup program.
You have completed installation of the setup program. Proceed to chapter 5 for installation of the software
enclosed.

TRUST SPYC@M 300
8
5. Software Installation
5.1 Installing Ulead Photo Express 3.0 SE
Ulead Photo Express 3.0 SE is an image editor that you can use to load and edit the images on your
computer that you have taken using your SpyC@m 300. Follow the instructions below to install Ulead Photo
Express 3.0 SE.
1. In the installation screen, click on 'Install Ulead Photo Express 3.0 SE'. See figure 2. Figure 6 will
appear.
Figure 6: Installing Ulead Photo Express 3.0 SE
2. Click on ‘Install’. Figure 7 will appear.
Figure 7: Installing Ulead Photo Express 3.0 SE

TRUST SPYC@M 300
9
UK
3. Click on 'Next'. Figure 8 will appear.
Figure 8: Installing Ulead Photo Express 3.0 SE
4. Click on 'Yes' to accept the license agreement and continue with the installation. Figure 9 will appear.
Figure 9: Installing Ulead Photo Express 3.0 SE
5. Click on 'Next'. Figure 10 will appear.
Figure 10: Installing Ulead Photo Express 3.0 SE

TRUST SPYC@M 300
10
6. Click on ‘Typical’. Follow the directions on the screen. After installation, Figure 11 will appear.
Figure 11: Installing Ulead Photo Express 3.0 SE
7. Disable the option for 'online' registration and click on 'Finish'. Figure 12 will appear.
Figure 12: Installing Ulead Photo Express 3.0 SE
8. Click on 'Finish' to restart your computer.
You have now completed the installation of Ulead Photo Express 3.0 SE. See chapter 5.2 for installation of
Ulead Photo Explorer 6.0.
5.2 Ulead Photo Explorer 6.0 installation
Ulead Photo Explorer 6 is an image-processing program that enables you to load and process photos you
have taken with your SpyC@m 300 on the PC. For installation of Ulead Photo Explorer 6 follow the
instructions below.
1. Go to the installation screen and click on ‘Install Ulead Photo Express 3.0 SE. See Figure 2. Figure 13
will appear.

TRUST SPYC@M 300
11
UK
Figure 13: Ulead Photo Explorer 6.0 installation
2. Click on ‘Next’. Figure 14 will appear
Figure 14: Ulead Photo Explorer 6.0 installation
3. Press ‘YES” to accept the licence agreement and proceed. Figure 15 will appear.
Figure 15: Ulead Photo Explorer 6.0 installation
4. Enter your data and click on ‘Next’. Follow the directions on the screen. After installation, Figure 16 will
appear.

TRUST SPYC@M 300
12
Figure 16: Ulead Photo Explorer 6.0 installation
5. Disable the ‘I would like to launch Ulead Photo Explorer’ option and click on ‘Finish” to complete
installation.
You have completed installation of Ulead Photo Explorer 6.0 SE. See chapter 4.5 for installation of Ulead
Cool 360.
5.3 Installing COOL 360
Ulead COOL 360 is an image-processing program that lets you change various photos you took with your
SpyC@m 300 into Panorama photos. Follow the instructions below for installation of COOL 360. See Figure
3.
1. Go to the installation screen and click on ‘Install COOL 360. Figure 17 will appear.
Figure 17: Ulead COOL 360 installation
2. Click on ‘Next’. Figure 18 will appear.

TRUST SPYC@M 300
13
UK
Figure 18: Ulead COOL 360 installation
3. Press ‘YES” to accept licensing and to continue. Follow the instructions on the screen. During installation,
Figure 19 will appear.
Figure 19: Ulead COOL 360 installation
4. Click on ‘Yes’ and a screen similar to Figure 20 will appear.
Figure 20: Ulead COOL 360 installation
5. Switch on the option to register the application ‘online’ and click on ‘Finish”.
You have completed installation of Ulead COOL360. See chapter 5.4 for installation of VideoLive Mail 4.0

TRUST SPYC@M 300
14
5.4 VideoLive Mail 4.0 installation
VideoLive Mail 4.0 lets you send a video and audio multi-media e-mail. To use this application, you must
have a modem or an ISDN device, a sound card with speakers and microphone and an internet subscription.
Follow the instructions below for installation of VideoLive Mail
1. On the installation screen, click on ‘Install VideoLiveMail’ See Figure 3. Figure 21 will appear.
Figure 21: VideoLive Mail installation
2. Click on ‘Next’. Figure 22 will appear.
Figure 22: VideoLive Mail Plus installation
3. Click on ‘Yes’ to accept licensing and continue with the installation. Follow the directions on the screen.
During installation, Figure 23 will appear.

TRUST SPYC@M 300
15
UK
Figure 23: VideoLive Mail Plus installation
4. Enter your name, Company and the CD-Key. You can find the CD-key on the sleeve of your CD. Press
‘Next’. Follow the directions on the screen.
NOTE: If you leave the ‘Company’ box blank, installation will be terminated. Always fill in this box
5. After installation, Figure 24 will appear.
Figure 24: VideoLive Mail Plus installation
6. Click on ‘Finish’ to complete installation.
You have completed installation of VideoLive Mail Plus. See chapter 5.5 for installation of Microsoft
Internet Explorer (NetMeeting)
5.5 Installation Microsoft Internet Explorer (NetMeeting)
Microsoft Internet Explorer is a program with various applications for internet use, such as a web browser and
an e-mail program (Outlook Express). The application ‘NetMeeting’ is also included in Internet Explorer.
Microsoft NetMeeting lets you communicate with friends, colleagues and others by image and sound. For this
application you must have a modem or an ISDN device, a sound card with speakers and microphone and an
internet subscription. The program is included on the Software disc.
For installation of Netmeeting, click on ‘MICROSOFT NETMEETING’ in Figure 1.
After installation you can read the Netmeeting manual. Proceed with chapter 5.6 for installation of Ulead
VideoStudio 3.0 SE.

TRUST SPYC@M 300
16
5.6 Ulead VideoStudio 3.0 SE installation
Ulead VideoStudio 3.0 SE is a program.
The Video Studio program is enclosed in a separate CD-ROM. Follow the instructions below for installation:
1. Insert the VideoStudio CD-ROM in your CD-ROM player.
2. If the CD does not start up automatically, proceed as follows
3. Click on ‘Run’ in the Start menu. Figure 25 will appear.
Figure 25: VideoStudio 3.0 SE installation
4. Select the language you want and click on ‘OK’. Figure 26 will appear.
Figure 26: VideoStudio 3.0 SE installation
5. Click on ‘Next’. Figure 27 will appear.

TRUST SPYC@M 300
17
UK
Figure 27: VideoStudio 3.0 SE installation
6. Press ‘YES” to accept licensing and to continue. Follow the instructions on the screen. During installation,
Figure 28 will appear.
Figure 28: VideoStudio 3.0 SE installation
7. Switch on both options for installation of the program components and click on ‘Next’. Follow the
instructions on the screen. During installation Figure 29 will appear.
Figure 29: VideoStudio 3.0 SE installation

TRUST SPYC@M 300
18
8. Click on ‘Yes’ to accept the license agreement and to continue. Follow the instructions on the screen.
During installation of the NetShow component, Figure 30 will appear.
Figure 30: VideoStudio 3.0 SE (NetShow) installation
9. Select ‘Complete Installation’ and click on ‘Next’. Follow the instructions on the screen.
10. After installation of the NetShow component, Figure 31 will appear.
Figure 31: VideoStudio 3.0 SE (NetShow) installation
11. Click on ‘Ok’ to complete installation of the NetShow component. Figure 32 will appear.