Trynex SnowEx SP-1575 User manual

1© Trynex International 2013
(REV A) F50872
SP-1575
Serial # N1-161813 and higher
SP-1875
Serial # D1-613020 and higher
Madison Heights, Michigan 48071
800-725-8377
www.snowexproducts.com
CUSTOMER COPY
This Manual Must Be Read Before Operating The Equipment
Owner’s Manual

© Trynex International 2011 (REV A) F508722
Table of Contents
General Information ...................................................................................................................................................................................... 3
Introduction ................................................................................................................................................................................................. 4
Safety .......................................................................................................................................................................................................... 5
Warning Decal Position .................................................................................................................................................................................. 6
Spreader Assembly........................................................................................................................................................................................ 7
Operating the Spreader ................................................................................................................................................................................ 8
Spreader Maintenance ................................................................................................................................................................................. 9
General Wiring Instructions ........................................................................................................................................................................ 10
Control and Harness Diagram ............................................................................................................................................................... 11-13
Trobleshooting ...................................................................................................................................................................................... 14-15
Warranty .................................................................................................................................................................................................... 16
Side and Bottom View
Model # SP-1575/SP-1875.......................................................................................................................................................... 17
Hopper Assembly Parts Breakdown
Model # SP-1575.................................................................................................................................................................... 18-19
Frame Assembly Parts Breakdown
Model # SP-1575.................................................................................................................................................................... 20-21
Hitch Parts Breakdown
Model # SP-1575.................................................................................................................................................................... 22-23
Hopper Assembly Parts Breakdown
Model # SP-1875.................................................................................................................................................................... 24-25
Frame Assembly Parts Breakdown
Model # SP-1875.....................................................................................................................................................................26-27
Notes .................................................................................................................................................................................................... 28-29
Have a question or need assistance?
SnowEx Customer Care
1-800-SALTERS
or [phone]
Monday through Friday 8:00 AM to 4:30 PM EST
Fax: [phone]
E-mail: [e-mail]
Website: www.snowexproducts.com

3© Trynex International 2011 (REV A) F50872
General Information
CONGRATULATIONS!
The spreader you have purchased is an example of snow and ice control technology at its nest! Your spreader’s self-contained design is a
trademark of all SnowEx products. Here’s why…
SIMPLICITY: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx spreader.
RELIABILITY: High impact linear low density polyethelyne hopper. State-of-the-art electronic dual variable speed control, custom engineered
powder coated frame, maximum torque 12-volt motor coupled to a custom engineered transmission; found only on SnowEx products.
VERSATILITY: Multi-use capabilities allows spreading of a variety of materials for snow and ice control.
WARRANTY: Best in the industry, hands down! 2 years standard and now 5 year extended (optional).
The benets you are about to recognize are that of time, money and effort.
We welcome you to the world of SnowEx Performance.
Registration
Record the following information in this manual for quick reference.
Spreader Model Number
Spreader Serial Number Controller Serial Number
Date of Purchase
Dealer Where Purchased
When ordering Parts, the above information is necessary. This will help to see that you
receive the correct parts.
At the right is a diagram of the ID tag. This tag on the spreader is located on the frame.
Please ll out the warranty card with all the necessary information to validate it.
This will also give us a record so that any safety or service information can be
communicated to you.
Madison Heights, MI 48071
U.S.A.
1-800-725-8377
www.trynexfactory.com
Model No.
SP-1575
N1-000000
Serial No.
D6381_TrynEx_CE_sprdr_plate4in x 2.3125in
Madison Heights, MI 48071
U.S.A.
1-800-725-8377
www.trynexfactory.com
Model No.
SP-1875
D1-000000
Serial No.
D6267_TrynEx_CE_sprdr_plate4in x 2.3125in

© Trynex International 2011 (REV A) F508724
Introduction
This manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and use of this spreader.
Refer to the table of contents for an outline of this manual.
We require that you read and understand the contents of this manual completely (especially all safety information) before attempting any
procedure contained herein.
THIS SIGN SHOULD ALERT YOU:
The Society of Automotive Engineers has adopted this SAFETY ALERT SYMBOL to pinpoint characteristics
that, if NOT carefully followed, can create a safety hazard. When you see this symbol in this manual or on the
machine itself, BE ALERT! Your personal safety and the safety of others is involved.
Dened below are the SAFETY ALERT messages and how they will appear in this manual:
(RED)
Information that, if not carefully followed,
can cause death!
(ORANGE)
Information that, if not carefully followed,
can cause serious personal injury or death!
(YELLOW)
Information that, if not carefully followed,
can cause minor injury or damage to equipment

5© Trynex International 2011 (REV A) F50872
Safety
Before attempting any procedure in this book, these safety instructions must be read and understood by all workers who have any part in the
preparation or use of this equipment.
For your safety warning and information decals have been placed on this product to remind the operator of safety precautions . If anything
happens to mark or destroy the decals, please request new ones from SnowEx.
Never exceed the Gross Vehicle Weight Rating of vehicle. Failure to do so may limit a vehicles handling
characteristics.
Never attempt to take a unit off a truck with material in it.
Always keep hands, feet, and clothing away from power driven parts.
Unit must be pinned and locked into position before operating vehicle.
Always shut off vehicle and power source before attempting to attach or detach or service unit Be sure
vehicle/power source is properly braked or chocked.
Remember, most accidents are preventable and caused by human error. Exercising of care and precautions
must be observed to prevent the possibility of injury to operator or others!
Never operate equipment when under the inuence of alcohol, drugs, or medications that might alter your
judgment and/or reaction time.
Before working with the spreader, secure all loose tting clothing and unrestrained hair.
Always wear safety glasses with side shields when servicing spreader. Failure to do this could result in
serious injury to the eyes.
Never allow children to operate or climb on equipment.
Always check areas to be spread to be sure no hazardous conditions or substances are in the area.
Always inspect unit for defects: broken, worn or bent parts, weakened areas on spreader.
Remember it is the owner’s responsibility to communicate information on safe usage and proper
maintenance of all equipment.
Always make sure personnel are clear of areas of danger when using equipment.
Never weld or grind on equipment without having a re extinguisher available.
Inspect the unit periodically for defects. Parts that are broken, missing or worn out must be replaced
immediately. The unit or any part of it can not be altered without prior written permission from the
manufacturer.
Always inspect pins and latches whenever attaching or detaching spreader, and before operation of spreader.
Never exceed 45 m.p.h. when loaded spreader is attached to vehicle. Braking distances may be increased
and handling characteristics may be impaired at speeds above 45 m.p.h.
Never use wet materials or materials with foreign debris with any of these spreaders. These units are
designed to handle dry, clean, free owing material.
Never leave material in hopper for long periods of time. Be aware that all ice melters are hygroscopic and will
attract atmospheric moisture and harden up.

© Trynex International 2011 (REV A) F508726
Warning Decal Positions
Model # SP-1575/SP-1875
D6192_Warning.ai4in x 2.25in
D6194_Warning.ai4in x 2.25in
ROTATING AUGER CAN CAUSE
SERIOUS INJURY OR DEATH
• Keep arms, hands, and loose clothing
away from auger.
• Shut off control and unplug spreader
before servicing.
D6335
7.25in w x 3.00in h
D6335_Warning.ai

7© Trynex International 2011 (REV A) F50872
Spreader Assembly
Model # SP-1575
Assembly Instructions
Note: Your spreader is factory set in the Three Point Mount position.
To switch your spreader to truck mount remove hitch and rotate 180 degrees and reattach..
Three Point Mount Position
Truck Mount Position

© Trynex International 2011 (REV A) F508728
Operating the Spreader
Model # SP-1575/SP-1875
SPREADER LOADING
WARNING – Do not overload vehicle. Use chart below to calculate weight of material. Weights of material are an average for dry
materials.
Material Weight Per Cubic Ft.
Rock Salt 80-90 lbs.
Sand/Salt Mix 95-120 lbs.
• Warning – Never leave material in hopper for long periods of time as salt is hygroscopic and will attract atmospheric moisture and harden up.
When spreading sand mix, a 1:1 ratio for Sand/Salt mix is recommended to prevent the material from freezing.
SPREADER OPERATION
• The Dual Variable Speed Controller has dual nger-tip dials for maximum performance, digital system status with warning protection and built-
in Vibrator Switch.
• To start, press power switch on controller and spreader will accelerate to speed set on spinner and auger dials.
• To stop, press power on controller to off position.
• Speed of Auger and Spinner may be adjusted separately to get desired ow and spread distance
• The Vibrator Switch is needed for dense material or to increase the ow to the Auger. This eliminates bridging of material in hopper.
• A Material Bafe has been installed in your spreader to stop ne material from free owing. If using dense or damp material, or if more ow is
desired, remove Material Bafe. However, it is recommended that the Material Bafe remain in place if using bulk salt.
• It is important that the Inverted Vee not be removed except when servicing.
• If there are any problems while operating the spreader, refer to Troubleshooting Guide.
SPREADING TIPS
• Spread ice melters with the storm to prevent unmanageable levels of ice.
• Never exceed 10 m.p.h. when spreading.
• For a wider pass, increase spinner speed.
• For a heavier pass, drive slower or increase auger speed.
• Never operate spreader near pedestrians.
• Calculate spread pattern when near vegetation.
LICENSE PLATE INSTALLATION (IF REQUIRED BY LOCAL LAWS)
You will need (2) 1/4-20 X 1/2” machine screws along with nylock type nuts
(not included with spreader)
Install license plate with hardware to mounting holes provided in
hopper apron (see illustration)
Mounting Holes

9© Trynex International 2011 (REV A) F50872
Spreader Maintenance
Model # SP-1575/SP-1875
• WARNING – When servicing is necessary, perform it in a protected area Do not use power tools in rain or snow because of danger of electrical
shock or injury. Keep area well lighted. Use proper tools. Keep the area of service clean to help avoid accidents.
• WARNING: Never remove spreader with material in hopper.
• WARNING: Disconnect electricity to spreader before servicing.
• CAUTION: – When replacing parts use only original manufacturer”s parts. Failure to do so will void warranty.
• CAUTION: – The controller is a solid state electronic unit and is not serviceable. Any attempt to service will void warranty.
• CAUTION: - There are no serviceable parts in the motor/transmission assembly. Any attempt to service will void warranty.
• CAUTION: - Spinner motor is not designed for continuous duty. Allow motor to cool between long cycle times.
• CAUTION: – When pressure washing motor enclosure area, stay at least 36’’ away from motor enclosures.
• ATTENTION: Store control in cool dry place during the off season.
• Use dielectric grease on all electrical connections to prevent corrosion at the beginning and end of the season and each time power plugs are
disconnected.
• Wash unit after each use to prevent material build-up and corrosion.
• Paint or oil all bare metal surfaces at the end of the season.
• Apply small amount of light oil to latches as needed.
• If motor cover is removed for any reason, use silicone sealant to ensure weather proong of enclosure.
• After rst use, tighten all nuts and bolts on spreader and mount.

© Trynex International 2011 (REV A) F5087210
General Wiring Instructions
Model # SP-1575/SP-1875
Step 1: Take harness assembly and route from the rear of the vehicle to the front. Route harness along frame and attach to frame holes and
frame supports. It is not recommended to attach to fuel or brake lines for obvious reasons. Do not route close to exhaust system or engine, even
though Snowex uses high temperature wiring, it still could melt under extreme heat and short the spreader electrical system, as well as the
vehicle electrical system.
Step 2: Mount rear plug on bumper using supplied bolts, locate towards the center of the bumper to reduce the amount of debris the tires will
throw to the rear. Important: Apply a small amount of dielectric grease to the plug. Also try to mount so plug faces upward to help keep plugs
tightly sealed.
Step 3: Secure harness from the rear to the front using heavy duty ty-wraps or frame clips along the frame and lighter duty ty-wraps everywhere
else.
Step 4: Layout harness portion that connects to the battery along the re wall and fender well. Do not connect power leads to battery yet. Drill
a 3/4” hole in the re wall, or use existing access hole, for the control portion of the harness and route connector and harness through hole.
Be sure to check the area on the other side of the re wall to make sure you are not going to dri ll into the vehicle harness or a control module.
Generally you can drill on either side of the steering wheel for a good location.
Step 5: Connect harness to the back of the controller and mount to a suitable location. NOTE: You may want to contact customer before mounting
controller, some prefer not to have holes drilled into the dashboard. Ty-wrap loose controller harness and move to the engine compartment. Do
not mount close to any heater vents.
Step 6: Connect power leads to the battery: Red + Positive, Black – Negative, always connect to the primary battery if using a dual battery
system, secure loose loom to any other large or medium vehicle harness with medium duty ty-wraps; this will secure wiring harness.
Step 7: Push the ON/OFF button on the controller to check for power, when that has been conrmed turn power OFF. The electrical portion of the
installation is complete.
NOTE: If adding an inline fuse use a 60 amp slow blow (time delay) or a 60 amp relay.

11© Trynex International 2011 (REV A) F50872
Control and Harness Diagram
Model # SP-1575/SP-1875
Key Part No. Description Qty
1 D6527 Spreader Control | Pro 1
2 D6124 Bracket Knob 2
3 D6329 Controller Mounting Bracket | Pro 1
4 D6341 Control Power Cable | 156" Pro 1
5 D6322 Vehicle Harness | 311" 1
6 D6321 Spreader Harness | 38" 1
7 D6343 Dust Cover | Pro 1
8 D6170 Connector Adapter | 6" Anderson 1
9 D6237 Power Switch | 5 Terminal 1
10 D6354 Vibrator Switch | 3 Terminal Red 1
11 D6344 Dielectric Grease | 1-1/2 oz. 1
IMPORTANT: In the off season remove control
and put in a cool dry place. The interior summer
temperatures could damage circuit board and
void warranty.
To Vibrator
To Auger Motor
To Spinner Motor
5
2
1
4
3
6
7
8
910
IMPORTANT: Do Not modify harness length. Any modications
will void warranty.
Special Notes:
1) All external connections must have dielectric grease.
2) Read lead labels before attaching to power source or ground.
3) No other devices may be spliced into wiring harness.
4) Any repairs to wiring harness must be done with heat shrink butt
connectors.
5) If inline fuse is installed, use a 60 amp maxi fuse or circuit breaker.

© Trynex International 2011 (REV A) F5087212
Harness Diagram
Model # SP-1575/SP-1875
Red
Black
End View
Red
10 GA
Auger+
White
10 GA
Spinner+
Green
10 GA
Auger -
Orange
10 GA
Vibrator -
Hot
Circuit
Spinner+
10 GA White
Auger+
10 GA Red
Vibrator+
12 GA Orange
Spinner-
10 GA Black
Auger-
10 GA Green
Vibrator-
12 GA Blue
Grd
Circuit
Black
10 GA
Spinner -
Blue
12 GA
Vibrator -
Mold Cap
Black
3/8” Terminal w/Heat Shrink
124” Tubing
Front View
Black to
Negative -
Red to
Positive +
Red
D6322 Vehicle Harness
D6341 Control Power Cable

13© Trynex International 2011 (REV A) F50872
Harness Diagram
Model # SP-1575/SP-1875
Spinner Red
Vibrator
Auger
Spinner
Auger Red
Vibrator Red
Black
Black
Black
Red Leads Female
Black Leads Male
D6321 Spreader Harness
D6527 Controller
Black
Negative (-)
Red
Positive (+)
Vibrator
Red Positive (+)
Spinner
Red Positive (+)
Auger
Red Positive (+)
Vibrator
Black Negative (-)
Spinner
Black Negative (-)
Auger
Black Negative (-)

© Trynex International 2011 (REV A) F5087214
Troubleshooting
Model # SP-1575/SP-1875
Spreader
Does Not Run
Controller Turns On
Beeps Shuts Off
Displays Error Code
On/Off Switch
Lights No Display
Nothing Happens
No Display
On/Off Will Not Light Up
OL Code
E1 Code
LB Code
All Other Codes
EO Code
Check Input Power
Check Power Source
To Controller
Denition
Amp Draw
Too High
Denition
Dead Short
In Motor Circuit
Denition
Bad Electrical
Connection
Check Harness
For Spliced In
Accessory
Denition
Open Circuit Between
Motor And Controller
Bad Controller
Check With Test Kit
Low Battery
Less Than 12 Volt
Output
Bad Controller
Check With Test KIt
Jammed Material
Corrosion
Break In
Wiring Harness
Check With Test Kit
Replace Affected
Components
Bad Motor
Check With Test Kit
Bad Controller
Check With Test Kit
Corrosion
Bad Controller
Check With Test Kit
Spreader Unplugged
Loose Connection
Bad Transmission
Check With Test Kit
Motor Power Cord
Disconnected
Inside Drive Assembly
Load Test Battery
Switch Off & On
For Auto-Reverse
Function Clear Jam
Replace All
Corroded
Connections
Replace Harness
Test 4 to 20 Amp Draw
No Load Good
Replace All Corroded
Connections
Replace
20+ Amp Draw
No Load Bad
Plug In Spreader
Tighten Or Replace
Test Turn Shaft
By Hand
Should Turn Freely
Open Access Cover
And Plug Together
Don´t Forget
Use Doelectric
Grease
Snowex Diagnostic Test Kit (STK-080) Is Available To Accurately Diagnose Any Issues With Snowex Spreaders.
Call Your Dealer For Details.

15© Trynex International 2011 (REV A) F50872
Troubleshooting Material Flow
Model # SP-1575/SP-1875
Snowex Diagnostic Test Kit (STK-080) Is Available To Accurately Diagnose Any Issues With Snowex Spreaders.
Call Your Dealer For Details.
Material Does Not Flow
Material Free Flows
Slow Material Flow
Material Obstruction
Increase Auger Speed
Auger Runs Backwards
Material Issue
Check Bafe Length
Turn On Vibrator
Check Bafe Position
Turn On Vibrator
Remove Obstruction
Run 12 Volt To Auger
Circuit On Spreader
Power Cord
18” Correct
Should Touch Hopper
On 3 Sides
Material Issue
Auger Runs Proper
Direction
Material Issue
Auger Runs
Backwards
Material Issue
Replace Vehicle
Harness
Check Connections
At Auger Motor For
Reverse Polarity
Polarity Correct
ReplaceSpreader
Harness

© Trynex International 2011 (REV A) F5087216
Warranty
L1185 © Trynex International 2009
5 — 38
Warranty
Limited Warranty
Snowex products are warranted for a period of two years from the date of purchase against
defects in material or workmanship under normal use and service, subject to limitations detailed
below. Warranty period of two years begins on the date of purchase by the original retail user.
TheWARRANTY REGISTRATION CARD must be returned to the manufacturer for this warranty
to become eective. This warranty applies to the original retail purchaser only. This warranty does
not cover damages caused by improper installation, misuse, lack of proper maintenance, alterations
or repairs made by anyone other than authorized Snowex dealers or Snowex personnel. Due to the
corrosive properties of the materials dispensed by spreaders, Trynex does not warrant against
damage caused by corrosion. Warranty claims by the user must be made to the dealer from where
the product was purchased, unless otherwise authorized by Snowex. Snowex reserves the right to
determine if any part is defective and to repair or replace such parts as it elects. This warranty does
not cover shipping costs of defective parts to or from the dealer.
LIMITATION OF LIABILITY
Neither Snowex, nor any company aliated with it, makes any warranties, representations for
promise as to the performance or quality other than what is herein contained. The liability of Snowex
to the purchaser for damages arising out of the manufacture, sale, delivery, use or resale of this
spreader shall be limited to and shall not exceed the costs of repair or replacement of defective
parts. Snowex shall not be liable for loss of use, inconvenience or any other incidental, indirect or
consequential damages, so the above limitations on incidental or consequential damages may not
apply to you.
NO DEALER HAS AUTHORITY TO MAKE ANY REPRESENTATION OR PROMISE ON BEHALF OF
SNOWEX, OR TO ALTER OR MODIFY THE TERMS OR LIMITATIONS OF THIS
WARRANTY IN ANY WAY.

© Trynex International 2011 (REV A) F5087217
Spreader Views
Model # SP-1575/SP-1875
SP-1575
SP-1875

© Trynex International 2011 (REV A) F5087218
Hopper Assembly Parts Breakdown
Model # SP-1575
7
17
6
10
16
12
20
14
2
1
21
11
3
19
8
4
13
18
5
9
15

19© Trynex International 2011 (REV A) F50872
Hopper Assembly Parts Breakdown
Model # SP-1575
BOM ID
Description
Qty
1
D4122
4
2
D5100
1
3
D5105
1
4
D5110
1
5
D5114
1
6
D5115
1
BOM ID
Description
Qty
7
D5706
4
8
D6105
2
9
D6137
2
10
D6140
1
11
D6165
4
12
D6166
4
BOM ID
Description
Qty
13
D6169
6
14
D6174
1
15
D6198
2
16
D6240
1
17
D6257
1
18
D6394
2
BOM ID
Description
Qty
19
D6553
6
20
D6584
8
21
D6978
4

© Trynex International 2011 (REV A) F5087220
Frame Assembly Parts Breakdown
Model # SP-1575
20
23
23
25
27
3
10
26
18
15
8
14
21
22
4
17
1
19
12
16
5
11
6
9
13
2
7
24