Trynex SnowEx V-MAXX SP-2400 H Owner's manual

© Trynex International 2008 (REV000) L1215 MAXXH — 1
Owner / Operator’s Manual
This Manual Must Be Read Before Operating The Equipment
CUSTOMER COPY
Madison Heights, Michigan 48071
800-725-8377
Protected by the following patents, #6,089,478, #6,088,865, #Des.425,915
and other pending U.S. and foreign patent applications.
See Back Page for Details!
Warm Up to
with a
Winter Hat!
F R E E
F R E E
SP-2400 H
SP-9500 H
SP-8500 H
Equipment for Snow & Ice Control
V-MAXX SPREADERS

© Trynex International 2008 L1215
MAXXH — 2
Table of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
General Information and Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 7
Spreader Assembly and Exploded Views. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 29
Blank Pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 - 53
Have a question or need assistance?
SnowEx Customer Service
[phone]
or [phone]
Monday through Friday 8:00 AM to 4:30 PM EST
Fax: [phone]
E-Mail: [email protected]
Website: www.snowexproducts.com
Electrical System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 - 36
Spreader Mounting System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 - 43
Spreader Operating Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 - 46
Troubleshooting Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 - 48
Spreader Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Determine Vehicle Payload Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 - 55
Hydraulic Hose Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 - 38
Hydraulic System Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

© Trynex International 2008 L1215 MAXXH — 3
Introduction
This manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and
use of this spreader. Refer to the table of contents for an outline of this manual.
We require that you read and understand the contents of this manual completely (especially all safety information)
attempting any procedure contained herein.
THIS SIGN SHOULD ALERT YOU:
The Society of Automotive Engineers has adopted this SAFETY ALERT SYMBOL to pinpoint characteristics
that, if NOT carefully followed, can create a safety hazard. When you see this symbol in this manual or on the
machine itself, BE ALERT! Your personal safety and the safety of others is involved
.
Dened below are the SAFETY ALERT messages and how they will appear in this manual:
(RED)
Information that, if not carefully followed,
can cause death!
(ORANGE)
Information that, if not carefully followed,
can cause serious personal injury or death!
(YELLOW)
Information that, if not carefully followed,
can cause minor injury or damage to equipment.

© Trynex International 2008 L1215
MAXXH — 4
General Information
CONGRATULATIONS!
The spreader you have purchased is an example of snow and ice control technology at its nest! Your spreader’s innovative,
self-contained design is a trademark of all Trynex products. Here’s why...
SIMPLICITY: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx spreader.
RELIABILITY: High impact linear low density polyethelyne hopper, heavy duty hydraulic motors,
custom engineered powder coated frame, found only on SnowEx products.
VERSATILITY: Multi-use capabilities allows spreading of a variety of materials for snow and ice control.
WARRANTY: Best in the industry, hands down! 2 Years Standard.
The benets you are about to recognize are that of time, money and eort.
Wewelcome you to the world of Trynex Performance.
Registration
Record the following information in this manual for quick reference.
Spreader Model Number _____________________________________________________________________________________
Spreader Serial Number________________________________ Controller Serial Number _______________________________
Date of Purchase___________________________________________________________________________________________
Dealer Where Purchased _____________________________________________________________________________________
When ordering parts, the above information is necessary. This will help to insure
that you receive the correct parts.
At the right is a diagram of the ID tag. This tag on the spreader is located
on the frame.
Please ll out the warranty card with all the necessary information to validate it. This will also give us a record so that
any safety or service information may be communicated to you.
SER. NO.______________________
TRYNEX INTERNATIONAL
Warren, MI 48089 [phone]

© Trynex International 2008 L1215 MAXXH— 5
Safety
Before attempting any procedure in this book, these safety instructions must be read and understood by all workers who
have any part in the preparation or use of this equipment.
For your safety warning and information decals have been placed on this product to remind the operator of safety precautions.
If anything happens to mark or destroy the decals, please request new ones from Trynex, International.
Unit must be strapped down and locked into position before operating vehicle.
Never exceed the Gross Vehicle Weight Rating of vehicle. Failure to do so may limit a vehicles
handling characteristics.
Never attempt to take a unit o a truck with material in it.
Never exceed 45 m.p.h. when loaded spreader is attached to vehicle. Braking distances may be
increased and handling characteristics may be impaired at speeds above 45 m.p.h.
Never allow children to operate or climb on equipment.
Always check areasto be spread to be sure no hazardous conditions or substances are in the area.
Always inspect unit for defects:broken, worn or bent parts, weakened areas on spreader or mount.
Always shut o vehicle and power source before attempting to attach or detach or service spreader
unit. Be sure vehicle/power source is properly braked or chocked.
Always keep hands, feet, and clothing away from power-driven parts. Remember it is the owner’s
responsibility to communicate information on safe usage and proper maintenance of all equipment.
Always make sure personnel are clear of areas of danger when using equipment. Maintain 60'
distance from all bystanders when operating the spreader.
Inspect the unit periodically for defects. Parts that are broken, missing, or worn out must be replaced
immediately. The unit, or any part of it should be altered without prior written permission from the
manufacturer.
Never use V-Maxx 8500 with foreign debris in the spreader. These units are designed to handle clean,
free-owing material. Note: Can not spread water softner salt.

© Trynex International 2008 L1215
MAXXH — 6
Safety
(continued)
Always inspect pins and latches whenever attaching or detaching spreader, and before traveling.
Never leave material in hopper for long periods of time. Be aware that all ice melters are hygroscopic
and will attract atmospheric moisture and harden up.
Remember, most accidents are preventable and caused by human error. Exercising of care and
precautions must be observed to prevent the possibility of injury to operator or others!
Never operate equipment when under the inuence of alcohol, drugs, or medication that might alter
your judgment and/or reaction time.
Before working with the spreader, secure all loose tting clothing and unrestrained hair.
Always wear safety glasses with side shields when servicing spreader. Failure to do this could result in
serious injury to the eyes.
CHMSL light must be installed and plugged in to meet DOT FMVSS-108 standards.
Always disconnect the spreader hydraulic hoses from there power source before servicing
the unit. Failure to do so could result in serious injury.
Make sure hydraulic couplers are fully connected, failure to do so will result in motor failure.

© Trynex International 2008 L1215 MAXXH — 7
Safety and Warning Labels
D 6546
D 6548
D 6335
D 6544
D 6545
D 6859
SERIAL NUMBER
ON REVERSE SIDE
V-Maxx 9500 shown for reference only,
these warning decals will be on all V-Maxx
series spreaders. Some locations will be
dierent on the SP-2400 tailgate spreader.

© Trynex International 2008 L1215
MAXXH — 8
V-Maxx 8500H/9500H Auger Drive Assembly
Parts Breakdown

© Trynex International 2008 L1215 MAXXH — 9
.ytQ
noitpircseD
.oNtraPyeK
2D 5768 Hydraulic Bulkhead Fitting
2
1/2-13 Serrated Flange Nut
D 6874 1/4” x 1.5 SS Self Drilling Screw
6
D 5759
2
xeH"4/3x02-"4/1
D 5764 SP-8500 64” Hydraulic Hose
2
daeHxeHdetarreS31-"2/1
D 5770 Hose Clamp
1D 5787 Motor Coupling Shield
8D 6452
2
revoCgniraeB
D 5767 Hydraulic Motor Hose Coupling
1D 5758 Auger Motor Coupler
26873D
1D 5776 Hytrel Spyder
16842 Auger CouplerD
2 D 6845 Auger Bearing
1 D 6816 SP-8500 Auger Weldment
4D 6528
1
kcotSyeK"61/3
1D 5760 Hydraulic Auger Motor
4 D 6584 3/8” Serrated Flange Nut
4
" Serrated Flange1x61-"8/3
D 5761 Hydraulic Motor Mount
V-Maxx 8500H/9500H Auger Drive Assembly
Parts Breakdown
2D 5535
1D 6814
2D 6132
1Hose Fitting Mounting Bracket
D 5769 Bulkhead Fitting Jam Nut
D
1SP-9500 80” Auger Weldment6897
D 5779
2SP-9500 96” Hydraulic Hose
D 6881
1SP-9500 Rear Rail Assembly
D 6803 SP-8500 Rear Rail Assembly

© Trynex International 2008 L1215
MAXXH — 10
V-Maxx 2400H Auger Drive Assembly
Parts Breakdown
NOTE: Hoses are shown for reference only
and are not included with the system.

© Trynex International 2008 L1215 MAXXH — 11
.ytQ
noitpircseD
.oNtraPyeK
2D 5527 1” Bearing
4
D 6453 5/16” x 1” Serrated 18-8 SS
3
1D 5702 Bearing Cover
1D 5783 6” Auger Weldment
4D 5706 5/16” Serrated Flange Nut
4D 6452
1D 6825 Woodru Key
1D 5754 Auger Motor Mounting Bracket
15760D
2D 5767 Hydraulic Hose Coupler
Hydraulic Auger Motor
1D 5749 1/4” Key Stock
1 D 5776 Urethane Spyder
2
3/8” Serrated HHCS
D 5775 Motor Coupler
V-Maxx 2400H Auger Drive Assembly
Parts Breakdown
D 6584 3/8” Flange Nut

L1215 © Trynex International 2008
MAXXH — 12
V-Maxx 8500H Spinner Drive Assembly
Parts Breakdown
NOTE: Hoses are shown for reference only
and are not included with the system.

© Trynex International 2008 L1215 MAXXH — 13
V-Maxx 8500H Spinner Drive Assembly
Parts Breakdown
.ytQnoitpircseD.oNtraPyeK
2D 5767 Hydraulic Hose Coupler
1D 5755 Hydraulic Spinner Motor
1D 5764
4D 6462
4D 6452 3/8-16 x 1” Serrated Hex Head Bolt
2D 4124 3/8 Nylock Nut
1D 5784 Hydraulic Motor To Spinner Coupler
2D 6160 3/8 - 16 x 2” Hex Head Bolt
3D 6854 1/4 - 20 x 1” Serrated HWH SS
1D 6823
8D 6138 5/16 Nylock Nut
4D 6462 5/16-18 x 1-3/4” Hex Head Bolt
1D 5762 Spinner Hub Weldment
5D 4289 1/4-20 Nylock Nut
1D 6820 Heavy Duty Tubular Guard
1D 6833
4D 6165 5/16 Flat Washer
2
D 6132 1/4-20 x 1/2” SS HWH Serrated TCS
tloB"/43-1x81-61/5
rennipSenahterUetilF5
e 1tuhClairetaM
rotcelfeDlairetaM
duorhSerusolcnEevirD
D 6832
2 D 6563 20” Drive Mounting Pin
Drive Mounting Pin Clip
D 4135 1

L1215 © Trynex International 2008
MAXXH — 14
V-Maxx 9500H Spinner Drive Assembly
Parts Breakdown
NOTE: Hoses are shown for reference only
and are not included with the system.

© Trynex International 2008 L1215 MAXXH — 15
V-Maxx 9500H Spinner Drive Assembly
Parts Breakdown
.ytQnoitpircseD.oNtraPyeK
2D 5767 Hydraulic Hose Coupler
1D 5755 Hydraulic Spinner Motor
1D 5764
8D 6462
4D 6452 3/8-16 x 1” Serrated Hex Head Bolt
2D 4124 3/8 Nylock Nut
1D 5784 Hydraulic Motor To Spinner Coupler
2D 6160 3/8 - 16 x 2” Hex Head Bolt
3D 6854 1/4 - 20 x 1” Serrated HWH SS
1D 6823
8D 6138 5/16 Nylock Nut
1 D 5762 Spinner Hub Weldment
7 D 4289 1/4-20 Nylock Nut
1 D 6820 Heavy Duty Tubular Guard
1
D 6858
4
D 6165 5/16 Flat Washer
1
D 6132 1/4-20 x 1/2” SS HWH Serrated TCS
" Hex Head Bolt/43-1x81-61/5
rennipSenahterUetilF5
e 1tuhClairetaM
duorhSerusolcnEevirD
D 6885
1
D 5777
1
D 6563
7
D 4135 Drive Pin Mounting Clip
20” Drive Mounting Pin
10” Drop Extension
Plastic Push Pin
Drive Extension Spinner Shield
rotcelfeDlairetaM
D 6463
1
D 6859 1

L1215 © Trynex International 2008
MAXXH — 16
V-Maxx 2400H Spinner Drive Assembly
Parts Breakdown
NOTE: Hoses are shown for reference only
and are not included with the system.

© Trynex International 2008 L1215 MAXXH — 17
V-Maxx 2400H Spinner Drive Assembly
Parts Breakdown
.ytQnoitpircseD.oNtraPyeK
3D 6854 1/4-20 x 1” HWH Serrated
1D 6823 Urethane Spinner
1D 5718
1D 6133
1D 6327 Spinner Deector
2D 4121 3/8-16 x 1” HHCS
1D 5744 Spinner Motor Enclosure
4D 4135 5/16 Hair Pin Clip
1D 5739 Spinner Drive Pin
1D 5741
1D 5740 Short Leveler Rod
2D 6447 5/16” x 1” Self Driller
1D 5738 Leveler Mount Bracket
1D 5755 Hydraulic Spinner Motor
2
2
D 4124
3
D 4125 3/8 Flat Washer
D 4289 1/4-20 Nylock Nut
5/16-18 x 1/2” Hex Bolt
Long Leveler Rod
3/8-16 x 1” Serrated Hex Head Bolt 4
3/8-16 Nylock Nut
Spinner Hub Weldment
D 5767 Hydraulic Hose Coupling 2
D 6452

© Trynex International 2008 L1215
MAXXH — 18
V-Maxx 8500H Hopper Assembly
Parts Breakdown

© Trynex International 2008 L1215 MAXXH — 19
V-Maxx 8500H Hopper Assembly
Parts Breakdown
.ytQnoitpircseD.oNtraPyeK
15/16-18 x 1-1/4 HHCS6576D
713/8 Serrated Flange Nut4856D
16165D
01tuNkcolyN"61/58316D
D 6874 #14 1-1/2” Tek w/Neo Washer 2
83/8-16 x 1-1/2” Hex Head Bolt4122D
1rotarbiVytuDyvaeH5156D
1reppoHxxaM-V0086D
1ylbmessAVdetrevnI8086D
1elffaBegrahcsiD7086D
41186D
1
setalPgnikcaBVdetrevnI
D
1
Front Top Screen
8486
6849D
6rellirDfleSHWH"5.1x41#4786D
Rear Top Screen
Flat Washer"61/5
26866D
2D 4134
Top Screen Hinge Pin
Top Screen Hinge Pin Clip

© Trynex International 2008 L1215
MAXXH — 20
V-Maxx 9500H Hopper Assembly
Parts Breakdown