TSS Monolift User manual

Monolift

Read all safety warnings, instructions and
illustrations provided for this piece of strength
equipment. Failure to follow all instructions listed
below may result in serious injury or death. User assumes all potential
risks of assembly or use of this product. The assembly of this piece of
equipment requires 4 people.
PERSONAL SAFETY
●Stay alert, watch what you are doing when assembling and operating the
strength equipment. Do not use the strength equipment while you are
tired or under the influence of drugs, alcohol or medication. A moment
of inattention while operating or assembling the strength equipment may
result in serious or fatal injury.
EQUIPMENT USE AND CARE
●Visually inspect all components in order to identify potential
deformation or damage. If damages are observed, discontinue assembly
and contact the manufacturer at [email protected],
[email protected].
●Multiple components involved with assembly of this piece of strength
equipment are above 50lbs and it is recommended that you have an
additional person to assist in the positioning of these items.
●Ensure that all components are securely fastened before use.
1

Required Tools
●Crescent Wrench
●1 ⅛” and 9/16” Socket and Wrench
Parts
MONO-001 |(x1) |Part A
MONO-002 |(x2) |Part B
MONO-003 |(x1) |Part C
MONO-004 |(x1) |Part D
2

MONO-005 |(x1) |Part E
MONO-006 |(x1) |Part F
MONO-007 |(x1) |Part G
MONO-008 |(x1) |Part H
MONO-009 |(x4) |Part I
MONO-010 |(x1) |Part J
MONO-011 |(x1) |Part K
3

MONO-012 |(x1) |Part L
MONO-013 |(x1) |Part M
MONO-014 |(x1) |Part N
MONO-200 |(x10) |Part O
MONO-300 |(x1) |Part P
¾” x 2” Bolt |(x8) |Part Q
¾” Lock Washer |(x8) |Part R
¾” Nut |(x8) |Part S
⅜” x 1 ¼” Bolt |(x8) |Part T
⅜” Lock Washer |(x8) |Part U
½” x 5 ½” Bolt |(x1) |Part V
½” Lock Nut |(x1) |Part W
4

Height Pin |(x1) |Part X
Cotter Pin |(x5) |Part Y
Band Pegs |(x4) |Part Z
5

Assembly
Place parts A and B as seen
above in image 1.
Parts T and U will be placed as
seen above in image 2 on both
sides of part B and tightened
using a 9/16” socket.
6

Place parts C and D as seen
above in image 3.
Place parts Q, R, and S as seen
above in image 4 to connect both
C and D to part B. Tighten with 1
⅛” socket and crescent wrench.
7

Image 5 and 6 display how parts
H and E are placed and attached
with part Z. Image 7 below
displays how part Z is placed
through both parts E and H.
8

Part F is placed onto part C and is attached with part Z as seen above in
image 8.
9

Place part G onto part D as seen above in image 9.
10

Place part J on part C as seen above in image 10. Part P will then be
used to connect them.
11

Part I is placed on part C as seen above in image 11 and is held in place
with part P.
12

Place part K into part J as seen above in image 12 and connect them both
using part P.
Part M is placed on part K as seen above in image 13. Once placed,
elevate part M until it places pressure onto part F.
13

Place part X into part I at the desired location. Once placed, reduce
pressure from part M until part X is touching part D.
14

Part L is placed onto part E as seen above in image 15.
Part P is then used to connect part L to part E as seen above in image 16.
15

Place part N between parts L and H as seen above in image 17. Place
parts P and Y as seen in image 17 in order to secure part N.
16

Place part Z in the desired location on part A and secure them with part
Y.
17

You have now completed assembling your very own Monolift! Thank
you for choosing Texas Strength Systems for your fitness needs. If you
have any questions, comments, or concerns please don’t hesitate to
contact our staff.
Contact Information
Email: [email protected]
Phone: [phone]
18