ttaf PowerPort User manual

Tel: [phone]
www.power-port.com
Istanbul Caddesi Kavakli Koyu,No.21,Buyukcekmece,lstanbul 34520,Turkey
TTAF Electronic Company Limited
3+5 Port Surge Protector Power Board
PowerPort

Description
The PowerPort is an energy conserving device that automatically detects power
consumption and turn off connected electrical appliances to save standby power
consumption. The PowerPort device is the best choice to help you make the energy
efficient, easy to save money and protect the environment for future generations. The
built-in surge protector inside this device will protect your valuable electrical
equipments from voltage spikes. The EMI/RFI noise filtration eliminates interference
from other electrical devices to improve the performance of connected electrical
appliances. This product does not have a power switch; it is powered on when the power
cord is plugged in and it receives the turn-on control signal from remote.
Features
• Energy Saving Program
Product design is to meet energy efficiency and energy saving goals.
• IR Remote Control
Use your own IR remote control to turn on this PowerPort.
• Loading Current Display
The digital display to show current consumption status.
• Automatically Shut Down
The PowerPort will automatically detect current consumption of connected electrical
appliances. It shuts down the power of switched outlets once these connected
electrical appliances turn into standby model or reach the factory setting of power
saving level.
• Power Surge Protection
Protects your electrical equipments from voltage spikes.
• EMI/RFI Noise Filtration
Eliminates the interference and increases the performance of electrical appliance
• LED Indication
There are three LED to indicate device status (AC Power,Surge Protection, and IR
Status.LEDs to indicate device status - AC Power, Surge Protection, and IR Status.
IR receiver
IR can control the voltage/current/power
IR Control indicator
When the Indicator Light is on,It
means the Grounded Outlets are power on.
LED Display
LED Display shows
the voltage/current/power
Power indicator
If the Power Indicator Light is on It means
the PowerPort is at surge protection mode.
3+5 Port Surge Protector Power Board
Surge Protected High Current Outlets
These outlets provides continuous
power to the device that you plugged in.
Surge Protected Smart Outlets
When the energy consumption of the devices that plugged these
smart outlets decrease as %70 of total consumption The PowerPort
detects this energy consumption decrease and automatically turn itself off.
Surge Protected TV Antenna Ports
The PowerPort also protects your Satellite Receivers
and TVs from surges that can caused by TV Antenna Cable.
The PowerPort has two TV Antenna Set as 1 Input and 1 Output.
RJ45&RJ11 Ports
RJ45&RJ11 Ports are used to protect your PC,
Telephone,DSL Modems and Fax Machine from
surges can caused off voltage picks through
Telephone Line and Internet Line.
USB Ports
You can use USB Ports to charge your
Smartphones,Tablets and USB Powered Devices.
3+5 Port Surge Protector Power Board
PowerPort
Reset Button
If the circuit overload over than
16A the PowerPort turn off.And
by pressing this reset button you
can turn the PowerPort on.
3+5 Port Surge Protector Power Board
PowerPort

Installation
The installation steps are as follows:
1.Connect the electrical appliances to Always On outlet or Switched outlet.
Note: The Always On outlets will provide constant power. The switched outlets will be
controlled by PowerPort and the On or Off will depend on the current consumption
status. Details please refer to specifications.
2.Connect the telephone RJ11 cable, Ethernet Cat 5 RJ45 cable and coaxial cable to
PowerPort for surge protection.
Caution
1. Make sure the power source is properly grounded, then use the power cord supplied
with the PowerPort to connect it to the power source.
2. If your installation requires a different power cord than the one supplied with the
power supply, be sure the cord is adequately sized for the switch's current
requirements. In addition, be sure to use a power cord displaying the mark of the
safety agency that defines the regulations for power cords in your country. The mark is
your assurance that the power cord can be used safely with this product.
Operation
The operation steps are as follows:
1. Plug the power cord into AC power source.
Caution: Make sure the correct operating voltage of PowerPort before connecting it into
AC power source.
2. The current display panel flashes once and the LEDs of Surge Protection, Grounding, and
Always On are lit.
Note: At this moment only the electricity of the Always On outlets are on but the switched
outlets are still off.
3. Use IR remote to turn on the PowerPort. The current display panel and Power LED will be
turned on.
Note: 1. The PowerPort has limited reception frequency range as described in the
Electrical of Specifications. Please consult the service agency of electrical appliance if
your remote can't turn on the PowerPort.
2. Any function keys of IR remote should be able to enable the PowerPort product.
3. The PowerPort product can't be turned off unless unplugs the power cord from AC
power source.
4. The IR LED will flash once when receives the signal.
4. The switched outlets are supplying the power to connected electronic appliances.
5. Turn on the connected electronic appliances.
Note: The current display will show the current consumption of total switched outlets only.
6. The PowerPort will automatically detect variation of total power consumption. If the total
power consumption descends more than 70% of peak loading current for 3 minutes the
PowerPort will be shut down and turned into standby mode.
Note : 1. Details please see the shutdown conditions in the specifications.
2. Only the electricity of switched outlets will be off but the Always On outlets are still on.
7. Repeat the Step 3 to turn on the connected electrical appliances again once the PowerPort
has been turned into standby mode.

Illustrated Diagrams
To Finish Your Program and Save the Power
1
2
3
4
5
To Finish Your Program and Save the Power
All electrical appliances are off.
(Into energy saving mode)
Use IR remote controller to turn on
PowerPort device first.
Use TV's IR remote controller to turn on TV
Use DVD Player's IR remote controller to turn on
DVD Player.
Start enjoying your favorite programs.
Use DVD Player's IR remote controller to turn off
DVD Player.
Use TV's IR remote controller to turn off TV.
Finish the programs.
After 3 minutes the PowerPort will shut down
TV and DVD Player power automatically then turn
itself into standby mode. (Into energy saving model)