Turnstone TS40005EM User manual

Page 1 of 9
TS40005EM Rev C
TS40005EM
Turnstone®Mobile Easel w/Mimio
R
©2001 Steelcase Inc.
Grand Rapids, MI 49501 U.S.A.
Printed in U.S.A.
p
lkret 
sdfgn, ty 
sd oiudfg ui 
dfsgdgs oom gh
1. Unpack panels and parts.
Please check all pieces before beginning this project. This kit
may contain extra screws for your convenience. If there are
problems or discrepancies, call our customer service
department at 1-800-turnstone (1-800-887-6786).
Balloon No. Description Quantity
 1 Markerboard 1
 2 Tackboard 1
 3 Controller 1
 4 Receivers 2
 5 Electronic Pens Black, Red
6  Smart Caps Blue, Green
 7 User Interface 1
 8 User Interface Mounting Plate 1
 9 LH & RH Receiving Cables 1 each
 10 Center Shelf 1
 11 Wire Managers 2
 12 Top Cover 1
 13 Easel Base 1
 14 Easel Hardware 1
 15 Assembly Instructions 1
 16 Power Strip (optional) 1
 17 Power Adaptor 1
 18 Storage Tray 1
 19 Electronic Eraser 1
 20 Top Plate 1

Easel Hardware
Quantity Description
 20 8-18 x .750 pan head sheetmetal screws, zinc
 3 Wire manager routing aids
 2 6-18 x .625 pan head tapping screws
 3 8-18 x .750 pan head sheetmetal screws, black
Part Descriptions

Page 2 of 9
TS40005EM Rev C
List of Materials
4
7
8
1
2
20
3
5
13
10
19
11
12
16
17
18
6
9
14
15

Page 3 of 9
TS40005EM Rev C
2. AttachTop Plate to Panels
With the boards positioned on their sides and user interface cutout
positioned up as shown, using a #2 Phillips screwdriver attach the Top
Plate to the top of the boards using eight (8) 8-18 x .75 sheetmetal
screws. Turn screws until tight.
3. Attach User Interface
Using two (2) 6-32 x .750 screws, gently screw the mounting
plate to the user interface as shown in the figure at right. Do
not over tighten the screws.

Page 4 of 9
TS40005EM Rev C
4. Attach Center Shelf
Place center shelf in location between the panels with flat surface
facing towards the top plate and storage tray cutout opposite the User
Interface. In the order shown, using the prepunched locating holes,
attach Center Shelf to board edges approximately 32 inches below
Top Plate with four (4) 8-18 x .750 sheetmetal screws. Turn screws
until tight.
5. Easel Base Panels
Attach the easel base to the panels using eight (8) 8-18 x
.750 sheetmetal screws as shown. Turn screws until tight.
32"
A
C
D
B

Page 5 of 9
TS40005EM Rev C
6. Attach Receivers
Gently push receivers into the receiver holders. Attach RH and LH
receiver cables to receiver ends and route cable as shown.
7. Connect Cables
Connect the LH and RH receiver cables to the LH and RH terminals
as marked on the controller. Connect the user interface cable to the
controller terminal marked UI.
8. Attach Controller
Using the prepunched locating holes, attach the controller box
approximately 8 inches below the top plate as shown. Mount the
controller box using three (3) 8-18 x .750 sheetmetal screws. Turn
screws until tight.
LH
RH
PRINTER
POWER
USB
RHLHUI
PRINTER
POWER
USB

Page 6 of 9
TS40005EM Rev C
9. Attach Wire Managers
Peel doubleface tape and attach wire managers as shown. Locate
one wire manager directly between the Top Plate circular cutout and
the Center Shelf circular cutout. Center the second wire manager 3
inches below the parallel printer controller terminal. Press firmly to
adhere wire manager to the back of the markeboard. Never attach
Wire Managers to the back of the tackboard. After Wire Managers
have been installed gently push the receiver wires into the Wire
Manager trough.
10. Attach Power Strip (optional)
Using prepunched position holes, mount power strip mounting plates
to base using two (2) 10 - 16 x 1/2 sheetmetal screws. See power
strip assembly instruction P/N 939501344 for more information. Snap power
strip onto mounting plates as shown.
3"

Page 7 of 9
TS40005EM Rev C
11.Plug in Power Adaptor
Plug power adaptor into controller and power strip as shown.
12. Tighten all Screws
Check to see that all screws are tight. Using caution, gently lift the
mobile easel up onto its casters.
13. AttachTop Cover
Orienting the wire pass thru cutout as shown, snap the top cover over
the top plate and push down into place, keeping both ends level during
assembly. Receiver wires should route thru wire pass thru cutout.

Page 8 of 9
TS40005EM Rev C
14.Install StorageTray
Place the Storage Tray in the Center Shelf as shown. 15. Attach Printer Cable Attach printer cable and printer as shown. Using three (3) wire manager
routing aids, manage excess receiver and user interface cables as shown.
WIRE MANAGER
ROUTING AIDS

Page 9 of 9
TS40005EM Rev C
16. Scribble Away
Using the electronic pens and eraser you can now create and share
markerboard images. Remember to always use Expo dry erase
markers with your Turnstone Mobile Easel w/Mimio. Refer to owner's
manual to get the most out of your new Turnstone Mobile Easel
w/Mimio, or visit www.mimio.com.
Refer to the User's Guide for operating instructions, battery
replacement guide, and use of Mimio with your PC.
p
lkret 
sdfgn, ty 
sd oiudfg ui 
dfsgdgs oom gh