Turntide Ves-artex indc60odp User manual

E

N

G

L

I

S

H

Operating Instructions INDC60ODP

103424

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. Read carefully before attempting to assemble, install, operate or

maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could

result in personal injury and/or property damage! Retain instructions for future reference.

VES-Artex Industrial

Ceiling Fan

INDC60ODP

Description

The VES-Artex model INDC60ODP ceiling fan is a high efficiency, industrial ceiling

fan. It is designed to create air velocity and a cooling effect on high speed. The

lower speeds can be used for reduced velocity or heat de-stratification. The low

speed gently de-stratifies the air giving a constant room temperature. The

INDC60ODP is outdoor rated, ETL Certified in the United States and Canada and

comes with plug and controller.

Unpacking

1. After opening carton, look for concealed damage.

2. If concealed damage is found, immediately le claim with carrier.

General Safety Information

Disconnect power

supply before wiring

connections are made to prevent possible

electric shock or damage to equipment.

Read and follow

instructions carefully.

Failure to comply with instructions could

result in re, electric shock, injury to

persons and/or damage to equipment.

Follow all

maintenance

procedures enclosed.

Failure to properly

ground unit could

result in severe electrical shock or death.

1. All wiring should conform to the

National Electrical Code in the United

States and local regulations.

2. Make certain the entire installation

is grounded as a precaution against

possible electrical shock.

3. Do not exceed maximum amperage

rating of the ceiling fan as overload-

ing can result in damage to ceiling

fan and control.

4. When wiring an electrical appliance

or device follow all electrical and

safety codes, as well as the most

recent National Electrical Codes

(NEC) and the Occupational Safety

and Health Act (OSHA).

Assembly

1. Remove all ceiling fan parts from the

box.

2. Tools and supplies needed – Flat and

Phillips screwdriver – 9/16” and 3/8”

open wrench or adjustable wrench,

2-3 wire nuts.

3. Install a junction box to accept the

wiring of the fan. In many cases, a

qualied electrician will be required

to install the outlet box keeping with

local electrical codes or to meet the

National Electrical Codes (NEC).

4. For installation to open web steel

joist – use threaded J-hook as sup-

plied. For wood joist construction

– use J-hook with lag threads. For

attachment in concrete, drill concrete

anchors into the concretes as per

specication applicable to National

Electrical Code procedures.

Printed in China

Version 2

2020

VES-Artex002

2020

Specications

Model Size Volts Amps Watts RPM Down-Rod Down-Rod

60"120 0.8 95 250 24" Down Draft

Type

PUM-012-INDC60-01

E

N

G

L

I

S

H

Operating Instructions INDC60ODP

2

Installation

Safety Product Inspection of Fan Prior to

Installation (Figure #1 and #2)

To reduce the risk of re

or electric shock, do not

use this fan with any solid-state speed con-

trol device.

To reduce the risk of per-

sonal injury, do not bend

the blade brackets when installing the brack-

ets, balancing the blades or cleaning the

fan. Do not insert foreign objects in between

rotating fan blades.

1. Make certain set screw (4) is tight to

ascertain wobble free operation.

2. Make certain cotter pin (5) is in place

and secure.

3. Make certain lock-nut (7) is tight and set

screw (6) is in place and secure.

4. Slide lower canopy (8) down over

rubber gasket (21) to create a tight seal.

5. Make certain lower canopy set screws

(2) are tight on downrod (1).

6. Make certain cotter pin (13) is in place

and secure.

7. Make certain bolt, cotter pin and nut

(16) are tight.

Hanging of Fan (Figure #1 and #2)

1. Wind one nut (9) down to bottom of J

hook (12) towards the curve. Add a lock

washer and then at washer (3) on top

of the nut (9).

2. Tighten slip loop of safety cable (11)

around J hook shaft (12) and a

structural member of the building. Leave

1 inch of slack in the cable.

Make certain crimp on safety

loop is secure (See Figure

#4). Make certain safety cable is attached

properly to hook and structural member.

3. Drill a 1/2” pilot hole for J hook. Put J

hook (12) through pilot hole in joist. Add

at washer and then lock washer (20)

and nut (22). Do not tighten completely

until fan is put in place on J hook. A

lubricant should not be used on the

single mounting screw; and the pilot

hole should be drilled no larger than the

minor diameter of the mounting screw

threads, and at least 38 mm (1-1/2”) of

the threaded part of the mounting screw

should be secured into a structural

wood joist to provide secure mounting.

4. Loosen set screw (18) on top canopy

(19) on fan downrod (1) and lower the

canopy to make room to place rubber

grommet (14) onto

mounting hook.

5. Tighten top nut (22) on J hook to raise

fan into proper installation

position.

6. Must be plugged into an approved

duplex receptacle. (see Figure #5 for

control wiring diagram).

If the fan is installed

outdoor or in a harsh

environment a GFCI (Ground Fault Circuit

Interrupter) outlet should be used.

7. Raise top canopy (19) up the downrod

to cover hook. Leave 1/8” gap between

top canopy (19) and hanging surface

(so downrod does not move o󰀨 center

which could make fan wobble or vibrate

and transmit motor noise to ceiling

surface). Tighten set screw (18).

8. Attach blades (23) to motor (24) with

blade bolts (25). (Figure #3) The blade

(24) should be positioned below the

blade arm bracket (26) when attaching

to the motor to get proper air ow and

direction.

VES-Artex Industrial Ceiling Fan

Figure #2

1

18

19

14

16

11

12

20 22

9

13 10

15

3

Figure #1

8

1

5

4

2

6

7

17 11

Safety

Cable

25

24

23 26

Figure #3

Figure #4

21

E

N

G

L

I

S

H

Operating Instructions INDC60ODP

3

IMPORTANT: VES-Artex

fan model INDC60ODP; for

wiring optional included

controller please see

instructions included with the

controller.

Control Installation:

The wall control switch has

been investigated and found

acceptable for use as a speed

control switch.

Models INDC60ODP

Length of downrod is

measured as shown above.

Top of Rubber

Grommet

Flat surface

blades attach.

24”

_______________________________________________________________________________________________________

E

N

G

L

I

S

H

Operating Instructions INDC60ODP

4

Maintenance Estimated Approved S - Scheduled Work Performed/

Date Running Hours Inspector Name: U - Unscheduled Notes/Comments

______________________________________________________________________________________

Maintenance

Always disconnect the

power supply before

servicing the ceiling fan or working with the

unit for any reason.

Parts replacement and

troubleshooting to be

performed only by qualied personnel.

Do not place ngers or

objects in the ceiling

fan while motor is connected to the power

source.

Do not attach foreign

objects to the blades of

the ceiling fan.

Do not use gasoline,

benzene, thinner, harsh

cleaners, etc., which are dangerous and will

damage the ceiling fan.

If you see noticeable

vibration, wobbling or

wear the fan should be removed from service

and repaired or replaced by a qualied

maintenance technician or electrician.

• Below is the maintenance schedule

that must be followed and lled out to

be eligible for warranty and ensure safe

operation.

• Inspection should be every 3500

running hours or every 6 months.

• Maintenance schedule should include

repeating the product inspection

procedure and the fan hanging

procedure.

Initial Installation Date : ______________________ Name of installation supervisor : ______________________________

Maintenance Schedule

E

N

G

L

I

S

H

Operating Instructions INDC60ODP

6

Troubleshooting Chart

VES-Artex Industrial Ceiling Fan is tested before it leaves the factory, resulting in an

extremely low rate of returns. However, due to shipping and installation procedures, oc-

casionally a fan will need a minor adjustment to run satisfactorily. If this should

happen, we recommend that you identify the problem and try the simple suggestions

listed below.

Turn o power at main circuit breaker before checking!

Fan will not start a) Check fuses and circuit breakers.

b) Check wire connections to fan.

c) Check wiring connection in lower canopy.

d) Check voltage at fan connection.

_______________________________________________________________________________________________________

___________

Fan too fast / slow a) Adjust the trim set screw in fan wall control if using optional wall control. If minimum setting

is too low the fan may shut o󰀨 with voltage uctuations. Increase minimum.

b) Check voltage at fan connection.

c) Blades must be attached to motor to reduce the speed.

_______________________________________________________________________________________________________

___________

Fan makes noise a) Check motor case to make certain all visible screws are snug.

b) Check to make certain that all blade bracket screws are tight.

c) Check for labels or wire nuts that could be rubbing.

d) All ceiling fans may have a slight motor noise known as the “60 cycle hum” when used with

solid state innite speed controls. Especially on lower speeds. This hum will not a󰀨ect the

fan performance.

e) Make certain upper canopy is at least 1/8” from ceiling

f) Allow a 30 days break-in period which normally eliminates any Residual noise other than a),

b), c), d) or e).

_______________________________________________________________________________________________________

___________

Fan wobbles a) Check that all blade brackets are screwed rmly to motor case.

b) Check distance from tip of blades to ceiling. If blades get bent during installation, you must

re-adjust them so that all blades travel on same plane. Gently bend up or down until all

distance are the same.

c) Make certain upper canopy is 1/8” from ceiling.

d) Make certain that hanging hooks are secured tightly to ceiling.

e) Run fan without blade, if motor does not wobble, then motor is not defective but the blades

maybe bent.

Symptom Corrective Action

E

N

G

L

I

S

H

Operating Instructions INDC60ODP

7

LIMITED WARRANTY

VES-ARTEX ONE-YEAR LIMITED WARRANTY ON ALL PARTS ONLY WITH ACCOMPANYING MAINTENANCE

SCHEDULE. VES-ARTEX MODELS COVERED IN THIS MANUAL, ARE WARRANTED BY VES-ARTEX (VES-ARTEX) TO THE

ORIGINAL USER, AGAINST DEFECTS IN WORKMANSHIP OR MATERIALS UNDER NORMAL USE FOR ONE YEAR ON ALL

PARTS AFTER DATE OF PURCHASE . ANY PART WHICH IS DETERMINED TO BE DEFECTIVE IN MATERIAL OR WORK-

MANSHIP AND RETURNED TO AN AUTHORIZED SERVICE LOCATION, AS VES-ARTEX DESIGNATES, SHIPPING COSTS

PREPAID, WILL BE, AS THE EXCLUSIVE REMEDY, REPAIRED OR REPLACED AT VES-ARTEX’S OPTION. FOR LIMITED

WARRANTY CLAIM PROCEDURES, SEE “PROMPT DISPOSITION” BELOW. THIS LIMITED WARRANTY GIVES

PURCHASERS SPECIFIC LEGAL RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.

LIMITATION OF LIABILITY. TO THE EXTENT ALLOWABLE UNDER APPLICABLE LAW, VES’S LIABILITY FOR

CONSEQUENTIAL AND INCIDENTAL DAMAGES IS EXPRESSLYDISCLAIMED. VES-ARTEX’S LIABILITY IN ALL EVENTS IS

LIMITED TO AND SHALL NOT EXCEED THE PURCHASE PRICE PAID.

WARRANTY DISCLAIMER. ADILIGENT EFFORT HAS BEEN MADE TO PROVIDE PRODUCT INFORMATION AND

ILLUSTRATE THE PRODUCTS IN THIS LITERATURE ACCURATELY; HOWEVER, SUCH INFORMATION AND

ILLUSTRATIONS ARE FOR THE SOLE PURPOSE OF IDENTIFICATION, AND DO NOT EXPRESS OR IMPLYAWARRANTY

THAT THE PRODUCTS ARE MERCHANTABLE, OR FIT FOR APARTICULAR PURPOSE, OR THAT THE PRODUCTS WILL

NECESSARILYCONFORM TO THE ILLUSTRATIONS OR DESCRIPTIONS. EXCEPT AS PROVIDED BELOW, NO WARRANTY

OR AFFIRMATION OF FACT, EXPRESSED OR IMPLIED, OTHER THAN AS STATED IN THE “LIMITED WARRANTY” ABOVE

IS MADE OR AUTHORIZED BY VES-ARTEX.

Technical Advice and Recommendations, Disclaimer. Notwithstanding any past practice or dealings or trade custom,

sales shall not include the furnishing of technical advice or assistance or system design. VES-Artex assumes no obligations or

liability on account of any unauthorized recommendations, opinions or advice as to the choice, installation or use of

products.

Product Suitability. Many jurisdictions have codes and regulations governing sales, construction, installation, and/or use of

products for certain purposes, which may vary from those in neighboring areas. While attempts are made to ascertain that

VES-Artex products comply with such codes, VES-Artex cannot guarantee compliance, and cannot be responsible for how the

product is installed or used. Before purchase and use of a product, review the product applications, and all applicable national

and local codes and regulations, and be certain that the product, installation, and use will comply with them.

Certain aspects of disclaimers are not applicable to consumer products; e.g., (a) some jurisdictions do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you; (b) also,

some jurisdictions do not allow a limitation on how long an implied warranty lasts, consequently the above limitation may not apply

to you; and (c) by law, during the period of this Limited Warranty, any implied warranties of implied merchantability or tness for a

particular purpose applicable to consumer products purchased by consumers, may not be excluded or otherwise disclaimed.

Prompt Disposition. A good faith eort will be made for prompt correction or other adjustment with respect to any

product which proves to be defective within limited warranty. For any product believed to be defective within limited

warranty, first write or call dealer from whom the product was purchased. Dealer will give additional directions. If unable to resolve

satisfactorily, write to VES-Artex at address below, giving dealer’s name, address, date, and number of dealer’s

invoice, and describing the nature of the defect. Title and risk of loss pass to buyer on delivery to common carrier.

If product was damaged in transit to you, file claim with carrier.

Manufactured for VES-Artex, Chippewa Falls, WI 54729 USA

E

N

G

L

I

S

H

Operating Instructions INDC60ODP

8

Notes

________________________________________________________________________________________

TURNTIDE VES-Artex INDC60ODP User manual

Popular Fan manuals by other brands