TV One C2-6104A User manual

QSG- C2-6104A-V1.00
May 2019
C2-6104A Video Processor
Quick Start Guide V1.00

 

 

In this guide
About your C2-6104A................................................................................ 1
Quick start .................................................................................................. 5
The menu.................................................................................................... 6
Regulatory compliance ........................................................................... 13
Contact us................................................................................................. 14
Thanks for buying this C2-6104A from tvONE™.
The C2-6104A features four video processing and scaling engines,
with video mixing, keying, fading, and source-labeling capabilities.

QSG- C2-6104A-V1.00 1
About your C2-6104A
The front panel

SELECT
Use  to navigate in the menu.
Press SELECT to select options.
Press and hold SELECT to save your
current settings.
Preset buttons.
Press a preset button to load a preset
window layout.
You can overwrite the presets
associated with these buttons. To
overwrite a preset with your current
settings, press and hold a preset
button until you hear a beep.
Hold to Store 1-5
Custom preset buttons.
Press a preset button to load a preset.
To store your current settings as a
preset, press and hold a button from
1-5 until you hear a beep.
Hold for ID A, B, C, D
Press a button from A-D to select a
window to adjust. This window is the
active window.
DVI-1, DVI-2, DVI-3, DVI-4
Press a button from DVI-1 to DVI-4 to
select a source for the active window.

2 tvONE
KEY
Press to enable keying for the active
window.
The default key color is black, the
black foreground becomes
transparent.
ZOOM
Press to open Adjust windows > Zoom
level.
FREEZE
Press to freeze and unfreeze the active
window.
CYCLE
Press to cycle your sources through
the windows.
POS
Press to open Adjust windows > H/V
position %.
Use H/V position % to pan or position
the image.
PIP
Press to activate picture-in-picture
mode. The active window becomes the
picture-in-picture. The next window
becomes the main window. For
example, if window A is the active
window, window B becomes the main
image, with window A as the picture-
in-picture.
If you don’t select an active window,
the main image is a still image from
the still image store, with window A as
the picture-in-picture.
SIZE
Press to open Adjust windows > Shrink
level %.
Use Shrink level % to resize the
window.

QSG- C2-6104A-V1.00 3
ON
STANDBY
Press and hold to enter standby
mode.
Press to enter active mode.
Button combinations
These button combinations only work when the unit is in active
mode.
Locking the front panel buttons
To lock and unlock the front panel buttons, press and hold ON
STANDBY and FREEZE together.
Saving current settings
To store your current settings so that they appear next time you
power on your unit, press and hold SELECT until you hear a beep.
Restoring factory settings
To restore your unit to its factory settings, press and hold
ON STANDBY and SELECT together, until you hear two beeps.
Note: When you restore factory settings, all stored settings except
resolutions are deleted. To delete resolutions as well, update your
firmware.
Shortcuts to specific resolutions
Press these buttons together to set the following resolutions:
Buttons
Output resolution
1 and A
720x480p @59.94 Hz
2 and A
1280x720p @59.94 Hz
3 and A
The default resolution
1280x720p @60 Hz

4 tvONE
The rear panel
This unit has 4x DVI-U inputs, 1x DVI-U background input and 1x
DVI-I output.
RS232
Connect to your serial
controller
1.2A Max
Connect to a power outlet
IP
Connect to Ethernet to control
your unit remotely
INPUTS
DVI-I 1, DVI-I 2, DVI-I 3, DVI-I 4
Connect to your sources
You can connect a range of
sources with our adapters.
Read more at tvONE.com.
BACKGROUND/CASCADE
Connect to a source.
The source can be another C2-
6XXX unit. This input can only
be displayed as the background
image, window Z.
OUTPUT
Connect to your display

QSG- C2-6104A-V1.00 5
Quick start
Set up and test your unit with factory default settings.
1. Connect one or more DVI-D or analog sources to the input
ports.
You can connect analog sources with a VGA to DVI-A
adapter.
2. Connect a display to the output port.
The default output resolution is 1280x720p @60 Hz. For best
results, make sure your display supports this.
3. Power on your C2-6104A.
4. Press the first preset button.
Your sources show on your display.
5. If you have any problems, restore your unit to factory
settings and then try setting up again.
Press and hold ON STANDBY and SELECT until you hear a
beep.
For troubleshooting advice, see the user guide. There’s a link
on the back page of this quick start guide.

6 tvONE
The menu
Use the menu to make changes to your system.
For more information about menu options, see the user guide.
Map of the menu
Adjust
Preset
Load, Store,
Erase
Adjust
Outputs
Lock mode
Output res
HDCP
Output Type
The default output signal is RGBHV
Stand
This option is only available when
you set the output resolution to PAL
or NTSC
Back Y/U/V
Allow HDMI
output
SC/H Phase
This option is only available when
you set the output resolution to PAL
or NTSC
Allow HDMI
output
Allow Errors
Audio emb
Exit
Adjust
windows
Window to adjust
Source

QSG- C2-6104A-V1.00 7
Window enable
Zoom level %
H/V zoom pan %
Image freeze
H/V crop %
H/V out shift
Shrink level%
H/V position %
Aspect change
Aspect adjust
For detailed information about
using this setting in advanced or
pixel mode, see the user guide.
Details are at the back of this quick
start guide.
Image smoothing
Image flip
Show source
label
Max fade level %
Layer priority
ABCDZ
Exit
Adjust
keyers
Window to adjust
Keyer enable
Y Key min/max
Y Key soft

8 tvONE
U Key min/max
U Key soft
V Key min/max
V Key soft
Exit
Adjust
borders
To adjust a border, select a window
to adjust in the Adjust Windows
menu.
Border enable
Brdr offset H/V
Brdr Y/U/V
Brdr opacity %
Exit
Adjust
sources
Source to adj
UMD display
address
This option is only available when a
tally module is installed.
Lbl HVpos
This option is only available when
you select a source from 1 to 4
Label Char
(character)
This option is only available when
you select a source from 1 to 4
Lbl for/bck col
This option is only available when
you select a source from 1 to 4
Lbl font / H / V
size
This option is only available when
you select a source from 1 to 4
HDCP
This option is only available when
you select a source from 1 to 5
Display Emul
This option is only available when
you select a source from 1 to 5