TV One Magenta Encoder-100 User manual

Firmware version1.05.03.007and above
QSG-ENCODER-100-V1.00
May 2017
Encoder-100 Streaming Media Encoder
Quick Start Guide V1.00

In this guide
About your Encoder-100 2
Quick start 3
Regulatory compliance 9
Contact us 9

QSG-ENCODER-100 1
Thanks for buying this Encoder-100 from tvONE.
The Encoder-100 streaming media encoder allows you to stream high
quality video and audio from a range of sources to the Streaming
media and 4K playback input module of your CORIOmaster™,
CORIOmaster mini™, or CORIOmaster micro™.
Features
nConvert video and audio to high quality digital stream.
nHigh quality, low bandwidth encoding with H.264 compression.
nFull 1080p HD support at up to 60frames per second.
nSupports unicast and multicast streaming.
nHDMI video and audio input and output.
nAnalog audio input and output.
nPreview your video signal and stream separately.
Recommendations
nFor best results, use Gb Ethernet cables and equipment.
nIn industrial environments, use shielded Ethernet cables.
Shielded Ethernet cables are often marked F/UTP or FTP.

2 MagentabytvONE
About your Encoder-100
Encoder-100 rear panel
DC5V Connect to an electrical outlet
LAN Sends encoded signal to your network
Connect to your network with Ethernet
PREVIEW Allows you to preview your encoded signal
Connect to a display with a VGA cable
HDMIOUT Allows you to preview your encoded signal
Connect to a display with an HDMI cable
HDMIIN Receives video and digital audio signal from a source
Connect to a source with an HDMI cable
AUDIOOUT Allows you to preview your audio signal
Connect a speaker with a 3.5mm jack audio cable
AUDIOIN Receives analog audio from a source
Connect a 3.5mm jack audio cable
Note: audio is supported by CORIOmaster micro™
only

QSG-ENCODER-100 3
Quick start
It's easy to get started with the Encoder-100, but if you want more help with any
of these steps, select in CORIOgrapher™ and search, or ask a question.
The Encoder-100 cannot encode HDCP encoded sources.
Before you start
To use an Encoder-100, you must have a Streaming media and 4K
playback input module installed in your CORIOmaster™, CORIOmaster
mini™, or CORIOmaster micro™.
Setting up the Encoder-100
Connect your cables.
A. Connect the power supply to an electrical outlet.
B. Connect an Ethernet cable to your network.
C. Connect an HDMI cable to the video source that you wish to
stream.
For example, you could connect a camera, an endoscope, or a
media player.

4 MagentabytvONE
nOPTIONAL: if you want to stream analog audio, or preview your
audio, connect a 3.5mm jack audio cable.
nOPTIONAL: if you want to see a preview of your stream, connect a
VGA cable to PREVIEW, or an HDMI cable to HDMIOUT, and to a
display.
The power connector is a
latching power connector. To
remove the power connector
from your Encoder-100, slide
the sleeve backward.
Configuring the Encoder-100 with CORIOgrapher™
1. Open CORIOgrapher™ , connect to your CORIOmaster™, and read
the configuration from your device.

QSG-ENCODER-100 5
2. Set up a video wall that includes at least one window playing the
Streaming media and 4K playback input module, and select Take.
3. Double-click the window you wish to play streaming media, and
select (Media Player) Manage.
4. Select IP Streams, select your Encoder-100, and select Manage.

6 MagentabytvONE
When you first connect, your Encoder-100 is named with its ID
number. Find the ID number is on the bottom of your Encoder-100.
If your Encoder-100 isn't displayed, select Find and enter the URL
of your Encoder-100.
5. Select System, and name your Encoder-100.
Names can be up to 62 characters long, and can't be blank.
6. Select Network, and choose network settings for your Encoder-
100.

QSG-ENCODER-100 7
nIf you choose DHCP, an IP address is assigned to you.
nIf you choose a static IP address, enter a value for your IP
address, subnet mask, and gateway.
If you need help with network settings, contact your network
administrator.
Static IP address
If you choose a static IP address, make sure you enter a unique value for
your IP address. Using the same IP address for multiple devices can cause
your devices to disconnect. Contact your network administrator for help.
7. Select Capture, and check that your audio source is correct.

8 MagentabytvONE
8. Select Encode, and choose a profile.
The profile you choose depends on the bandwidth of your
connection and your quality requirements. The default settings
produce a high quality stream.
9. Select Status >Start encoding.
Read more about configuring encoders in CORIOgrapher™ Help.