TVILIGHT CitySense Plus User manual

CitySense Plus
Installation Manual
Cable Gland
English

Page 2 of 10
Version Author Date Changes Approved by
v4 Henri Eskonen 21/12/2017 Added version
control page. Minor
formatting.
v4 - 21/12/2017
TVILIGHT BV / Westerhaven 13, 9718 AW Groningen, the Netherlands
[phone] / [email protected] / www.tvilight.com

Page 3 of 10
In order to function properly, CitySense Plus must be
connected to a dimmable driver/ballast.
NOTE: Some dimmable drivers/ballasts must be
programmed/set to dimmable mode. If this has not been
done, CitySense Plus will not be able to dim the connected
armature.
ATTENTION:

Page 4 of 10
In box:
5m Cable
M16 Cable Gland Sticker
Generic Strap x 2
You’ll need:
Max = 11mm
Min = 8mm
M16 ThreadDrill
Wago x 4
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014

Page 5 of 10
1. Push cable gland through wire
2. Drill M16 threaded hole into pole
5m
Note: for added protection against rust, the use of an anti-corrosion
spray such as WD40 Corrosion inhibitor or equal is recommended.

Page 6 of 10
3. Run wire through hole
4. Screw cable gland in hole
Rotate the cable gland to tighten
Twist the end leads
of the wires

Page 7 of 10
5. Strap product to pole
6. Level the product
* Ensure Tensioning Tool is set
to maximum tension (#4)
Tensioning Tool
Position 2: Standard
1
2
3

Page 8 of 10
SAME
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
TVILIGHT
www.tvilight.com
TVI-CSP1-01-0014
7. Apply product ID sticker to pole
2 m

Page 9 of 10
Wiring Diagram
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.
DC +
Connector
(e.g. Wago)
AC in(N)
AC in(L)
DC -
L
N
Junction Box
GND
GND NL L out N out
DC-DC+
GREEN BROWN WHITE
BLACK GREY
BLUE RED

Page 10 of 10
ARMATURE
JUNCTION BOX
GND
GND
1-10V+
or
DALI+ N
N
L
L
L
GND
N
L
CITYSENSE +
Lout Lin Nin
N
DC-
DC+
1-10V-
or
DALI-
1-10V-
or
DALI-
1-10V+
or
DALI+
GND
GREEN BROWN WHITE BLACK GREYBLUE RED
NLLout Nout
1-10V-
or
DALI-
1-10V+
or
DALI+
Wiring Diagram
WARNING:
If not correctly connected product might not
function or it might be permanently damaged.
Note: For added protection, it is recommenteded to add an external
circuit breaker at the power input of the product. Circuit breakers such
as the ELeQ LS-94 5L2408 or similar rated products could be used.

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 4 meters
Tilt: 0 degrees
2 m
7.5 m
2 m
0.5 m
7 m
3.2 m
13.5 m
4.5 m

2.7 m
10.65 m
2.42m
4.16 m
2.25 m
3.7 m
1.1 m
2.2 m
9.4 m
14.8 m
14 m
5.3 m
4.9 m
CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 4 meters
Tilt: 7.5 degrees

12.8 m
12.8 m
5.2 m
4.1 m
5.6 m
2.1m
5.2 m
1 m
2.42m
4.16 m
2.25 m
CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 4 meters
Tilt: -7.5 degrees

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 4.5 meters
Tilt: 0 degrees
8.5 m
2.25 m
3.6 m
2 m
0.6 m
15 m
5 m
7.7 m

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 4.5 meters
Tilt: 7.5 degrees
12.1 m
3 m
4.7 m
2.7 m
2.25 m
4.1 m
1.2 m
2.5 m
10.5 m
16.7 m
15.8 m
6 m
5.5 m

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 4.5 meters
Tilt: -7.5 degrees
4.6 m
6.3 m
2.4 m
1.1 m
6 m
5.8 m
10.5 m
14.3 m
2.7 m
4.7 m
2.25 m

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 5 meters
Tilt: 0 degrees
2.5 m
9.5 m
2.5 m
4 m
16.5 m
5.5 m
0.7 m
8.5 m

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 5 meters
Tilt: 7.5 degrees
5.2 m
3 m
13.5 m
3.4 m
2.75 m
18.5 m
17.5 m
6.6 m
6.1 m
4.6 m
1.4 m
2.8 m
11.7 m

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 5 meters
Tilt: -7.5 degrees
7 m
2.6 m
1.3 m
6.5 m
15.9 m
11.8 m
6.4 m
5.1 m
5.2 m
3 m
2.45 m

CitySense Plus - Indicative Sensor Detection Zones
Mounting Height: 5.5 meters
Tilt: 0 degrees
10.5 m
2.75 m
2.75 m
4.4 m
16.5 m
5.5 m
0.7 m
9.3 m