twotrees SP-5 User manual

LETTER FROM TWOTREES 致客户的一封信
Dear Customers，
Thank you for choosing us.
It’s customer-oriented idea, continuous innovation and pursuit of excellence that enable
everybody to have wonderful experience in using process.
We believe that this manual will be helpful.
Hope you enjoy the good time with TwoTrees.
If you have any problems, please feel free to contact us via
Website: www.twotrees3d.com
Facebook: https://www.facebook.com/groups/twotrees3Dprinter/
For general inquiry: [e-mail]
For technical support: [e-mail]
We will contact you within 24 hours.
Sincerely yours,
TwoTrees Team
亲 爱 的 客 户：
感谢您选择了我们品牌。
我们一直以客户为导向，不断创新，追求卓越，使每个人都能在使用过程中拥有丰富的体验。
希望您能享受与俩棵树相伴的好时光。
如果您有任何问题，请随时与我们各购买平台的客服联系。
其他联系渠道有：
网站：www.twotrees3d.com
售后邮箱：[e-mail]
咨询邮箱：[e-mail]
我们将在24小时内联系上您。
祝您生活愉快！
俩棵树团队

For a better experience in using our product, please read this page carefully.
为了更好地使用我们的产品，请仔细阅读本页。
1. Please ensure that the packaging is complete before confirming receipt.
确认收货前请确保包装完整；
2. After unpacking, please check the parts list and accessories carefully.
开箱后请仔细核对零件清单及附件；
3. If any problems, please feel free to contact us.
如有任何问题，请随时与我们联系。
PRECAUTIONS 注意事项
When the machine is operating, do not place the printer near any heat source or flammable or
explosive objects. We suggest placing it in a well-ventilated, low-dust environment.
机器运行时，不要将打印机放在任何热源或易燃易爆物体附近。我们建议将其放置在通风良好、低尘的环境中。
Adult supervision: Ensure machine is not accessible to young children.
成人监督：确保幼儿无法接触到机器。
Hot Surface Hazard: Do not touch the nozzle or printing surface during operation as they may be
hot. Keep hands away from machine while in use. Hot surface may cause burns or personal injury.
烫伤危险：操作过程中请不要触摸喷嘴或打印表面。使用时，手应远离机器，以防烫伤或其他伤害。
The printer with 220VAC / 110VAC and other high-voltage power interfaces. Do not use any other
power cable except the one supplied. Please operate with care.
打印机具有 220VAC / 110VAC 和其他高压电源接口。除所提供的电源线外，请不要使用任何其他电源线。
Ensure that the terminals are firmly connected to avoid sparks due to loose wiring. Do not leave
the machine unattended when in operation.
确保终端牢固连接，以避免因线路松动而产生火花。运行时，请尽量不要让机器处于无人看管的状态。
When cleaning debris from the printer hot end, always use the provided tools. Do not touch the
nozzle directly when heated; cause personal injury.
在清理打印机热端的碎屑时，请使用所提供的工具。加热时不要直接触摸喷嘴，以防造成不必要的伤害。
The printer is a kind of mechanical equipment. Please keep away from moving parts during machine
operating so that free from potential safety problem.
机器运行时，请远离运行中的部件，以避免安全隐患。
Please regularly lubricate and maintain the guide rails.
请定期润滑并保养导轨。
Make sure that parts of your body are in contact with the ground before touching the machine to
avoid damage of electronic component caused by static electricity.
在接触机器之前，请确保身体部位是与地面有所接触的，以避免静电造成的电子部件损坏。
SAFETY GUIDELINES 安全指导

A b o u t Yo u r P r i n t e r 关 于 机 器 ------------------------------------------
P a r t L i s t 配 件 表 --------------------------------------------------
M a c h i n e P a r a m e t e r s 机 器 参 数 ------------------------------------------
A s s e m b l y P r o c e s s 安 装 ---------------------------------------------
Test & Adjust 检测与调整 -------------------------------------------
E r r o r S y m b o l s & D e f i n i t i o n 错 误 标 志 与 定 义 ----------------------------------
A f t e r- S a l e s S e r v i c e 售 后 服 务 ------------------------------------------
CONTENTS
01
02
03
04
21
23
24

1. T8 Lead Screw Holder
丝杆固定座
2. Double Extrusion wheel
双驱动挤出机
3. Filament Holder
耗材支架
4. Cable Access Cover
走线槽盖板
5. Beam Carriage
横梁马车
6. Extrusion Head Kit
挤出头套件
7. Front Cover
主盖板
8. USB Port
USB 端口
9. TF Card Slot
TF卡插槽
10. Y Axis End stop
Y轴限位开关
11. Heating Plate
热床
12. Leveling Screw Nuts
底座调平螺母
13. Z Axis Linear Rail
Z轴导轨
14. T8 Lead Screw
T8丝杆
15. Coupling
联轴器
16. 3.5” Full Color Touch Screen
3.5英寸全彩触摸屏
17. Heating Plate Support
热床支架
18. Chassis Cooling Fan
机箱散热风扇
19. Power Switch
电源开关
ABOUT YOUR PRINTER
SP-51TWOTREES

PART LIST
配件表
Foot Pad 脚垫 x 4
M4*12 Screw 螺丝 x 4
M5*10 X 12 M5*16 X 8
2040 Profile 2040型材 X 4
2020 Profile 2020型材 X 2
Z-axis Linear Rail Z轴安装 X 2
M5*30 Screw 螺丝 X 4 Machine Roof 机顶 X 1
M5*16 Screw 螺丝 X 8
M5*10 Screw 螺丝 X 8
Triangle Aluminum 三角铝件 x 4
T-nut T型螺母 x 8
M4*8 Screw 螺丝 x 8
Heating Plate Support 热床支架 × 2
M3*6 Screw 螺丝 X 8
T8 Lead Screw X 2
T8 丝杆
T8 Lead Screw Holder 丝杆固定座 x 2
T-nut T型螺母 x 4
M4*8 Screw 螺丝 x4
Leveling Screw Nut 调平螺母 x 4
Spring 弹簧 x 4
Countersunk Head Screw 沉头螺丝 x4
Heating plate 热床 x 1
Extrusion Head Kit × 1
挤出头套件
Extruder 挤出机 x 1
M4*8 Screw 螺丝 x 2
T- n u t T 型螺母 x 2
M4*8 Screw 螺丝 × 1
Wire Clip 线夹 × 1
Teflon Tube 四氟管 × 1
Filament Holder 耗材支架 x 1
T-nut T型螺母 x 2
M4*8 Screw 螺丝 x 2
Profile Cover Strip X 3
型材封条
Filament Sensor X 1
断料检测器
Chassis Plate X 1
机器底部
Heating Plate Glass X 1
晶格玻璃
USB Cable X 1
USB 数据线
AC Power Cable X 1
AC 电源线
(For local specifications)
Filament 耗材 X 1
(Random Color)
(颜色随机)
Tools Package X 1 工具包
(With TF 包含TF卡)
Insulating Sponge
隔热棉 x 1
5
SP-5 2TWOTREES

MACHINE PARAMETERS
机器参数
Model 型号： SP-5 蓝宝石 PLUS
Colour 颜色： Black黑色
Material 材质： Sheet Metal钣金
Number of nozzles 喷嘴数量： 1
Nozzle diameter 喷嘴直径： 0.4mm
Heating plate 热床： 310*310mm
Printing size 打印尺寸： L300*W300*H350mm
Printing accuracy 打印精度： ±0.1mm
Layer thickness 层厚： 0.1-0.4mm
Printing method 打印方式： TF Card / Online Printing(PC)
Display 显示屏： 3.5” Color touch screen 3.5英寸彩色触摸屏
Recommended speed 推荐速度： 60mm/s
Printing speed (MAX) 打印速度（最快）: 200mm/s
Nozzle Temperature (MAX) 喷嘴温度（最高）： 260° C (500°F)
Heating plate Temperature (MAX) 热床温度（最高）： 100°C (212°F)
XY axis positioning accuracy 轴定位精度： ±0.01mm
Z axis positioning accuracy 轴定位精度： ±0.01mm Print
material打印材料： PLA, ABS, PETG Wooden Filament 木制耗材
Filament diameter 耗材直径： 1.75mm
Language 操作语言： EN, RU, ES, FR, DEKR, ZH-CN
File format 文件格式： STL, OBJ, JPG
Print file format 打印文件格式： G-code
Machine size 机器尺寸： L485*W460*H590mm
Package size 包装尺寸： L630*W540*H250mm
Machine weight 机器重量： 18kg
Package weight 包装重量： 20kg
电源参数 Electrical requirement： 220V/110V 360W
PC requirement 操作系统： Windows, MAC Support
software 支持软件： Cura, 3DPrinterOS, Repetier-Hostand others
Operating environment 工作环境： Temperature温度: 5-40°C;
Humidity湿度: 20-60% RH
SP-53TWOTREES

1.Install the Standing Feet 安装脚垫
Turn Over 反转过来
Foot Pad 脚垫
x4
M4*12 Screw 螺丝
x4
SP-5 4TWOTREES

2. Install The Frames 安装框架
2040 Profile 型材
x4
2020 Profile 型材
x2
Z-axis Linear Rail
Z轴导轨
x2
M5*10 Screw 螺丝
x12
M5*16 Screw 螺丝
x8
Note: The guide rails face inwards.
The upper slots of the four main frames are always on the edge.
The cover sides of the beams face out.
注意： 导轨是朝内的; 四个主要框架的上部插槽始终处于机器边缘； 横梁的封面朝外。
①
①
②
② ②
②
①
①
SP-55TWOTREES