tws Macaron AirPods i12 User manual

The TWS i12 Ear-pods
User Guide
Taken from the website www.thephonetalks.com
How to turn on or off the i12 TWS?
•Turn on: The two i12 TWS Earpods will automatically turn on and pair after
removing them from the charging case.
•Turn off: Press and hold the back of the sensor for 10 to 20 seconds. You will hear
a beep indicating that the earphone has turned off.

How to pair the i12 TWS to any product?
The two i12 TWS Earpods will automatically turn on and pair with any smart device if it has
Bluetooth On. To know if the connection was made, the left earphones will flash blue and the
red LED of the right earphones will turn off when paired successfully, in addition the
“connected” message will be heard after pairing.
Note: If two earphones have not been paired with each other, please delete the paired
information from the earphones, then long-press the power button of both earphones for 5 to
10 seconds to enter pairing mode; the left earbuds will blink blue and the red LED on the

right earbuds will turn off when paired successfully. It is worth noting that the headphones will
turn off if they can’t sync within 5 minutes.
In case the paired information needs to be deleted, it is done as follows: In pairing mode,
press the back of the earphone on the sensor until the LED light turns red.
How to play music with the i12 TWS?
Note: There are different i12 TWS Earpods available on the market. Since it is not a
registered name, it is used by different Chinese manufacturers. As a result, buyers have
different touch control functions. Here are some models with different touch control
functions:
Model 1

•A single tap on either: pause/play
•Double-tap on right: back
•Double-tap on left: forward
•Triple tap on right: volume up
•Triple tap on left: volume down
•Call Siri: Press and hold the power button for 3 seconds during playback mode.
Model 2
•A single tap on either: pause/play
•Single tap without music player open: calls the last contacted person.
•Double-tap on right: volume up
•Double-tap on left: volume down
•Triple tap on right: rewind/previous
•Triple tap on left: next
•Call Siri: Press and hold the power button for 3 seconds during playback mode.
How to answer phone calls with i12 TWS
earphones?
•Answer/end call: Press the back of the earphone once.
•Reject call: Double press the back of the earphone.

How to charge i12 TWS?
i12 TWS Headphone charging
Put the headphones in the slot of the charging case, and then turn on the charging case.
The LED indicator will flash red and turn off after a full charge.
Charging the battery box (charging case)
When charging the battery box with a USB cable, the LED indicator will
light yellow and green. If the LED blinks 2 times it means your battery is 50% full, if itblinks 3
times it means it is 75% charged and if it blinks 4 times it means it is 100% full.
Troubleshooting
Q.1 How to fix/change the call option due to accidental
tapping on the left earphone?
Go to your Bluetooth settings and turn off the phone control option. So it only has access to
media. Go to your Bluetooth settings and turn off the phone control option. However, you
will have to sacrifice the complete tap control.
Q. What if only one earphone is working and the other one
is not connecting?
The best way to check if both earphones don’t have any hardware fault is that when both
earphones are connected to the charging box they will have the Red LED light. If there’s
only one light blinking this means that only one earphone is connected. Here are some
solutions to connect the other one as well:
Solution no.1: Put them back in the case. Take them out at the same time and wait for
them to be paired. Wait for at least 20 to 30 seconds.
Solution no.2: Try pressing the earphone which is not working for 3-5 sec. If nothing
happens, try holding the sensor for about 30 secs.
Solution no.3: It may be that one of your earphones which is not working might be low on
battery. If you have already tried to charge it up and didn’t succeed. Try moving them

around the box while the box light is blue, when they catch connection with the box, they will
light up red. Use a paper towel or a tissue, do some folds and attach it inside the box top lid.
Place the earphones and close the lid. Just try moving them around the box while the box
light is running blue when they catch connection with the box, they will light up red. If one
side isn’t charging, this will push the earphone of that side to attach with the charging
terminal and charge.
If you succeeded with solution no.3, it looks like we have the charging box defect here.
If none of the solutions worked, your earpiece is faulty, go for replacing it.