Tycon Power Systems TP-MS4x4 User manual

TP-MS4x4
4 Port Gigabit PoE Injector
USER’S MANUAL
TYCON POWER SYSTEMS

User’s Manual TP-MS4x4 V5
TYCON POWER SYSTEMS
2
1. General Information
The TP-MS4x4 is a DC/DC PoE (Power over Ethernet) Injector, provide up to 4 different voltage
DC input and four different voltage PoE output, output power maximum 1A/port, data rate can be
10M/100M/1000M. The polarity of each PoE output can be reversed if you need to reverse the
output polarity. This manual will help you to install and setting the PoE injector.
2. Hardware Description
Front panel detail
the port number is as the diagram shows.
Rear panel detail
4 3 2 1 Data in
4 3 2 1 Data + Power out

User’s Manual TP-MS4x4 V5
TYCON POWER SYSTEMS
3
*LED Indicator
There are 4 LEDs on the front panel to indicate the input and output power status of each port.
LED STATUS Description
1~4 Green A valid power device is detected on this port.
Active current is 80mA.
Red No power device is detected on this port.
Off No input power apply, or input source alarm.
Alarm voltage is less than 58VDC, or larger than 10.5VDC.
Alarm current is 2A.
*Data Input
The upper ports 1-4 on the front panel are used for Gigabit Ethernet data input.
All four ports with surge protection.

User’s Manual TP-MS4x4 V5
TYCON POWER SYSTEMS
4
*Power Input
The input voltage of TP-MS4x4 is 12VDC to 57VDC, it is common negative design, the green
terminal (CON1) on rear panel is used for power input wiring, it can be connected to maximum 4
different sources with 4 different voltages, the jumper A, B, C, of JP1 on rear panel controls the
input/output connection, its setting as below. (1=jumper on, 0=off)
Jumper
Input
A
(1-2)
B
(1-3)
C
(1-4) PoE Output
VIN1+ 1 1 1 PoE 1/2/3/4=VIN1
(Factory setting)
VIN1+
VIN4+ 1 1 0 PoE 1/2/3=VIN1 PoE 4=VIN4
VIN1+
VIN3+ 1 0 1 PoE 1/2/4=VIN1 PoE 3=VIN3
VIN1+
VIN3+
VIN4+
1 0 0
PoE1/2=VIN1
PoE3=VIN3
PoE4=VIN4
VIN1+
VIN2+ 0 1 1 PoE1/3/4=VIN1 PoE2=VIN2
VIN1+
VIN2+
VIN4+
0 1 0
PoE1/3=VIN1
PoE2=VIN2
PoE4=VIN4
VIN1+
VIN2+
VIN3+
0 0 1
PoE1/4=VIN1
PoE2=VIN2
PoE3=VIN3
VIN1+
VIN2+
VIN3+
VIN4+
0 0 0
PoE 1=VIN1
PoE 2=VIN2
PoE 3=VIN3
PoE 4=VIN4

User’s Manual TP-MS4x4 V5
TYCON POWER SYSTEMS
5
*PoE Output
The bottom ports 1-4 on the front panel are used for carry PoE output, the output voltage is the
same as input, no regulated. Normally as detailed below:
* Data pair A on line 1 and 2
* Data pair B on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
*Output Polarity Reverse (for technician operation only)
The TP-MS4x4 may deliver PoE output with reverse polarity. Just move related jumpers from pin
1-2 to pin 2-3, and then
* Data pair C carry V- on line 4 and 5
* Data pair D carry V+ on line 7 and 8
Open the cover, the JP4~JP11 on the PCB responds for the output polarity of port 1~4, each two
jumpers should be paired moved to ensure the path enough for the through current.
JP10 & JP11 JP8 & JP9 JP6 & JP7 JP4 & JP5
Control port Port 1 Port 2 Port 3 Port 4
* Pin1-2(short pin1 & pin2): RJ45 pair C (pin4 & 5) carry PoE positive voltage.
* Pin2-3(short pin2 & pin3): RJ45 pair C (pin4 & 5) carry PoE negative voltage.

User’s Manual TP-MS4x4 V5
TYCON POWER SYSTEMS
6
4. Technical Information
Data Rate 10M/100M/1000M
Input voltage: 12VDC to 57VDC
Maximum PoE power Current limited – 1A/port
PoE protection over-current, over/under voltage
LEDs: Green-PD detect, Red-Power ready, Off-No power apply
Operating temperature -40℃~ +75℃
Operation humidity 90% relative humidity, non-condensing
Storage temperature -40℃~+85℃
Dimension 40mm(H) x118mm(W) x90mm(D) DIN RAIL Mountable
Surge protection on data input ports:
Signal
Operating Voltage Data 5V
Clamping Voltage
Data 16.5V (@I PP =5A, t p =8/20µs, I/O pin to GND)
Peak Pulse Current 20A (tp=8/20µs)
Pin Protected All 8 pin protected
Max. Shut Capacitance <3pF (VR = 0V, f = 1MHz, I/O pin to GND)
< 1.5 pF (VR = 0V, f = 1MHz, Between I/O pins)
IEC COMPATIBILITY (EN61000-4) IEC61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC61000-4-4 (EFT) 40A (5/50ns)
IEC61000-4-5 (Lightning) 20A (8/20µs)