U-Line H-3505 User manual

PAGE 1 OF 5 0514 IH-3505
πH-3505
GARAGE CANOPY
10'X20'X8'
1-800-295-5510
uline.com
CAUTION! Keep all flame and heat sources
away from tent fabric. The tent fabric will burn
if left in continuous contact with any flame
source.
DO NOT cook underneath or near canopy.
DO NOT store or use flammable liquids
underneath or near canopy.
DO NOT ignite or store fireworks underneath or
near canopy.
DO NOT use bleach to clean cover.
DO NOT dry clean cover.
DO NOT wash cover in washing machine or dry
in dryer. Hand wash with mild soap and water only.
DO NOT allow rain water, snow or ice to
accumulate on top of cover.
DO NOT hang or suspend anything from the
frame, grommets, truss system or ball straps of
the unit.
REMOVE canopy cover before a storm, or
disassemble entire canopy unit, if possible.
NOTE: This is a temporary structure and is
not recommended for use as a permanent
structure.
SAFETY
PARTS
Tape Measure
58" Pipe x 28 60' Rope For Assembly x 1
21.5" Pipe x 10
45" Curved Pipe x 20
2-way Corner
Foot Pad x 4
3-way End
Connector x 10
Ball Straps x 70
Cables x 5
Wrench or Socket
9/16"or 14mm
Phillips Screwdriver
TOOLS NEEDED
Rubber Mallet
Safety Glasses
3-way Center
Foot Pad x 6
4-way Center
Connector x 15
Cover x 1 Back Wall
With Zippers x 1
Screw-in
Ground
Anchor x 6
Front Wall
With Zippers x 1
Stake x 10

PAGE 2 OF 5 0514 IH-3505
NOTE: For faster and easier set up, assembly by
two or more people is recommended.
1. Lay parts out as shown. (See Figure 1)
NOTE: The 58 inch straight pipes form the
length of the frame. The 21.5" straight pipes
are the legs that connect to the feet.
NOTE: Longest part of 3-way is used to form
the length.
NOTE: The two longest parts of the 4-way are
used to form the length.
2. Assemble the first frame section using the 45"curved
pipe and the 58" straight pipe. (See Figure 2) Make
sure longest parts of 3-way and 4-way are used to
form length. Continue assembly until you have 4
sections complete, which is the full length of the unit.
(See Figure 2)
3. After assembling the first full length section of
roof, use the rope to hold frame together.
(See Figure 3A)
Tie frame from end to end down the center.
(See Figure 3B)
4. Continue assembly by completing the next
curved section on each side of the top section.
(See Figure 4) Hold frame together by tying frame
from end to end at the bottom of section.
NOTE: Push frame inward from each side to
keep curved shape.
5. Once you have completely assembled all curved
sections of the canopy (See Figure 5), you are now
ready to put the cover on.
NOTE: Put cover on before assembling the last
section with feet. See next step.
FRAME ASSEMBLY
33.5"
Straight Pipe
58"
Straight Pipe
All Horizontal Pipe
3-way
Connectors
3-way
Foot
4-way
Connectors
2-way
Foot
Figure 1
45" Curved
Pipe
58" Straight
Pipe
4-way
Connector
3-way Connector
Figure 2
Figure 3A
Figure 3B
Figure 4
Figure 5

PAGE 3 OF 5 0514 IH-3505
1. Remove cover from plastic bag and unfold. Next
fold half the cover over the other half with the
white side out. Match the corners (See Figure 6A)
and mark the top center of cover at the grommet
line at both ends. (See Figure 6B)
2. Once centers have been marked at both ends, pull
cover over frame with white side down. (See Figure 7)
3. Position the center mark with the top center pipe
of frame.
4. Attach cover to each end of top curved frame by
running ball strap through grommet hole, around
pipe and hook back over ball. (See Figures 8-9)
5. Once you have secured top to curved section
of frame, finish frame assembly. Assemble the
remaining frame on each side using the 21.5" pipe,
foot pads and 58" pipe. (See Figure 10) Make sure
hooks on the feet are on the inside of frame. Push in
on leg sections and make sure the legs are securely
set on ground before assembling final side and
standing canopy up. This will keep the canopy
from sliding.
6. Now that you have completed the frame assembly
and your canopy is standing, take the cables
provided and hook one end to each foot
(See Figure 11-12), over to the foot on the opposite
side. You may have to push out or pull in to get
cables hooked. Make sure cables are tight across.
These cables keep the canopy frame with the
designed curved shape.
NOTE: Be careful NOT to trip over cables.
COVER AND LEGS ASSEMBLY CONTINUED
Figure 9
Inside View Outside View
Figure 7
Figure 10
Figure 12
Fi gu re 11
Figure 8
Figure 6B
Figure 6A

PAGE 4 OF 5 0514 IH-3505
CAUTION! This canopy is designed for use as
a temporary structure. After assembly, the
canopy MUST BE securely anchored to the
ground to prevent damage from winds. Your
canopy will act like a kite in the wind if not
properly and securely anchored to the ground.
Severe winds will cause the frame to twist and
unanchored legs will fall; thereby collapsing
the canopy. If severe winds are expected, you
must remove the cover from the frame to
prevent damage.
1. Anchor your canopy at each corner foot and center
foot on each side. Screw anchor into ground next to
canopy foot using a large screw driver.
(See Figure 17)
Looping the cable through the anchor eye will keep
it out of the way while turning. Tilting the anchor
slightly will help the anchor to cut into the ground.
Apply downward pressure while turning the anchor
into the ground. Leave approximately three inches
of anchor out of the ground.
COVER AND LEGS ASSEMBLY CONTINUED
ANCHORING THE UNIT
7. With the canopy standing and cables in place,
anchor the canopy using the foot stakes provided.
(See Figure 13) Driving the stakes in at an angle will
help anchor the canopy more securely. Once stakes
are in place, you may remove the cables.
SEE "ANCHORING THE UNIT"
8. To complete your canopy, secure the top down
each side on the bottom pipe and around each
end with ball straps. (See Figure 14)
9. Add the canopy end walls using the Velcro straps
and then secure them using the ball straps. Next,
tighten and secure the drawstrings at each corner
foot. You have successfully set up your canopy
(See Figure 15). Now that the canopy is set up, you
may remove the ropes used for frame assembly.
NOTE: Your canopy sidewalls and rear end wall
are long enough to be buried in the ground.
This will help prevent water from running inside.
(See Figure 16)
Figure 13
Fig u re 17
Figure 15
Figure 16
Figure 14

PAGE 5 OF 5 0514 IH-3505
2. Unloop the cable from the anchor eye and slide
the clamp onto cable. Run cable around the
pipe, (See Figure 18) and then back through the
clamp. (See Figure 19) Pull the cable as tight as
possible through the clamp. Hold the cable and
tighten clamp with a 5/8"wrench or some type of
adjustable wrench.
3. When you have tightened the clamp and satisfied
that the cable will not slip, you may tighten the
cable more by turning the anchor further in the
ground. (See Figure 20)
Improper Anchoring, Strong Winds, Rain Snow, or Ice
King Canopy/PIC America, LTD. does not guarantee these canopies under
strong weather conditions. These canopies are designed to protect against
damages caused by sun, rain, tree sap, birds, etc. They are not designed to
hold roof loads that accompany snow, ice or heavy rains. If your canopy is
not anchored securely, it can be lifted by the wind and will fly away. If your
canopy takes flight, we are not responsible for any replacement. If strong
weather is predicted, remove the cover or take down the canopy unit
completely. The cover is designed to be quickly and easily removed.
ANCHORING THE UNIT CONTINUED
Figure 18
Figure 19
Figure 20
π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA
1-800-295-5510
uline.com