U-tec Ultraloq UL3 User manual

Ultraloq UL3
Fingerprint and Touchscreen
Smart Lock
Installation Instructions ( V1.3 )
Welcome

Important Notes
• Only use a power drill for making a hole.
Do not use it for installation. 
• Install and test the lock with the door open to avoid being
locked out.
• Please read all the instructions before contacting customer
support.
• Please contact customer support before returning the
product to the store.
• DO NOT install the batteries before installing the lock! Follow
the instructions in sequential order!
• If you have previously installed this lock on another door, you
must perform a Factory Default Reset FIRST! See the User
Guide for more information.
• This lock is designed for the following operating tempera-
tures:
• Outside Lock Body (exterior mounted): -31˚F (-35˚C) to
158˚F (70˚C)
• Inside Lock Body (interior mounted): 14˚F (-10˚C) to 131˚F
(55˚C)
Please watch our easy step by step installation video
before attempting to install your Ultraloq UL3 Fingerprint
and Touchscreen Smart Lock.
If you have questions regarding the installation process
Please contact us at [email protected]
- 1 -
Installation Video
www.u-tec.com/support
Need Help?
For technical documents and more
Please visit www.u-tec.com/support
Tel: 844-HEY-UTEC (844-439-8832)
Email: [email protected]

Included in the box
Exterior
Assembly
LatchStrike
Screw A Screw B Screw C Screw D Screw E
Backup Keys
Interior
Assembly
Interior
Mounting Plate
Spindle
Handle Drill Screwdriver
AA alkaline
AA Batteries
- 2 -
Spring

Check the door’s dimensions
Drill a hole in the door
Use the Drill Template
provided in the box.
- 3 -
23
/
4”
23
/
8”
(70 mm)
(35 mm-44mm)
OR
(60 mm)
21
/
8”(53 mm)
Hole
1” (25 mm)
Door Edge
Preparing Door
13
/
8
” 13
/
4
”
~
!

If your door thickness is over 16.5”(42mm),
Please install this spring.
- 4 -
Preparing Door
Interior
Spring ×1
!

Screw A
Screw A
Installing Latch and Strike
Before installing the lock on the door
- 5 -
60~70mm
Adjust the latch
basket length
Angle faces jamb
1. Install latch on the door. Make sure the latch
angle faces door jamb.
2. Install the strike on the door frame, ensuring you
allow for the bolt to be centered in the strike.
1. Loosen the screw holding the battery cover.
2. Slide the battery cover up and out (note the two tabs at the
bottom of the battery cover).
3. Remove the inside mounting plate (with gasket) from the
back (door side) of the interior assembly.
2

- 6 -
1. Install the exterior assembly.
Route the cable under bolt and through hole stated below.
Installing Exterior Assembly
3

Route wire over the hole
Plug in the spindle
- 7 -
Screw B
1. Install interior mounting plate.
Secure it to the exterior assembly using screws.
2. Plug in the spindle.
4
Installing Interior Mounting Plate
3

Installing Interior Assembly
Screw D
Screw C
Connect the cable
- 8 -
5
1. Attach the cable to the interior assembly printed circuit
board (PCB) by lining up notches on the cable connector
to slots on the PCB connector. Press the connector in
firmly using thumbs until completely seated.
2. Secure interior assembly using screws.

Installing Batteries
AA alkaline
- 9 -
1. Insert 3 AA alkaline batteries.
2. Install battery cover and tighten the screw.
6
Screw E

Installing Handles
- 10 -
1. Press lever handles onto handle posts.
2. Test the mechanical operation of the lock by rotating
handle from inside. The movement of the bolt should be
smooth and unobstructed. If the operation is not smooth,
review the previous steps to ensure proper installation.
If the handles are installed in the wrong direction, you
need to remove them and re-install.
To remove the handle, you need to insert the screwdriver
into the hole in the handle, push in and hold. Then pull the
lever handle out.
Congratulations!
You have installed the Ultraloq UL3
Fingerprint and Touchscreen Smart Lock successfully.
7

7
Handle plug position
- 11 -
The handle is not fully plugged in.
The handle is plugged in correctly.
!
or

Note
Date / /

Note
Date / /

Note
Date / /

U-tec and Ultraloq brands and products are trademarked
and protected under law in the United States.
Unauthorized use is prohibited.
2016 © U-tec Group Inc. All Rights Reserved.
Ultraloq is sub-brand of U-tec Group Inc.