U-tec UltraloqUL3 User manual

Ultraloq UL3
Fingerprint and Touchscreen
Smart Lock
User Guide ( V1.3 )
Welcome

- 1 -
Register Your Lock
To ensure the best warranty coverage and customer
service, please register your product at
http://store.u-tec.com/account/login
Warranty Statements
See www.u-tec.com for specific warranty details and
limitations, or contact U-tec’s Customer Service .
* This guide contains important information about your lock!
Operation Video
Please watch our easy step by step operation video
before attempting to use your Ultraloq UL3 Fingerprint
and Touchscreen Smart Lock.
If you have questions regarding the installation process
please contact us at [email protected]
www.u-tec.com/support
Need Help?
For technical documents and more
Please visit www.u-tec.com/support
Tel: 844-HEY-UTEC (844-439-8832)
Email: [email protected]

- 2 -
Exterior
Interior
Lock Parts
Touchscreen
Fingerprint reader
Message display screen
Backup key hole
Restart button
Battery Cover
Reset Button
SN Label
Reset Button: Used to reset the lock to factory default settings.
Battery Cover: Used to cover battery and product label. A Quick Guide
is printed inside the battery cover.
Backup Key Hole: Used to insert the key to unlock.
Restart Button: Used to jump start the lock if activation fails.
Fingerprint Reader: Used to press finger and unlock from the outside.
Touchscreen: Used to enter the code and unlock from outside.
- Numbers Return to previous Confirm
0 9

Lock Operation
- 3 -
1. Touch lock with back of hand or fingers to activate the lock.
2. Input user PIN code to unlock.
3. Rotate handle and open the door.
Open door from outside with
user PIN code
Press finger on fingerprint reader or touch lock with the
back of hand or fingers.
The lock will turn off again after 20 seconds if there are
no other inputs.
Use a microfiber cloth and wipe across the fingerprint
reader surface and the touch screen.
Clean the fingerprint reader and
touchscreen
Lock Activation

1. Press finger on the fingerprint reader to activate and unlock.
2. Rotate the handle and open the door.
Open door from outside with
fingerprint
1. Rotate the handle and open the door.
Open door from inside
- 4 -
When you activate the lock and see the message “Low
battery”, you should replace the batteries.
Use 3 high-quality alkaline AA batteries for replacement.
Replace battery
Emergency Key Override can be used when the battery is
dead, or when no valid User Code is known.
The key hole is on the bottom of the lock. Insert the key and
rotate to unlock, just like any lock. Take good care of your
emergency keys.
Emergency Key Override

Ultraloq UL3 supports up to 16-digit Vague Code.Just enter
any 16-digit code, as long asa correct codeis included in
what you entered, you canopen the door.
Vague Code
1. Place a finger flat on the sensor’s surface.
2. Place a finger in the center of the sensor.
Place Finger
- 5 -
1:
2:
3:
1 2 3 4 5 6 X X X X X X
1 2 3 4 5 6
X X X X X X
1 2 3 4 5 6
X X X X X X
Example
User Code:123456
Vague Code Method

Admin account must be created first before any other
programming.Then use the Admin account to add or delete
the other accounts.
Register Admin and User
Factory default setting is that any fingerprint or PIN code
can open the door.
Factory Defaults
Lock Programming
- 6 -
User PIN code can be 4 to 8 numbers.
User PIN code
User ID can be 1 to 8 numbers.
User ID number
You can register up to 95 users with fingerprint and PIN code.
Limit the number of users on lock
1. Activate lock. Press and hold for 3 seconds to into menu.
2. Input number to select functions:
3. Press and follow the displayed messages to setup.
Basic programming steps
1to add User
to delete User
to add Admin
to delete Admin
2
8
7
Reset the lock
Remove the battery cover. The reset button is under the
serial number label. Find a small paper clip and stick one end
into the reset button hole while the lock is active. Press and
hold the reset button for 3 seconds until a beep is audible.
All user info will be deleted.

Add Admin First
- 7 -
Admin account must be created first prior to
any other programming.
Activate Lock No User
Add adminPress and hold for 3 sec
Finger or codePress
Enter againPress finger or input a PIN code
SuccessPress finger or input a PIN code
1

Add User
- 8 -
Activate Lock Welcome
Admin codePress and hold for 3 sec
MenuPress admin finger or enter admin PIN code
Add userPress 1
Press Enter user ID
Enter user ID Finger or code
Press finger or input a PIN code Enter again
Press finger or input a PIN code Success
2

Delete User
- 9 -
Activate Lock Welcome
Admin codePress and hold for 3 sec
Press admin finger or enter admin PIN code Menu
Delete userPress 2
Press Enter user ID
Enter user ID Enter again
Enter user ID again Success
3

Add Admin
- 10 -
Activate Lock Welcome
Admin codePress and hold for 3 sec
Menu
Press admin finger or enter admin PIN code
Press Finger or code
Press finger or input a PIN code Enter again
Note: It is recommended to register several Admin
fingerprints and PIN codes.
Press finger or input a PIN code Success
Add adminPress 7
4

Delete Admin
- 11 -
Activate Lock Welcome
Admin codePress and hold for 3 sec
Menu
Press admin finger or enter admin PIN code
Press Finger or code
Press admin finger or enter admin PIN code Success
Delete adminPress 8
5

Keep Your Records
DATE ADMIN CODE
NAME
Will Smith 100001 8765432
Example
USER ID USER CODE
√
Note: It is recommended to register several Admin
fingerprints and PIN codes.

Keep Your Records
DATE ADMIN CODE
NAME
Will Smith 100001 8765432
Example
USER ID USER CODE
√
Note: It is recommended to register several Admin
fingerprints and PIN codes.

Note
Date / /

U-tec and Ultraloq brands and products are trademarked
and protected under law in the United States.
Unauthorized use is prohibited.
2016 © U-tec Group Inc. All Rights Reserved.
Ultraloq is sub-brand of U-tec Group Inc.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.