UbiTech Custos BVSLWU User manual

3
1
4
2
BALL VALVE SERVO INSTALLATION
BALL VALVE SERVO INSTALLATION GUIDE
Do NOT use on other types of valves.
1. CLOSE VALVE
2. PREPARE YOUR BVS
3. INSTALL BVS ON YOUR VALVE
4. CONNECT SPC AND POWER ADAPTER
Touch Sense Button
if you have oversized valve or your valve has adjacent pipe elbow, you may
slide any or both clamps in or out to fit the space.
1
Make sure the knobs are
facing on the same side as
the water valve handle
2
Check the transmission fork mechanic engagement by visual
You SHOULD NOT see the PATTERN on the top of transmission fork, if you do, you
may not install it securely, please double check, make sure you have pushed the BVS
down enough for a secured installation.
Otherwise you have a rare ultra low profile valve, the handle is too low for spring
loaded mechanic to engage, in this case, please put the Spacer between the hex
bolt head of the valve and the transmission fork.
If you don’t see the pattern without Spacer, DO NOT use the Spacer.
PATTERN NOT SEENPATTERN SEEN
Rotate the handle from position to position to turn off your valve
1 2
Align the pivot of the transmission fork is with the hex bolt
on top of the valve Press down firmly to engage the spring
loaded gear, then tighten 2 clamps.
Position the BVS over the top of the handle of ball valve
1
2
1
2
If you are installing the Ball Valve Servo outdoor, you may consider to disable the
touch sensing button to prevent it activated from rain drops or pets.
To Disable the button:
Tap and hold the touch sense button for 3 beeps, then quickly tap 3 times in a row.
If successful, the Yellow LED will flash once, then the Red LED with 1 beep. The LED
will slowly flashing Yellow indicating the touch sense button has been locked.
To Re-Enable the button:
Tap and hold the touch sense button for 3 beeps, then quickly tap 3 times in a row.
If successful, the Yellow LED will flash once, then the Red LED with 3 beeps. LED will
then slowly flashing Green indicating the touch sense button has been unlocked.
PACKAGE CONTENTS
Ball Valve Servo (BVS)
Water Detection Probe 55.1 inch
3
4
1
2 Power Adapter
Spacer
1
You may install local water detection probe (included) for close area leak detection, plug the male
jack to the female jack from the power supply cable branch, It will trigger the valve to close
whenever water is detected. (remove the protection cap from female jack first)
1 2
2
If you have purchased Smart Power Capsule, connect it
between Ball Valve Servo and power adapter. SPC is the
optional back up power device, it provides up to 32 hours of
back up power for BVS if there is a power failure.
Insert the male jack into the
water tight female jack with
extra force to secure contact and
water proof result
1
2

Contents
USER GUIDE
1 INTRODUCTION ..........................................................................................................................................................
1.1 Custos BVS ...............................................................................................................................................................
1.2 Connectors & Interfaces..............................................................................................................................................
2 SPECIFICATIONS ........................................................................................................................................................
2.1 Physical Specifications...............................................................................................................................................
2.2 Hardware Specifications .............................................................................................................................................
3 WORKING MODE & FEATURES.....................................................................................................................................
3.1 Standalone Mode.......................................................................................................................................................
3.2 Network Mode ...........................................................................................................................................................
3.3 Ball Valve Actuator......................................................................................................................................................
3.4 Water Leak Sensor & Alarm ........................................................................................................................................
3.5 Ambient Temperature Sensor.......................................................................................................................................
4 KEY & INDICATORS BEHAVIOR ....................................................................................................................................
4.1 Touch Sense Button ...................................................................................................................................................
4.2 Visual Indicator .........................................................................................................................................................
4.3 Sound Indicator .........................................................................................................................................................
5 TOUCH SENSE BUTTON KEYLOCK...............................................................................................................................
5.1 Touch Sense Button Keylock Enable ............................................................................................................................
5.2 Touch Sense Button Keylock Disable............................................................................................................................
6 WATER VALVE OPERATION .........................................................................................................................................
6.1 Manual Calibration Valve Position ...............................................................................................................................
6.2 Turn Valve to OPEN ...................................................................................................................................................
6.3 Turn Valve to CLOSE ..................................................................................................................................................
6.4 Pause OPEN/CLOSE Operation ..................................................................................................................................
6.5 Resume OPEN/CLOSE Operation ...............................................................................................................................
7 WATER LEAK SENSOR & ALARM ..................................................................................................................................
7.1 Water Leak Detection & Alarm .....................................................................................................................................
7.2 Water Leak Alarm Cancellation ...................................................................................................................................
8 TEMPERATURE SENSOR .............................................................................................................................................
9 APPENDIX....................................................................................................................................................................
9.1 System Event Status ..................................................................................................................................................
9.2 Touch Sense Button Keylock .......................................................................................................................................
9.3 Operation Mode .........................................................................................................................................................
9.4 Water Valve Operation & Status...................................................................................................................................
9.5 Water Leak Event & Alarm ...........................................................................................................................................
9.6 Patents .....................................................................................................................................................................
9.7 Cautions ...................................................................................................................................................................
9.8 Warranty ...................................................................................................................................................................
9.9 Disclaimer .................................................................................................................................................................
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
3
3
3
3
3

1.1 Custos BVS
2.1 Physical Specifications
Model No. BVSLWU (US)/ BVSLWE (EU)
Dimensions 14.8x9.6x13.3mm
Weight BVS Unit: 603g
Body Color White
Knob Color Light blue
Waterproof & Dustproof IP66 level / Outdoor deployment
Usage For Indoor and Outdoor Water Valve On/Off
Operation Temperature 14~122 ℉ (-10~+50℃)
Relative Humidity 8%~80%
2.2 Hardware Specifications
RF Module Sx1261
RF Distance 40m/131inch (Indoor) /120m/394inch(Outdoor)
Region Frequency US: 915, FCC CFR47 Part 15.249 EU: 868
Motor Torque Power Adaptive torque output max: 8n.m
Water Leak Sensor Local Water Leak Sensor Probe
Temperature Sensor Built-in temperature sensor, Range from -40°C to +125°C / (-40°F to +257°F)
Action Button Touch Sense Button x 1
LED & Sound Indicator 3 colors LED. (Green, Yellow & Red); Buzzer (Max. 85dB)
Power Supply AC-DC: AC (110V 60Hz / 220V 50Hz); DC (12V / 1A)
Power Consumption Standby: ~10mA@12VDC=0.12W Full Operation: Max~700mA@12VDC=8.4W
1 INTRODUCTION
2 SPECIFICATIONS
Custos Ball Valve Servo “Custos BVS” is capable for outdoor deployment for
controlling water valve OPEN / CLOSE. It also supports auto CLOSE valve when
water leak is detected by Local Leak Sensor Probe.
ac
d
e
fg
h
j
k
l
b
Type A Type B
Depend on region and valve types there
are 2 types of driving forks
iDriving fork
4 KEY & INDICATORS BEHAVIOR
3.1 Standalone Mode
- The LED indicator stays with Yellow blinking without joining the LoRaWAN
network or lose the network connection.
- Support OTAA, Water Valve Operation, Water Leak detection & Alarm.
3.2 Network Mode
- LED indicator stays in Green Heartbeat “Fade-in & Fade-out” after joined
LoRaWANnetwork.
3.3 Ball Valve Actuator
3.4 Water Leak Sensor & Alarm
3.5 Ambient Temperature Sensor
- Support OPEN, CLOSE, PAUSE
- RESUME during OPEN/CLOSE operation.
- Manual Calibration position of valve handle. (Only support operate by Touch
Sense Button)
- Water Valve will be closed automatically once Local Water Leak Sensor Probe
is triggered.
- Water Leak Alarm will be activated and to CLOSE Water Valve automatically
once Local Water Leak is detected.
- Once Local Water Leak is detected then BVS will also send out Heartbeat
through LoraWAN network.
- By default, BVS sends temperature report automatically to gateway when every
1°C or 1.8°F degree changed.
Sound indicator Buzzer
Temperature sensor Built-in temperature sensor
Visual indicators 3 Colors LED with green, yellow & red
Touch sense button Network, water valve and alarm operations
Knob Use to adjust Clamp widths
Device EUI Device EUI
1.2 Connectors & Interfaces
Product label Product info and serial number
Clamp Clamp on water pipe. Max 1-1/4 inch
Driving fork Couple with valve handle
Power connector DC 12V / 1A in
Dust cover Prevent Dust and Water
Leak sensor connector Local leak sensor probe
a
c
d
e
f
g
h
j
k
l
b
i
PAGE 1
Ub itech Ltd. Version: 2.0
3 WORKING MODE & FEATURES
Dev EUI
FCC ID: 2AUZX-BVSLWU
DC12V 1A
BVSLWU
Ball Valve Servo
IP66
US902-928Mhz
Assembled in China S/N: 12345 6789 012
This device compiles with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2)This device must accept any interference received,
including interference that may cause undesired operation.
33373835aabbccdd
Designed by
5 TOUCH SENSE BUTTON KEYLOCK
Custos BVS is capable for outdoor deployment. To prevent mis-operation by rain
drop, end-user can enable Touch Sense Button Keylock function to forbid the
operation of Touch Sense Button until to disable the keylock function.
After enabled Touch Sense Button Keylock function, Custos BVS will ignore all
key events excepting Touch Sense Button Keylock Disable function (Refer to 5.2)
i. Start: Long hold Touch Sense Button 3 seconds then short click 3 times.
ii. Process: Yellow LED on 1 second then Red LED on 1 second with 3 beeps
iii. Success: Yellow LED Fade-in and Fade-out.
i. Start: Long hold Touch Sense Button 3 seconds then short click 3 times.
ii. Process: Green/Yellow/Red LED blink one by one with 3 beeps.
iii. Success: LED indicator resume previous status. (Green LED slow blinking or
Yellow LED blinking)
5.1 Touch Sense Button Keylock Enable
5.2 Touch Sense Button Keylock Disable
4.1 Touch Sense Button
4.2 Visual Indicator
4.3 Sound Indicator
- Short Press: One click comes with one short beep sound.
- Long Hold: Press and holding the key. “Come with 1 x short beep sound per
second”
- 3 Colors LED: GREEN, YELLOW & RED
- ON Event: ON, quick blinking and slow blinking and “Fade-in & Fade-out”
Buzzer: Long & short beep sound.
6.1 Manual Calibration Valve Position
Calibration function will identify the correct OPEN/CLOSE position and torque
force, it will avoid excess stress applied to the valve. By default, BVS will perform
Auto-calibration when re-power on every time.
i. Start: Long Hold Touch Sense Button 5 seconds, then short click 5 times.
ii. Processing: Water Valve run OPEN and CLOSE 1-2 cycles, Yellow LED blinking
and quick short beep sound keep continue.
iii. Success: The LED indicator changes to Yellow LED blinking.
6 WATER VALVE OPERATION

6.2 Turn Valve to OPEN
6.3 Turn Valve to CLOSE
6.4 Pause OPEN/CLOSE Operation
Turn Valve to OPEN position and let water run through the pipe.
i. Start: Short click Touch Sense Button 1 time.
ii. Processing: Water Valve turning to OPEN position, Green Heartbeat LED
“Fade-in & Fade-out” and short beep sound keep continue.
iii. Success: The LED indicator changes to Yellow LED blinking
Turn Valve to CLOSE position and don’t let water run through the pipe.
i. Start: Short click Touch Sense Button 1 time.
ii. Processing: Water Valve turning to CLOSE position, Yellow Heartbeat LED
“Fade-in & Fade-out” and short beep sound keep continue.
iii. Finished: The LED indicator changes to Yellow LED blinking
Pause only take effect during OPEN or CLOSE operation.
i. Start: Short click Touch Sense Button 1 time.
ii. Processing: Yellow LED blinking and Valve stop operation.
6.5 Resume OPEN/CLOSE Operation
Resume only take effect during Pause operation.
i. Start: Short click Touch Sense Button 1 time.
ii. Finished: Valve resume to operation (Continue to Opening / Closing) and LED
indicator changes to LED Yellow/Green Heartbeat.
7 WATER LEAK SENSOR & ALARM
7.1 Water Leak Detection & Alarm
Custos BVS comes with Local Leak Sensor Probe and support following functions,
in short, once Water Leak is detected, Water Leak Alarm will be activated, hence
the water valve will be closed spontaneously, at this moment all other operations
will not be accepted except Water Leak Alarm Cancellation.
i. Activated Water Leak Alarm
- RED LED fast blinking.
- Fast beep sound.
ii. CLOSE Water Valve automatically
iii. Send out Heartbeat
iv. Water Valve keeps in CLOSE position
v. The operation is forbidden temporally until perform Water Alarm Cancellation
operation. (Refer 7.2)
7.2 Water Leak Alarm Cancellation
Water Leak Alarm Cancellation operation only accepted when Local Water Leak
Sensor Probe is no longer detected water.
i. Start: Long hold Touch Sensor Button 2 seconds
ii. Success: The LED indicator changes to previous status. (Yellow LED blinking
or Green LED slow blinking and buzzer goes silence.)
iii. Send out Heartbeat
Ub itech Ltd. Version: 2.0
PAGE 2
8 TEMPERATURE SENSOR
i. By default, Custos BVS will send out Heartbeat automatically when temperature
in 1°C or 4°F change of ambient temperature.
ii. Custos will send out °F in US version and °C for other versions.
9.3 Operation Mode
Operation
Mode
Water Valve
Manual
Operation
Key Action Operation Support
Long Short Standalone Network
Open Control water valve to full open --- 1 Support Support
Close Control water valve to full close --- 1 Support Support
Pause Pause only works during open/close operation --- 1 Support Support
Resume Resume to previous during Pause operation --- 1 Support Support
Auto-calibration Perform calibrate position and torque force 5 5 Support Support
Trigger to close valve Auto close water valve --- 1 Support Support
Alarm Cancellation 2 --- Support Support
Resume to normal operation
mode if no alarm triggered
Water Leak
Alarm
Function Description
9 APPENDIX
9.1 System Event Status
9.2 Touch Sense Button Keylock
Terminology, all events and operations details including action key event, LED and buzzer
Event Detail LED Buzzer
System Ready BVS is Ready to operate after power on or reset. Green LED ON 2 seconds 2 beep sounds
Standalone mode heartbeat Standalone Heartbeat without network connection Yellow LED blinking ---
Event Success Finished operation and success Green LED ON 2 seconds Short beep x 2
Event Error Operation fail or not available RED LED blinking 3 times Long beep x 3
Event Timeout Operation timeout RED LED ON 1” Pulse sound
9.4 Water Valve Operation & Status
PAUSE Only available during
Open/Close operation
Event Action / Status Key Action LED Status Buzzer Status
Start OPEN (Valve in closed position) Click 1 time Yellow LED keep blinking —
Processing --- Yellow LED keep blinking Keep short beep
Success --- Green LED ON 1 second Short beep x 2
Next status (In Network Mode) --- Green LED slow blinking —
Next status (In Standard Mode) --- Yellow LED slow blinking —
Start CLOSE (Valve in open position) Click 1 time Green LED ON 1 second 1” Pulse sound
Processing --- Yellow LED keep blinking Keep short beep
Success --- Green LED ON 1 second Short beep x 2
Next status(In Network Mode) --- Green LED slow blinking ---
Next status (In Standard Mode) --- Yellow LED slow blinking ---
Click 1 time Short beep x 1
Processing-“In Network Mode” --- Yellow LED slow blinking ---
Next status – “In Network Mode” --- Green LED keep blinking ---
Processing – “In Standalone Mode” --- Yellow LED keep blinking ---
Next status – “In Standalone Mode” --- Yellow LED keep blinking ---
Click 1 time Green LED ON 1 second Short beep x 1
Next Status – Return Open/Close --- Yellow/Green LED blinking Keep short beep
Start Manual Calibration --- ---
Processing–Open&Close 1-2 cycles --- Yellow LED keep blinking Keep short beep
Next status – “In Network Mode” --- Green LED slow blinking ---
Next status – “In Standalone Mode” --- Yellow LED keep blinking ---
OPEN Valve
GreenLED ON 1 second
CLOSE
Valve
PAUSE
Operation
RESUME
Operation
Manual
Calibration
Start RESUME available during
Open/Close operation
Hold 5 sounds &
click 5 times
Event Action/Status Key Action LED Status Buzzer Status
Start Water Leak Alarm --- RED LED fast blinking Fast beep sound
— RED LED fast blinking Fast beep sound
Alarm Cancellation Green LED blinking 2 times Short beep x 2
Success cancellation --- Green LED blinking 3 times Short beep x 3
Next Status–“In Network Mode” --- Green LED slow blinking —
Nest Status – “In Standalone Mode” --- Yellow LED blinking —
Processing – Close Water
Valve automatically
Long hold 2 seconds
Leak Alarm
Cancellation
Leak Sensor
Probe
Triggered
9.5 Water Leak Event & Alarm
9.6 Patents
Patent 1: US 11,233,501 B1
Patent 2: US 10,995,876 B2
9.7 Cautions
MOVING PARTS WARNING: Keep hands, hair and all loose articles of clothing away from moving parts.
Moving parts can cause serious Injury. Maintain a safe distance from the product during its operation to
eliminate risk of injury.
POWER SUPPLY WARNING: The power supply is for indoor use only. Only use power supply included
with your product. Do not attempt to repair or use a damaged power supply. Do not immerse the power
supply in water or subject it to physical abuse. Inspect the power supply regularly for cable, plug damage.
CORRECT DISPOSAL OF BATTERIES IN THIS PRODUCT: This marking on the product, accessories or
literature indicates that the product and its electronic accessories should not be disposed of with other
household waste. To prevent possible harm to the environment or human health from uncontrolled waste
disposal, please separate these items from other types of waste and recycle them responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
government office, for details of where and how they can take these items for environmentally safe
recycling.
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product and its electronic accessories should not be mixed with other wastes for disposal.
This marking on the battery, manual or packaging indicates that the batteries in this product should not be
disposed of with other household waste. Where marked, the chemical symbols Hg, Cd or Pb indicate that
the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.If
batteries are not properly disposed of, these substances can cause harm to human health or the
environment.
SAFE USAGE GUIDELINES: Do not modify or open the product except for battery removal and
replacement. Do not disassemble or attempt to service this product. This product is safe under normal
and reasonably foreseeable misuse operating conditions. Always use both hands while operating the
product. This is not a children's product and is not intended for use by children. Product must be returned
to the manufacturer for any service or repair. Long periods of repetitive motion using the product may be
associated with nerve, tendon or muscle injury in your hands, wrists, arms, shoulders, neck or back. See
a qualified health professional for pain, numbness, swelling, burning, cramping or stiffness.
Event Action/Status Key Action LED Status Buzzer Status
Keylock Enable Enable Lock Key Function Long beep x 1
Success–“In Network Mode” --- ---
Success– “In Standalone Mode” --- ---
Keylock Disable Disable Lock Key Function Long beep x 3
Success–“In Network Mode” --- Green LED slow blinking ---
Success – “In Standalone Mode” --- Yellow LED blinking ---
Hold 3 seconds&
click 3 times
Yellow LED ON 1 second
Red LED ON 1 second
Hold 3 seconds&
click 3 times
Green/Yellow/Red LED blink
one by one with 3 beeps
Yellow LED Fade-in &
Fade out
Yellow LED Fade-in &
Fade out

PAGE 3
Ub itech Ltd. Version: 2.0
9.9 Disclaimer
DISCLAIMER
We hereby disclaim that the product is not a substitute for homeowner insurance, customers still
need to purchase relevant insurance, due to installation conditions, environment and other
reasons beyond our control, we cannot guarantee that the product/solution can 100% prevent
water leakage in all situations damage, users losses will be beyond of our liability. Ubitech
assumes no responsibility for any errors that may appear in this manual. Information contained
herein and in the set-up guide is subject to change without notice.
Ubitech logo is registered trademark of Ubitech Limited
CUSTOMER SERVICE
If you have any questions, our trained Customer Service Department is happy to assist you 24
hours a day, 7 days a week. Contact Ubitech Customer Service as follows:
Address: Flat 12, 7/F Block A, Hi-Tech Industrial Centre,
5-21 Pak Tin Par Street, Tsuen Wan, N.T. Hong Kong
Email: [e-mail]
Call: [phone]
9.8 Warranty
STATEMENT OF WARRANTY: 1 Year Limited Warranty
Ubitech Limted ("Ubitech”) warrants to the original retail purchaser ("Purchaser”) that the
Ubitech (the “Product”) will be free of defects in materials or workmanship under use for one (1)
year from the date of purchase (the “Warranty period").
For the Purchaser only, if the Product fails to perform as specified during the Warranty Period
due to defective parts or faulty workmanship, Ubitech will repair or replace the defective or
damaged parts of the Product. Normal wear and tear is not covered nor is abnormal use, misuse,
mishandling, faulty installation, improper shipping, damage caused by disasters such as fire,
flood or earthquake, neglect, accident or tampering. This warranty covers only normal use in the
United States or Canada.
To obtain warranty service during the Warranty Period, call Ubitech Customer Service + -852
81008500 or email: [e-mail] for instructions on sending damaged parts and
documentation for a Return Merchandise Authorization (RMA). Products returned to Ubitech for
repair or replacement without authorization will be returned at the sender's expense. All
warranty claims must be accompanied by a legible copy of the original receipt showing date and
details of purchase.
THIS WARRANTY IS NOT TRANSFERABLE, AND, TO THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW IS IN LIEU OF ALL OTHER WARRANTIES, REPRESENTATIONS AND
CONDITIONS, EXPRESSED OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING BUT
NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. NO OTHER PERSON OR REPRESENTATIVE IS AUTHORIZED TO
MAKE ANY OTHER WARRANTY ON BEHALF OF UBITECH OR ASSUME FOR UBITECH ANY
OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. IN NO EVENT WILL
CUSTOS BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PRODUCT, INCLUDING DAMAGES DUE TO UBITECH'S NEGLIGENCE. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE AND COUNTRY TO COUNTRY.
DO NOT RETURN THIS PRODUCT TO THE STORE OR WEBSITE FROM WHICH IT WAS
PURCHASED If you believe the product is defective, has a missing or broken part or are having
difficulty with it please contact Ubitech as listed above for a quick and efficient solution to the
problem.
FCC STATEMENT: This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation. This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate the receiving
antenna; increase the separation between the equipment and the receiver; connect the
equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the user's authority
to operate the equipment. Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
IC STATEMENT: This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Contact us if you have any questions
https://www.facebook.com/
g roups/283898176125297
http://www.ubitech.hk
Facebook®
Facebook®