Ultra Start 3250 SERIES User manual

Advanced 2-Way
Remote Vehicle Starter
AUTOMATIC AND MANUAL
TRANSMISSION MODELS
OWNERS GUIDE
FCC/ID Notice
This device complies with Part 15 of the FCC rules. Operation is
subject to the following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the
part responsible for compliance void the user’s authority to operate this
devise.
TECH SUPPORT
Western Canada 1 800 279-0636
United States: 1 866 698-5872
Eastern Canada Bilingual: 1 800 268-0683
E-Mail Tech Support: [email protected]
Check Our Web Site: www.ultrastarters.com
WWW.ULTRASTARTERS.COM
See website for a full size printable version of this manual.
3250
3250M
3250
3250M
3 Year Warranty Available on Certain Products - See Dealer For Details.
The manufacturer warrants to the original purchaser of their remote starters and alarms, that the product
shall be free from defects in material and workmanship. However, should this product be proven to be
defective,withinatwoyearperiodfromtheoriginaldateofpurchase,themanufacturer will,withoutcharge
tothepurchaser(excludinganycharges incurred to have theproductdeliveredtothemanufacturer),repair
or replace any part of the remote starter and/or alarm which the manufacturer agrees to be defective. All
warranties apply on to the original purchaser and the vehicle in which it is originally installed. Repairs or
replacement of defective modules shall remain at the discretion of the manufacturer. All other parts,
components, accessories and/or optional equipment pertaining to the remote starter and alarm are not
includedinthe manufacturer’s warranty.Thiswarrantyis non-transferable.Requestforwarrantyservice
from any FactoryAuthorized Dealer must be accompanied with the original purchase receipt or have
product registered by authorized dealer on manufacturer’s website. Failure to comply with any of
theseconditionsmayresultinwarrantybeingvoided.
This warranty does not cover the following: removal and reinstall labour charges, shipping charges, abuse,
misuse, or accidental damages to the remote starter and alarm, automobile, and/or parts there of. This
warrantyis void upon modification, repairs, oralterations of any part of the System.Themanufacturerdoes
notguaranteeor insure against theft of the vehicle or its contents.Alarmmodelsaredesignedonlytoactas
a deterrent against possible theft. This alarm may qualify for auto insurance discounts, contact your
Insurance Agent for further information . The manufacturer shall not be held liable for any consequential
damages due to breach of this or any other warranty, expressed, or implied. This warranty gives you
specificlegalrights.Yourspecificlegalrightsmayvaryforeachregion.
CERTAIN DAMAGES EXCLUDED - The manufacturer expressly disclaims any liability or responsibility
for incidental damages caused by the product, including economic loss, loss of use of the product, car
rentals, or any other costs relating to the care and custody of the product. The manufacturer disclaims
liability or responsibility for any consequential damages caused by the product or resulting from its use,
including the cost of repairing or replacing other property damaged by the product or caused by its use,
whether or not the product is working properly. The product is intended to deter unauthorized use of the
vehiclesinwhichit isinstalled. Themanufacturerdoesnotwarrant thattheproductisfool-safe against theft
and/or vandalism and/or human error or misuse. The manufacturer accepts no liability or responsibility for
any damage of any kind whatsoever caused to any vehicle in which the product is installed or any resulting
damagefrom its use. The manufacturer acceptsno responsibility or liability for any damageresulting to or
theft of the vehicle or its contents, caused or alleged to be caused, directly or indirectly, by failure of the
product.
WARRANTY
If the Key Icon in the remote’s program menu is flashing, the remote starter has been
disabled. This can be because of various inputs including hood open, brake active,
tach lockout or system in valet mode.
When the remote start button is pressed in this mode, the remote will respond by
giving 3 beeps and flashing the Key Icon in the program window. The Key Icon on the
top of the display will not be illuminated.
The vehicle’s start fault condition must be corrected in order to remote start.
Start Fault Indicator
Owner’s Guide

1. Press and hold buttons #2 & #3 together for two seconds.
2. Thesystemwillflash theparklightsandhonkthehorn(optional)fivetimes.
3. Theremotewillbeep anddisplaythesystemscurrentstatus.
1. Press and hold the Trunk Release Button ( Button #2) for three seconds.
2. The doors will unlock and the trunk release will then activate. The Trunk Release will then be
confirmed by 2 park light flashes.
3. The remote will beep once then beep twice to confirm the Trunk Release was activated. The Trunk
Release Icon will appear at the top of the LCD screen for five seconds.
4. For safety reasons, the Trunk Release output will be disabled and will not activate when the ignition
key is in the on position.
1. Press and release button #1 on the remote transmitter.
2. The park lights will flash and the horn (optional) will honk one time.
3. The remote will beep once to confirm.
4. The doors will lock.
5. The LOCK icon will appear on the LCD display of the remote.
4. The LED’s on the antenna will start flashing within five seconds.
1. Press and release button #1 on the remote transmitter.
2. The park lights will flash 2 times and the horn (optional) will honk 2 times.
3. The remote will beep twice to confirm.
4. The doors will unlock.
5. The UNLOCK icon will appear on the LCD display of the remote
4. The LED’s on the antenna will stop flashing within five seconds.
Lock Doors
Unlock Doors
Trunk Release
Car Finder Mode
ACTIVATE PANIC MODE
1. Press and hold Button #1 for three seconds.
2. The park light will begin to flash and the horn will start to honk.
PANIC MODE DISABLE
- Press and release Button #1 to disable Panic Mode and lock the doors.
- Press and release Button #1 to disable Panic Mode and unlock the doors.
Note : Panic Mode will stay activated until disable by the remote transmitter.
Panic Mode
1. Press and release Button #3 on the remote transmitter.
2. The Park lights will flash and the horn(optional) will honk one time.
3. The remote will beep 3 times and the key icon will begin flashing on the top of the LCD screen.
4. When the vehicle has started, the system will flash the park lights four times then remain “On” while
the vehicle is running. (Normally 15minutes)
5. The Runtime Bar Graph will appear on the LCD screen and begin counting down.
6. The vehicle will continue to run for the programmed runtime. (Normally 15 minutes).
Remote Start
Extended Run Time
Remote Stop
Idle Mode
1. Press and hold Button #3 for three seconds. The remote starter will shut down.
2. The park lights will flash two times and the horn(optional) will honk two times.
Note: Pressing the brake pedal or opening hood will also stop the vehicle.
1. Press and release Button #1 while the vehicle is running by the ignition key..
2. The park lights will turn on and the horn(optional) will honk once.
3. The Remote will beep and the Run Time Bar Graph will light up.
4. Turn the ignition key “off” and the vehicle will continue to run.
5. Exit the vehicle and leave it running safely without the keys in the ignition.
Note: Always lock the doors when leaving the vehicle unattended.
1. Press and release Button #3 while the vehicle is running under the remote starter.
2. The park lights will flash and the horn (optional) will honk to confirm the runtime has been extended.
The system will reset the runtime (normally 15 minutes).
Note: The Runtime Bar Graph is not updated by the activation of the Extended Runtime.
Reservation Mode (Manual Transmissions Only)
TO INSURE SAFE STARTING OF MANUAL TRANSMISSION VEHICLES
1. While the vehicle is running, apply the Park Brake then press & release the Brake Pedal.
2. The park lights will flash to confirm that reservation mode has been activated.
3. Remove the key from ignition (The vehicle will continue to run) exit the vehicle and close the door.
4. The vehicle will shut off when the door is closed. (If the vehicle has a delay dome-light, it may continue
to run until the dome-light turns off)
5. The system is now in Reservation Mode and can be safely Remote Started.
Note: Opening the door after this point will cancel the Reservation Mode*.
*To re-enter the vehicle without cancelling the Reservation Mode. Remote Start the vehicle and unlock
the door’s by the remote, (The unlock icon will appear) then open the door. When done, close the door
and press Button #1 on the remote (the system will arm) then press and hold button #3 for three seconds
(The vehicle will turn Off).
Owner’s Guide
Owner’s Guide

LCD DISPLAY
TELEPHONE ICON
When the vehicle starts in timer mode, this icon will appear in conjunction with the usual
icons that indicate that the vehicle is running by the remote starter.
Note: When the vehicle starts in timer mode no sound should come from the remote
and the back light should not turn on.
KEY ICON
This icon will begin to flash when the remote starter button is first pressed.After the vehicle
has started this icon will stay on solid. The wheels on the car will begin to rotate.
SIREN ICON - Alarm Models Only
This icon indicates that the alarm has been triggered. The remote will start to beep and the
siren icon will come on solid at the same time as the icon for the violated zone. The remote
will stop beeping after one minute. Both icons will continue to flash until the system is
disarmed.
ANTENNA ICON
This icon will be visible on the LCD whenever the remote is within transmitting range of the
vehicle. The icon will disappear when the remote leaves that transmitting range.
STATUS ICONS
These icons are located at the top of the LCD screen as scene above. These icons are used to display the
current operating status of the system. Some icons will always be visible and other will only be displayed
when one of the systems features are in use. The following is a list and description of the status icons and
when they will be present on the LCD screen
STATUS CHECK MODE
This feature is used to check the status of the alarm system or the remote starter.
1. To check the status press and release Button #4 on the remote transmitter.
2. The remote will display the icons of the active features on the LCD screen.
Note: In status check mode the LCD will stay on for five seconds then shut off.
STATUS ICONS
PROGRAM ICONS
PROGRAM ICONS
TRUNK ICON
This icon will be displayed on the LCD screen when the trunk release output is activated by
the remote transmitter. This icon will be displayed on the screen until the system is armed
or if the status button is pressed
BATTERY ICON
This icon is always present when the LCD screen active. This icon will indicate the current
battery level for the remote transmitter. The black area of the icon will disappear as the
battery level decreases.
RUN TIMER
This icon activates during remote starting. The bar graph will count down in 2 minute
increments, indicating how much time is left on the vehicles remote start sequence. Note: If
run time is set to more than 15 minutes graph will remain full time until remaining
runtime is less than 14 minutes.
PROGRAM ICON
This icon will be displayed on the LCD screen until the user program mode is accessed.
While in user program mode the letter “P” from the icon will disappear. The letter will re-
appear when user Program Mode is exited.
TELEPHONE ICON (Timer Mode)
When this icon is displayed in the left program column if confirms that the Cold
Temperature Mode or Timer Mode has been programmed ON.
SHOCK SENSOR ICON - Alarm Models Only
This icon indicates the status of the shock sensor delete feature. Shock sensor delete
allows the user to deactivate the shock sensor. If the icon is present on the LCD screen
the shock sensor is active. If the icon is not present on the LCD screen the shock sensor
delete feature has been activated and the sensor will be deactivated until programmed
on..
KEY ICON
This icon indicates the status of the remote starter. When Key is ON, remote starter will
not activate. See diagnostics
**This Icon is not used in Transmitter Program Mode.
HORN ICON(Chirp Delete)
This icon indicates the status of the chirp delete feature. If the icon is on, the horn will
work normally. If the icon is not displayed on the LCD the chirps delete feature is on and
the horn will not chirp.
Note: Chirp delete disables the Lock and Unlock chirps Only.
SERVICE MODE ICON
This icon indicates the status of the Service Mode feature. If the question mark icon is
present the system is in Service Mode (Valet Mode).
Note: While in service Mode, only the keyless entry features of the system will still
operate.
NUMBER ICON(Dual Car Operation)
This icon indicates the status of the Dual Car Operation mode. When the icon is off the
remote will operate car one. When the icon is on the remote will operate car two.
*This icon is not used in transmitter Program Mode.
#
?
USER PROGRAM MODE
User Program Mode allows the user to program system features from the remote transmitter.
The following icons will be displayed on the LCD screen to determine the
status of the feature.
To Enter User Program Mode
1. Press and hold button #4 for three seconds. The remote will respond with two beeps.
2. The system is now in User Program Mode. The telephone icon will begin to flash.
3. Press button #1 to scroll the list of features. Selected feature icon will begin to flash.
Press button #2 to turn the feature icon Off.
Press button #3 to turn the feature icon On.
4. Press button 4 to exit program mode and save settings.
Note: If the remote is not used for 20 seconds the system will exit Program Mode.
Owner’s Guide
Owner’s Guide

Emergency Service Mode - (Valet)
This feature will disable the system except for locking and unlock functions.
Thismodecanalso used ifaremoteislost,damagedorif thesystemmalfunctions.
ENTERINGSERVICEMODE
1. While the ignition is “On” press and hold the Program button on the antenna for 5 seconds or until the horn
(optional) honks5times.
EXITINGSERVICE MODE
1. While the ignition is “On” press and hold the Program button for 5 seconds or until the horn (optional) honks 2
times.
Note:Remotestarterfunctions willbedisabled andtheLED willbe“on”steady.
Thedoorlocksand the trunkreleasewill still beoperational.
Ignition
“On”
7 sec.
ATTENTION: THE SYSTEM MUST BE PLACED INTO SERVICE MODE BEFORE ANY UNDER HOOD SERVICING IS DONE TO
THE VEHICLE. IT IS THE RESPONSIBILITY OF THE VEHICLE’S OWNER TO INSURE THAT THIS IS DONE. THE
MANUFACTURERACCEPTSNORESPONSIBILITY FORACCIDENTALSTARTINGWHILEVEHICLEIS BEINGSERVICED.
Battery Replacement
1
Lift
Slide
+
-
Transmitter Operation
1
23
4
Press Once to Lock Doors and arm the alarm (if equipped)
Press 2nd Time & Hold for Constant Lock Output
Press and hold for 3 seconds to activate Panic Mode
Press Once to disable Panic Mode
Press Once for Unlock doors and Disarm Alarm (if equipped)
Press & Hold for Trunk / Aux Output
Press Once for Start - (2 Times if programmed for Safety Start)
Press & Hold for 3 seconds while running to turn off
While running with the key, press the button to activate Idle Mode
Hold for 3 seconds to enter User Programmable Features
Press and release button 4 then press and hold button 3 for three seconds
to activate the Timer Mode
Press both buttons for 3 seconds to activate Car Finder Mode
1
2
2&3
3
4
PARK LIGHTS STATUS LED DIAGNOSTIC CODE
3 Flashes Series of 3 Flashes Door Opened “M” Models
3 Slow Flashes No Flashes StartAttempt In Service Mode
4 Slow Flashes Series of 4 Flashes Not in Reservation Mode “M” units
5 Flashes Series of 5 Flashes Hood Pin Grounded (Open)
6 Flashes Series of 6 Flashes Brake Pedal Shutdown
7 Flashes Series of 7 Flashes Tach Lock-Out
8 Flashes Series of 8 Flashes 3 StartAttempts with no start
DIAGNOSTICS
System Service Mode - By Remote
ACTIVATE Service Mode (User Programmable Feature)
1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the ?starts flashing on the LCD screen.
3 - Press button #3 and the ? symbol will come on solid.
4 - Press button #4 to exit User Program Mode.(System Is Now In Service Mode)
DEACTIVATE Service Mode
1 - Press and hold button #4 for 3 seconds. (The remote will beep twice)
2 - Press button #1 Five times or until the ?starts flashing on the LCD screen.
3 - Press button #2 and the ? symbol will turn off.
4 - Press button #4 to exit User Program Mode.(Serice Mode is Deactivated)
The battery icon on the remote will indicate the present level of the transmitter battery. When the
transmitter indicates the battery is low it should be replaced. Replace with quality 1.5volt “AAA” battery.
Timer Mode
1.Press & release button #4, then press and hold button #3 for 5 seconds, the lights will turn “On”.
2. Whilethe parkinglightsare “on”thestartcycle canbeselected.
1 hour cycle Press button #1 1 Park light flash
2 hour cycle Press button #2 2 Park light flashes
3 hour cycle Press button #3 3 Park light flashes
4 hour cycle Press button #4 4 Park light flashes
3. The system will start vehicle at selected start cycle for a period up to 24 hours.
Owner’s Guide
Owner’s Guide