UltraLink Products ULM300USB User manual

Quick Start Guide
ULTRALINK ULM300USB
High-Performance 2.4 GHz Digital Wireless
System with Handheld Microphone and
Dual-Mode USB Receiver
A54-00001-48685

ULTRALINK ULM300USB
Hook-Up
XENYX QX2442USB
Laptop
B115MP3

ULTRALINK ULM300USB Controls
Type of product: Wireless Microphone
ULM300USB Controls
1. USB connector
2. POWER/STATUS LED
3. VOLUME UP Button (—Power on/-Volume up/-Unmute)
4. VOLUME DOWN Button (-Volume down/—Mute/
—Power o from Mute)
NOTE:“—” (long dash) = long press; “-” (hyphen) = short press.
LED Status Key
The following table describes LED behavior on both the microphone and
the USB wireless receiver:
Activity LED Color LED Behavior
No Signal Amber Flashes on/o slowly
Connected, Active Green Solid
Connected, Muted Green Flashes on/o quickly
Connected, Active,
Low Battery Green/Red Alternating colors
Connected, Muted,
Low Battery Green/Red Alternating colors,  a s h e s o n / o 
ULM300USB Getting Started
1. Plug the USB wireless receiver to the designated USB socket on
wireless-enabled BEHRINGER mixers, powered speakers or other
compatible products, or to a USB port on a computer. The POWER/
STATUS LED on the receiver will slowly ash amber.
2. Press and hold the VOLUME UP button on the wireless microphone
to switch it on and commence transmission. Both the LEDs on the
wireless microphone and USB wireless receiver will light solid green
once connected.
3. Once switched on, the wireless microphone will be set at its previous
operating volume level. Use the VOLUME UP and VOLUME DOWN
buttons to adjust the volume.
4. A long press of the VOLUME DOWN button will put the wireless
microphone into mute. The mute condition is indicated by rapid
green ashing of the LED. If the user does not unmute within
10 minutes, the wireless microphone will power down to save
battery life.
5. A further long press of the VOLUME DOWN button when in mute will
switch o the wireless microphone.
6. A short press of the VOLUME UP button will unmute the wireless
microphone. When the wireless microphone is unmuted, it will
return to the previous volume level.
(2)
(3)
(4)
(2) (1)
Model: ULM300D
Model: ULM300M

ULM300USB Controles
Tipo de producto: Micrófono inalámbrico
Controles del ULM300USB
1. Conector USB
2. Piloto POWER/STATUS
3. Botón VOLUME UP (—Encendido/-Subir volumen/-Reactivar)
4. Botón VOLUME DOWN (-Bajar volumen/—Anulación (mute)/
—Apagado desde mute)
NOTA:“—” (guión largo) = pulsación prolongada;
“-” (guión) = pulsación breve.
Clave de estado del piloto
La tabla siguiente describe el comportamiento del piloto tanto en el
micrófono como en el receptor inalámbrico USB:
Actividad Color del piloto Comportamientodelpiloto
Sin señal Naranja Parpadeo lento
Conectado, activo Verde Iluminado jo
Conectado,
anulado (mute) Verde Parpadeo rápido
Conectado, activo,
batería casi descargada Verde/rojo Colores alternando
Conectado, anulado
(mute), batería casi
descargada
Verde/rojo Colores alternando,
parpadeo
ULM300USB Primeros pasos
1. Conecte el receptor inalámbrico USB en la toma USB especicada de
las mesas de mezclas, altavoces autoamplicados u otros productos
compatibles y con capacidad inalámbrica BEHRINGER o en un
puerto USB de un ordenador. El piloto POWER/STATUS del receptor
comenzará a parpadear lentamente en color naranja.
2. Mantenga pulsado el botón VOLUME UP del micrófono inalámbrico
para encenderlo y que comience la transmisión. Tanto el piloto
del micrófono inalámbrico como el del receptor inalámbrico USB
se quedarán iluminados jos en color verde una vez que ambas
unidades estén conectadas.
3. Una vez encendido, el micrófono inalámbrico se ajustará al último
nivel de volumen jado. Use los botones VOLUME UP y VOLUME
DOWN para modicar ese nivel de volumen.
4. Una pulsación prolongada del botón VOLUME DOWN hará que el
micrófono inalámbrico quede anulado (mute). Esta condición será
indicada por un rápido parpadeo del piloto en color verde. Si el
usuario no reactiva el micro en los 10 minutos siguientes, el micro se
apagará automáticamente para ahorrar batería.
5. Una pulsación más larga del botón VOLUME DOWN mientras está
desactivado (mute) hará que el micrófono inalámbrico se
apague totalmente.
6. Una pulsación breve del botón VOLUME UP hará que el micro se
reactive. Cuando el micrófono inalámbrico sea reactivado volverá al
nivel de volumen elegido previamente.
(2)
(3)
(4)
(2) (1)
Model: ULM300D
Model: ULM300M

ULM300USB Réglages
Type de produit : micro sans l
ULM300USB Réglages
1. Connecteur USB
2. LED POWER/STATUS
3. Bouton VOLUME UP (— Mise sous tension/- Monter le volume/
- Quitter le mode Mute)
4. Bouton VOLUME DOWN (- Baisser le volume/—Mode Mute/
— Mise hors tension à partir du mode Mute)
Remarque : “—” = pression longue ; “-” = pression courte.
LED Status
Le tableau ci-dessous décrit les diérents états de la LED du micro et du
récepteur USB sans l:
Activité Couleurde laLED État de la LED
Pas de signal Orange Clignote lentement
Connecté, actif Vert Allumée en continu
Connecté, mode Mute Vert Clignote rapidement
Connecté, actif,
batterie faible Vert/rouge Alterne diérentes couleurs
Connecté, mode Mute,
batterie faible Vert/rouge Alterne diérentes couleurs, clignote
ULM300USB Mise en œuvre
1. Connectez le récepteur USB sans l au port USB correspondant
sur une console de mixage, enceinte active ou tout autre produit
BEHRINGER compatible avec les micros sans l, ou encore au port
USB d'un ordinateur. La LED POWER/STATUS du récepteur clignote
lentement en orange.
2. Maintenez le bouton VOLUME UP du micro enfoncé an de le mettre
sous tension et de démarrer la transmission. La LED du micro et celle
du récepteur USB restent allumées en vert lorsque la connexion
est établie.
3. Lorsque le micro est activé, son volume est au niveau réglé lors de la
précédente utilisation. Utilisez les boutons VOLUME UP et VOLUME
DOWN pour régler le volume.
4. Maintenez le bouton VOLUME DOWN enfoncé pour placer le micro
en mode Mute. Lorsque la fonction Mute est activée, la LED clignote
rapidement en vert. Si le mode Mute n'est pas désactivé au bout de
10 minutes, le micro sans l est placé automatiquement hors tension
pour économiser la batterie.
5. Une pression longue sur le bouton VOLUME DOWN lorsque le micro
est en mode Mute permet de le mettre hors tension.
6. Une pression sur le bouton VOLUME UP permet de désactiver le
mode Mute. Lorsque le mode Mute est désactivé, le volume du micro
revient au dernier niveau réglé.
(2)
(3)
(4)
(2) (1)
Model: ULM300D
Model: ULM300M

ULM300USB Bedienelemente
Produkttyp: Drahtlosmikrofon
ULM300USB Bedienelemente
1. USB-Anschluss
2. POWER/STATUS-LED
3. VOLUME PLUS-Taste (—Einschalten/-Volume plus/
-Stummschaltung aus)
4. VOLUME MINUS-Taste (-Volume minus/—Stummschaltung/
—Ausschalten nach Stummschaltung)
HINWEIS: “—” (langer Strich) = lange drücken;
“-” (kurzer Strich) = kurz drücken.
LED Status-Legende
Die folgende Tabelle beschreibt das Verhalten der LED am Mikrofon und
am USB-Drahtlosempfänger:
Aktivität LED-Farbe LED-Verhalten
kein Signal gelb blinkt langsam ein/aus
verbunden, aktiv grün leuchtet
verbunden, stumm grün blinkt schnell ein/aus
verbunden, aktiv,
Batterie schwach grün/rot wechselnde Farben
verbunden, stumm,
Batterie schwach grün/rot wechselnde Farben, blinkt ein/aus
ULM300USB Erste Schritte
1. Schließen Sie den USB-Drahtlosempfänger an den für den
Drahtlosempfang vorgesehenen USB-Port von BEHRINGER Mixern,
Aktivlautsprechern und anderen kompatiblen Produkten oder an
den USB-Port eines Computers an. Die POWER/STATUS-LED des
Empfängers blinkt langsam gelb.
2. Halten Sie die VOLUME PLUS-Taste des Drahtlosmikrofons gedrückt,
um es einzuschalten und die Übertragung zu starten. Sobald die
Verbindung hergestellt ist, leuchten die LEDs des Drahtlosmikrofons
und USB-Drahtlosempfängers konstant grün.
3. Nach dem Einschalten ist das Drahtlosmikrofon auf seine vorherige
Betriebslautstärke eingestellt. Sie können den Pegel mit den
VOLUME PLUS- und VOLUME MINUS-Tasten ändern.
4. Halten Sie die VOLUME MINUS-Taste gedrückt, um das
Drahtlosmikrofon stummzuschalten. Die Stummschaltung wird
durch schnelles grünes Blinken der LED angezeigt. Wenn die
Stummschaltung nicht innerhalb von 10 Minuten aufgehoben wird,
schaltet sich das Drahtlosmikrofon aus, um die Batterien zu schonen.
5. Halten Sie die VOLUME MINUS-Taste nochmals gedrückt, um das
stummgeschaltete Mikrofon auszuschalten.
6. Ein kurzer Druck auf die VOLUME PLUS-Taste hebt die
Stummschaltung des Drahtlosmikrofons wieder auf. Danach ist das
Drahtlosmikrofon wieder auf seine vorherige Lautstärke eingestellt.
(2)
(3)
(4)
(2) (1)
Model: ULM300D
Model: ULM300M

ULM300USB Controles
Tipo do produto: Microfone sem o
Controles ULM300USB
1. Conector USB
2. LED POWER/STATUS
3. Botão VOLUME UP (—Power on/-Volume up/-Unmute)
4. Botão VOLUME DOWN (-Volume down/—Mute/
—Power o from Mute)
NOTA: “—” (traço longo) = pressionar demoradamente;
“-” (hífen) = pressionar rapidamente.
Chave de Status de LED
A tabela a seguir descreve o comportamento do LED no receptor do USB
sem o e microfone:
Atividade Cor do LED Comportamento do LED
Sem sinal Âmbar Pisca on/o
vagarosamente
Conectado, Ativo Verde Sólido
Conectado,
em modo Mute Verde Pisca on/o rapidamente
Conectado, Ativo
Bateria baixa
Verde/
Vermelho Cores alternadas
Conectado, em modo
Mute, Bateria baixa
Verde/
Vermelho
Cores alternadas,
pisca on/o
ULM300USB Primeiros Passos
1. Conecte o receptor USB sem o à soquete USB designada em
misturadores BEHRINGER habilitados para uso wireless, alto-falantes
amplicados ou outros produtos compatíveis, ou a uma porta
USB no seu computador. O LED POWER/STATUS no receptor piscará
vagarosamente em cor âmbar.
2. Aperte e segure o botão VOLUME UP no microfone sem o para
ligá-lo e iniciar a transmissão. Ambos os LEDs no receptor USB sem
o e microfone sem o acenderão uma luz verde sólida quando
estiverem conectados.
3. Quando ligado, o microfone sem o estará ajustado ao seu nível de
volume operacional anterior. Use os botões VOLUME UP e
VOLUME DOWN para ajustar o volume.
4. Apertar o botão VOLUME DOWN demoradamente coloca o microfone
sem o em modo mute. A condição mute é indicada por uma luz
verde do LED que pisca rapidamente. Se o usuário não o tirar do
modo mute em 10 minutos, o microfone sem o será colocado em
modo de espera para economizar bateria.
5. Um outro aperto demorado no botão VOLUME DOWN enquanto em
modo mute desligará o microfone sem o. 
6. Um aperto rápido do botão VOLUME UP retirará o microfone sem
o do modo mute. Quando o microfone sem o é retirado do modo
mute, ele volta ao nível de volume anterior. 
(2)
(3)
(4)
(2) (1)
Model: ULM300D
Model: ULM300M

Specication
RF output < 10 dBm (10 mW)
Operating range 60 m (200 ft)*
Dynamic range 93 dB, A-weighted**
Equivalent input noise -120 dBu
Frequency response 10 Hz – 20 kHz, ±1 dB**
(wireless link)
Sampling rate 48 kHz
Resolution 24-bit
Encoding 4-bit ADPCM (192 kbps)
Latency 14.3 ms
RF frequency 2.4 GHz ISM band
(2.404~2.468 GHz,
17 channels)
USB current consumption 70 mA @ 5 VDC
Battery type 2 x AA (LR6)
Alkaline cells
Battery life > 24 hrs
Dimensions (H x W x D)
Microphone 260 x 53 x 53 mm
(10.2 x 2.1 x 2.1")
Wireless receiver 8.5 x 76 x 22 mm
(0.3 x 3.0 x 0.9")
Weight
Microphone 0.3 kg (0.7 lbs)
Wireless receiver 0.01 kg (0.02 lbs)
*Achievable range will be dependent on nearby sources of RF interference and/or
line of sight obstacles.
**Measured from analog input to analog output at maximum level.

LEGAL DISCLAIMER
MUSIC Group accepts no liability for any loss which may be
suered by any person who relies either wholly or in part upon
any description, photograph, or statement contained herein.
Technical specications, appearances and other information are
subject to change without notice. All trademarks are the property
of their respective owners. MIDAS, KLARK TEKNIK, LAB GRUPPEN,
LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON,
BEHRINGER, BUGERA and DDA are trademarks or registered
trademarks of MUSIC Group IP Ltd. © MUSIC Group IP Ltd. 2016
All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions
and additional information regarding MUSIC Group’s
Limited Warranty, please see complete details online at
music-group.com/warranty.
NEGACIÓN LEGAL
MUSIC Group no admite ningún tipo de responsabilidad por
cualquier daño o pérdida que pudiera sufrir cualquier persona
por conar total o parcialmente en la descripciones, fotografías o
armaciones contenidas en este documento. Las especicaciones
técnicas, imágenes y otras informaciones contenidas en este
documento están sujetas a modicaciones sin previo aviso.
Todas las marcas comerciales que aparecen aquí son propiedad
de sus respectivos dueños. MIDAS, KLARK TEKNIK, LAB GRUPPEN,
LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON,
BEHRINGER, BUGERA y DDA son marcas comerciales o marcas
registradas de MUSIC Group IP Ltd. © MUSIC Group IP Ltd.
2016 Reservados todos los derechos.
GARANTÍA LIMITADA
Si quiere conocer los detalles y condiciones aplicables de la
garantía así como información adicional sobre la Garantía
limitada de MUSIC Group, consulte online toda la información
en la web music-group.com/warranty.
DÉNI LÉGAL
MUSIC Group ne peut être tenu pour responsable pour toute
perte pouvant être subie par toute personne se ant en partie
ou en totalité à toute description, photographie ou armation
contenue dans ce document. Les caractéristiques, l’apparence
et d’autres informations peuvent faire l’objet de modications
sans notication. Toutes les marques appartiennent à leurs
propriétaires respectifs. MIDAS, KLARK TEKNIK, LAB GRUPPEN,
LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON,
BEHRINGER, BUGERA et DDA sont des marques ou marques
déposées de MUSIC Group IP Ltd. © MUSIC Group IP Ltd.
2016 Tous droits réservés.
GARANTIE LIMITÉE
Pour connaître les termes et conditions de garantie applicables,
ainsi que les informations supplémentaires et détaillées sur
la Garantie Limitée de MUSIC Group, consultez le site Internet
music-group.com/warranty.

HAFTUNGSAUSSCHLUSS
MUSIC Group übernimmt keine Haftung für Verluste,
die Personen entstanden sind, die sich ganz oder teilweise
auf hier enthaltene Beschreibungen, Fotos oder Aussagen
verlassen haben. Technische Daten, Erscheinungsbild und
andere Informationen können ohne vorherige Ankündigung
geändert werden. Alle Warenzeichen sind Eigentum der
jeweiligen Inhaber. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE,
TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER,
BUGERA und DDA sind Warenzeichen oder eingetragene
Warenzeichen der MUSIC Group IP Ltd. © MUSIC Group IP Ltd.
2016 Alle Rechte vorbehalten.
BESCHRÄNKTE GARANTIE
Die geltenden Garantiebedingungen und zusätzliche
Informationen bezüglich der von MUSIC Group
gewährten beschränkten Garantie nden Sie online unter
music-group.com/warranty.
LEGAL RENUNCIANTE
O MUSIC Group não se responsabiliza por perda alguma que
possa ser sofrida por qualquer pessoa que dependa, seja de
maneira completa ou parcial, de qualquer descrição, fotograa,
ou declaração aqui contidas. Dados técnicos, aparências e
outras informações estão sujeitas a modicações sem aviso
prévio. Todas as marcas são propriedade de seus respectivos
donos. MIDAS, KLARK TEKNIK, LAB GRUPPEN, LAKE, TANNOY,
TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA
e DDA são marcas ou marcas registradas do MUSIC Group IP Ltd.
© MUSIC Group IP Ltd. 2016 Todos direitos reservados.
GARANTIA LIMITADA
Para obter os termos de garantia aplicáveis e condições e
informações adicionais a respeito da garantia limitada do
MUSIC Group, favor vericar detalhes na íntegra através do
website music-group.com/warranty.

FEDERAL COMMUNICATIONS
COMMISSION COMPLIANCE
INFORMATION
Responsible Party Name: MUSIC Group Services
NV Inc.
Address: 5270 Procyon Street
Las Vegas, NV 89118
USA
Phone Number: [phone]
ULM300D
complies with the FCC rules as mentioned in the
followingparagraph:
This equipment has been tested and found to comply with
the limits for a ClassB digital device, pursuant to part
15 of the FCC Rules. Theselimits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. Ifthis equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the
followingmeasures:
•
• Reorient or relocate the receiving antenna
•
• Increase the separation between the equipment
andreceiver
•
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected
•
• Consult the dealer or an experienced radio/TV technician
forhelp
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
includinginterference that may cause undesiredoperation.
This device complies with FCC radiation exposure limits set
forth for an uncontrolled environment.
Important information:
Changes or modications to the equipment not expressly
approved by MUSIC Group can void the user’s authority to use
the equipment.
Operation in the 2.4 GHz ISM (Industrial, Scientic, Medical)
frequencyband may be subject to interference from other
transmitting equipment operating in this band. Inthe
event of such interference, please verify and reassign
the transmitting channels of any potentially interfering
transmittingequipment.
ULM300D

Dedicate Your Life to Music