UltraLite DIFFUSION 200 DYNAMIC WHITE User manual

Artikel Nr. ULF200DW (Asymmetric)
USER MANUAL
Version 1.0
Be sure to read the USER MANUAL carefully before using this product.
Be sure to keep the USER MANUAL properly for future needs.
Use this product correctly when you can fully understand the User Manual
DIFFUSION
200 DYNAMIC WHITE

The manufacturer will not accept liability for any resulting damages caused by the non-observance of this
manual or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to warranty.
During the operation the housing becomes hot). Allow the fixture to cool approximately 20 minutes prior to
manipulate with it.
Make sure that the available voltage is not higher than stated on the rear panel.
WARNING! This unit does not contain an ON/OFF switch. Always disconnect power input cable to
completely remove power from unit when not in use or before cleaning or servicing the fixture.
Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the
power-cord from time to time.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only handle the
power-cord by the plug. Never pull out the plug by tugging the power cord.
This device falls under protection class I. Therefore it is essential to connect the yellow/green conductor to
earth.
The electric connection, repairs and servicing must be carried out by a qualified employee.
Do not connect this device to a dimmer pack.
Do not switch the fixture on and off in short intervals as this would reduce the lamp’s life.
During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
Do not touch the device’s housing bare hands during its operation (housing becomes hot)!
For replacement use lamps and fuses of same type and rating only.
Thank you for choosing our Diffusion 200 Dynamic White . for your own safety , please read this user manual
carefully
BEFORE YOU INITIAL START - UP!
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to
ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warning
notes written in this manual.
Important:
CAUTION!
Be careful with your operations.
With a high voltage you can suffera dangerous electric shock when touching the wires!
1.Safety instructions
CAUTION!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
CAUTION ! EYE DAMAGES !
Avoid looking directly into the light source
(meant especially for epileptics) !
DIFFUSION DYNAMIC WHITE
01

DIFFUSION DYNAMIC WHITE
▲ DIFFUSION
2.UNPACKING
▲ Power Connector
▲ User Manual*1
The DIFFUSION adopts 200W LED lamp which features high brightness and
stability. Please carefully unpack it when you receive the fixture and check whether it is damaged during
the transportation. And please check whether the following items are included inside the box:
The DIFFUSION is made of a new type of high temperature strength
and cast aluminum casing with nice outlook . The fixture is designed and manufactured strictly following
CE standards, complying with international standard DMX512 protocol. It’s available independently
controlled and linkable with each other for operation. And it is applicable for large-scale live per
formances, theater, studio, nightclubs and discos.
This manual covers the important information on installation and applications. Meanwhile, please keep
this manual well for future needs.
02
▲ FILTERFRAME

DIFFUSION DYNAMIC WHITE
3.TECHNICAL INFORMATION
03

DIFFUSION DYNAMIC WHITE
1.5 m
2.0 m
5m
4m
3m
2m
1m
0m
Height
Lux
900
730
520
390
265
138
5 / 8 m
04
4.PHOTOMETRICS DIAGRAM
ŸDiffusion is an asymmetric LED projector.
ŸDo not switch the appliance on if there is a serious temperature difference such as
after transportation
Ÿbecause it could damage the light due to changes in the environment. So be sure to
use the appliance until it is at normal temperature.
ŸThis light should be far from strong shaking during any transport or movement.
ŸDo not expose the appliance to overheating, humidity or the environment with too
much dust during installation. IS do not lay power cables on the floor. Or it may
cause an electronic shock to people. Make sure the installation location is in a safe
condition before installing the equipment.
ŸMake sure to put the safety chain in place and check if the screws are screwed
correctly during device installation.
ŸEnsure that the appliance is operated by qualified personnel who know the
appliance before use.
ŸKeep the original packaging if a second shipment is required.
ŸDo not try to change the projectors without any instruction from the manufacturer or
repair appointed agencies.
ŸIt is not in the warranty interval if there are malfunctions not to follow the user
manual to operate or any illegal operation, such as short circuit, electronic shock,
broken lamp, etc.

DIFFUSION DYNAMIC WHITE
Satety Clamp
6.INSTALLATIONS
Cautions:
For added protection mount the fixtures in areas
outside walking paths, seating areas, or in areas were
the fixture might be reached by unauthorized
personnel.
Before mounting the fixture to any surface, make sure
that the installation area can hold a minimum point
load of 10 times the device’s weight.
Fixture installation must always be secured with a
secondary safety attachment, such as an appropriate
safety cable.
Never stand directly below the device when mounting,
removing, or servicing the fixture.
from a ceiling, or set on a flat level surface (see
illustration below). Be sure this fixture is kept at least
0.5m (1.5 f t) away from any flammable materials
(decoration etc.).
Always use and install the supplied safety cable as a
safety measure to prevent accidental damage and/or
injury in the event the clamp fails.
Mounting points:
Mounting the projector requires extensive experience,
including amongst others calculating working load
limits, a fine knowledge of the installation material
being used, and periodic safety inspection of all
installation material and the fixture. If you lack these
qualifications, do not attempt the installation yourself.
Improper installation can result in bodily injury.
Be sure to complete all rigging and installation
procedures before connecting the main power cord to
the appropriate wall outlet.
Safety Cable
05

DIFFUSION DYNAMIC WHITE
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
MENU ENTER +
-
Produced by ARTHEA LUCE
MADE IN ITALY
TYPE
COLOURS
Diffusion
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
MENU ENTER +
-
Produced by ARTHEA LUCE
MADE IN ITALY
TYPE
COLOURS
Diffusion
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
MENU ENTER +
-
Produced by ARTHEA LUCE
MADE IN ITALY
TYPE
COLOURS
Diffusion
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
MENU ENTER +
-
Produced by ARTHEA LUCE
MADE IN ITALY
TYPE
COLOURS
Diffusion
DIFFUSION 200 - RGBW
DIFFUSION 250 - WW
DIFFUSION 250 - CW
DIFFUSION 200 - DW
The art of light
MADE IN ITALY
LCD DISPLAY
DATE
N°SERIAL
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
POWER DMX
MENU ENTER +
-
ARTHEA LUCE
LED LINE
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
MENU ENTER +
-
Produced by ARTHEA LUCE
MADE IN ITALY
TYPE
COLOURS
Diffusion
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
MENU ENTER +
-
Produced by ARTHEA LUCE
MADE IN ITALY
TYPE
COLOURS
Diffusion
DIFFUSION 200 - RGBW
DIFFUSION 250 - WW
DIFFUSION 250 - CW
DIFFUSION 200 - DW
The art of light
MADE IN ITALY
LCD DISPLAY
DATE
N°SERIAL
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
POWER DMX
MENU ENTER +
-
ARTHEA LUCE
LED LINE
Pin 1= GROUND
Pin 2= DATA -
Pin 3= DATA +
Pin 4 =nc
Pin 5 =nc
Connect the provided XLR cable to the female 5-pin XLR output of your controller and the other side to the
male 5-pin XLR input of the moving head. You can chain multiple projectors together through serial
linking. The cable needed should be two core, screened cable with XLR input and output connectors.
Please refer to the diagram below. DMX-512 connection with DMX terminator.
For installations where the DMX cable has to run a long distance or is in an electrically noisy environment,
such as in a discotheque, it is recommended to use a DMX terminator. This helps in preventing corruption of
the digital control signal by electrical noise. The DMX terminator is simply an XLR plug with a 3 resistor
connected between pins 2 and 3,which is then plugged into the output XLR socket of the last fixture in the
chain. Please see illustrations below.
7.CONTROL CONNECTION
06
DIFFUSION 200 - RGBW
DIFFUSION 250 - WW
DIFFUSION 250 - CW
DIFFUSION 200 - DW
The art of light
MADE IN ITALY
LCD DISPLAY
DATE
N°SERIAL
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
POWER DMX
MENU ENTER +
-
ARTHEA LUCE
LED LINE
DMX
POWER
DIFFUSION 200 - RGBW
DIFFUSION 250 - WW
DIFFUSION 250 - CW
DIFFUSION 200 - DW
The art of light
MADE IN ITALY
LCD DISPLAY
DATE
N°SERIAL
DMX 512
IN OUTmax.12A
AUTOSENSING 90/260Vac 50/60Hz
IN OUT
POWER
PIN1: GND PIN3: n.c.
PIN2: DATA - PIN4: n.c.
PIN3: DATA +
POWER DMX
MENU ENTER +
-
ARTHEA LUCE
LED LINE

LCD DISPLAY
DATE
N°SERIAL
POWER DMX
MENU ENTER +
-
ARTHEA LUCE
LED LINE
DIFFUSION DYNAMIC WHITE
8.MENU OPERATIONS
Dmx Address
BackLigh
Out Lim
A001~AXXX
OFF Signal Mode (On/Off)
Function
DMX address setting
MENU Description
enter
07
Dmx Address
MENU
Dimmer Xeno
Tungsten
it can simulate dimmer effect with
Tungsten or Xenon lamp
Test
White Tmp 2800K to 5800K
Dimmer
Effect
Store
DMX CHAN 1 Chn
5 Chn
1 Channel MODE
5 Channel MODE
Display Reverse
Hold
it allows to turn 180°the reading
of the display.Hold locks the keys.
Press any key for 5" to unlock.
Auto
ON
AUTO allows to turn off the display
after 6 seconds
Out Freq from 1000 to 5000Hz
it allows to set the flickering frequency
from 1000 to 5000 Hz besides the default
value.(NOTE:DMX signal goes ahead this
setting)
Reset
it permits the reset of the unit.Keepin
pressed ENTER and MENU at the
turningon of the unit it allows to
access ALIG features
Sure
Default
it restores all the setting at default
value excepting of led settings and
hour meter.
ID (da 1 a n°)
Remoto
Disables the adjusting of the leds
settingthem at maximum output.
it allow to set the ID number of the
unit by + and - keis (enter)
Measure
MENU
Temp Led
Imput V
Dmx Val
Dmx Rate
Alarms
Out Val
Freq Val
Timers
Soft Ver
Mode
MENU DMX
reset the projector’s dmx operation
0-255
0-255
0-255
0-255

DIFFUSION DYNAMIC WHITE
channel function type of
control effect
1 master dimmer proportional adjust luminous output intensity from 0 to 100% 0 - 255 0% - 100%
select the primary W HITE color 0 - 9 0% - 4%
W HITE 5800 °K 10 - 21 4% - 8%
W HITE 5400 °K 22 - 33 9% - 13%
W HITE 5000 °K 34 - 45 13% - 18%
W HITE 4700 °K 46 - 57 18% - 22%
W HITE 4400 °K 58 - 69 23% - 27%
W HITE 4000 °K 70 - 81 27% - 32%
W HITE 3700 °K 82 - 93 32% - 36%
W HITE 3400 °K 94 - 105 37% - 41%
W HITE 3100 °K 106 - 117 42% - 46%
W HITE 2800 °K 118 - 128 46% - 50%
proportional adjust proportionally white color temperature from 2800°K to
5800°K 129 - 255 51% - 100%
step no effect 0 - 9 0% - 4%
proportional fine dimmer control 16 bit 10 - 255 4% - 100%
step no effect 0 - 9 0% - 4%
proportional variable speed strobing effect, from slow to fast 10 - 57 4% - 22%
step stop strobe 58 - 59 23% - 23%
proportional sequenced pulse effect, slow closing, fast opening
(variable speed pulsing, from slow to fast) 60 - 108 24% - 42%
step stop strobe 109 - 110 43% - 43%
proportional sequenced pulse effect, fast closing, slow opening
(variable speed pulsing, from slow to fast) 111 - 159 44% - 62%
step stop strobe 160 - 161 63% - 63%
proportional random strobe effect with variable speed from slow to fast and
synchronised colour temperature selected 162 - 207 64% - 81%
step stop strobe 208 - 209 82% - 82%
proportional random strobe effect with variable speed from slow to fast and
non-synchronised colour temperature 210 - 255 82% - 100%
white tone
3 dimmer fine
decimal percentage
step
2
4 strobe
600 Hz 0 - 9 0% - 4%
LCD display off 134 - 185 53% - 73%
LCD display on 186 - 199 73% - 78%
led control frequency tuning 1000 Hz 200 - 205 78% - 80%
led control frequency tuning 1500 Hz 206 - 211 81% - 83%
led control frequency tuning 2000 Hz 212 - 217 83% - 85%
led control frequency tuning 2500 Hz 218 - 223 85% - 87%
led control frequency tuning 3000 Hz 224 - 229 88% - 90%
led control frequency tuning 3500 Hz 230 - 235 90% - 92%
led control frequency tuning 4000 Hz 236 - 241 93% - 95%
led control frequency tuning 4500 Hz 242 - 247 95% - 97%
led control frequency tuning 5000 Hz 248 - 255 97% - 100%
park -10 4% 52%133
5 special functions step
-
08

DIFFUSION DYNAMIC WHITE
It is absolutely essential that the fixture is kept clean and that dust, dirt and smoke-fluid residues must not
build up on or within the fixture. Otherwise, the fixture‘s light-output will be significantly reduced. Regular
cleaning will not only ensure the maximum light-output, but will also allow the fixture to function reliably
throughout its life.A soft lint-free cloth moistened with any good glass cleaning fluid is recommended,
under no circumstances should alcohol or solvents be used!
The front objective lens will require weekly cleaning as smoke-fluid tends to building up residues, reducing
the light-output very quickly. The cooling-fans should be cleaned monthly.
The interior of the fixture should be cleaned at least annually using a vacuum-cleaner or an air-jet.
Remove dust and dirt from the fans and cooling vents using a soft brush and vacuum-cleaner. .
10.Maintenance and cleaning
DANGER !
Disconnect from the mains before starting any
maintenance work