UNDERWATER LIGHTS LIMITED UL Ti MATE 130 SA User manual

For sales telephone numbers visit www.underwaterlights.com
underwater lights limited TM
UL Ti MATE RANGE - MODEL- UL Ti MATE 130 SA
DESCRIPTION
This is the most flexible and powerful
“through-hull” submersible marine light for
the large sports fish yachts and is suitable for
GRP-fibreglass and wooden hulls.
The design and development of the
UL Ti MATE 130 SA gave the marine market
their wish with the internal adjustment (SA)
which allows the beam angle to be varied from
a narrow to wide beam and to universally
move the beam direction by 20 degrees from
within the projector housing.
The UL Ti MATE 130 SA has a larger aperture
which increases the light output by 25%.
We advise that the light be installed 250mm
below the minimum waterline.
The boat must be hauled out for installation,
although maintenance of the light is carried
out from inside the hull.
The light is IPX8 to 10 bar.
TECHNICAL SPECIFICATION
Lamp Type - MSD Metal Halide 150w or 250w
Material - Aluminium Bronze and 5083 ALU
Glass Lens - Borosilicate glass
Lamp Life - 3000 Hours - Colour Temp - 7000 K
NOTE
Installation Instruction:
The hole cut-out should be 100 mm.
For Lamp Maintenance allow 170mm behind the projector lid.
Hull thickness range 12 to 120 mm.
Electrical Information:
150w - Recommended maximum distance between ballast and projector 10m.
250w - Recommended maximum distance between ballast and projector 25m.
Cable - 150w-250w High temp. silicone 3 core (Part No S00111, 0.75).
For additional information please visit our web site.
underwater lights limited™
Manufacturers of the Original underwater lights ™
Brand Marine Lighting Products since 1991
UL Ti MATE 130 SA-W1 (250 WATT)
ORDER NUMBER-S00475-SA-V1W1
UL Ti MATE 130 SA-W2 (150 WATT)
ORDER NUMBER-S00475-SA-V2/V3W2
Max hull thickness 120mm
130mm
Hole cut-out 100mm
222mm
Max hull thickness 120mm
130mm
Hole cut-out 100mm
222mm
UL Ti MATE 130 SA
12,000 or 19,000 lumen
Voltage/Amps - 150 watt 120(V3)/230(V2)volt - 1.4 /0.7.A
Voltage/Amps - 250 watt 198/264vac- 1.2A
Light Level - 150w 12,000 Lumens - 250w 19,000 lms

Qualified/Approved personnel must be used to carry out installation
Cut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the
hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screw
the securing ring (18) up “hand tight”. Adjust the screws (19) so the compensating ring is flush to the hull and check the
sealant has flowed completely around the flange. Do “NOT” over tighten the screws as this will squeeze the sealant from
the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbs
Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface
through it, thus protecting the internal core of the hull.
Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mm
After completing the installation procedure it is highly recmmended to coat the exposed body with antifouling.
EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it
bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.
ORDERING NUMBERS
250 WATT LIGHTS - 230V. S00475-SA-V2W1.
150 WATT LIGHTS - 120V. S00475-SA-V3W2. 230V. S00475-SA-V2W2
UL Ti MATE 130 SA INSTALLATION (The UL Ti MATE 130 SA should be no less than 250mm/10” below the water line)
LENS FITTING INSTRUCTIONS
Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets.
Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with an
Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs)
in the sequence shown, check the ring again and re-torque the screws again to the same setting
ELECTRONIC BALLAST COMPLETE
WITH IP65 ENCLOSURE
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO WWW,REGISTER-UWL.COM
FOR TECHNICAL INFORMATION PLEASE EMAIL [e-mail]
SALES, PRODUCT INFORMATION AND NEWS GO TO WWW,UNDERWATERLIGHTS.COM
UL Ti MATE 130 SA -20-8-2012
Recommended Spares Part No
Lamp ( 250w = W 1 ) 91209
Lamp ( 150w = W 2 ) 91210
Glass with gas kets S00281-A
Ballast S00801
TM
OPERATIONAL CONDITIONS AND CONSIDERATIONS
The UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp
replacements.
ELECTRICAL INFORMATION
CABLE SPECIFICATION TO PROJECTOR
150 Watt-250 Watt- High temp silicone three core part number. S00111-0.75-
150 WATT Max distance between ballast and projector with -10 meters.250 WATT Max distance 25 meters
.Ballast power 150 watt ballast 120/230 volt, running current 1.4/0.7.A
Ballast power 250 watt ballast 230 volt, running current 1.2.A
Ballast will not ignite a hot lamp. The ballast has three attempts to ignite
the lamp then will wait for four minutes before repeating the cycle.
Do not attempt to remove the glass lens while afloat
UL Ti MATE 130 SA
‘submersible through hull light’
150 watt
Part Description 130-S A Part No
1: Projector lid s ecuring plate 00283-B
2: M6 Nut 93381
3: 'O' Ring 00108
4: Gasket NAF 00285-A
5: Connecting ring 00274-C
6: Lamp holder screw 00290
7: Lamp holder (250W) 91195
7: Lamp holder (150W) 91191
8: Reflector collar bush 00288-A
9: M4 Lock nut 93374
10: Lamp (250W ) 91209
10: Lamp (150W ) 91210
11: Reflector adjus tment rod 00284-2-D
12: Reflector complete S91791
13: Glass retaining ring 00476-B
13A: Cap head s crews 93325
14: Glass gaskets NAF 00286-A
16: Body S00475-A
17: Compensating ring 00277
18: Securing ring 00275
19: Cap head screws 93610
20: Ignitor (250W) S95325
21: Projector cover (250W) 00102-H
22: Gland 00107
23: Projector cover (150W) 00102-E
24: Ballast 250 watt S00800-V1W 2
24: Ballas t 150 watt 230v S00800-V2W 2
24: Ballas t 150 watt 120v S00800V3W 2
EARTH TAB AND SCREW
250 watt

 70

UL Ti MATE RANGE - 75 SA & 130 SA INFORMATION
BEAM ANGLE AND LUX INFORMATION
DESCRIPTION
The cone angle in the body restricts the width of the light beam angle. The 50 degree is 65 degrees,
while the flush and UL Ti MATE 130 have an angle of 100 degrees.
The centre of the light beam should be kept to 15 degrees down from the horizontal. Taking into
account the reflector adjustment, a flush body can be installed at an angle of 35 degrees to the vertical.
The spherical is then adjusted to 20 degrees and then locked.
This gives the required 15 degree beam angle.
BEAM ANGLE AND LUX INFORMATION
DESCRIPTION
The above pictures on the left show the directional adjustment. The centre pictures show how the lamp
is moved back to create a tight beam and the right hand pictures shows the lamp moved forward to
create a wide beam.
NOTE- When the lamp is adjusted for a wide beam, the lux level at the centre will decrease but will
increase on the outer part of the beam, giving a more uniform light pattern.
underwater lights limited™
Manufacturers of the Original underwater lights ™
Brand Marine Lighting Products since 1991













