UNEEKOR EYE XO2 User manual

INSTALLATION GUIDE
EYE XO2
IMPORTANT: Read Before Using.

EYE XO2 INSTALLATION GUIDE
2
Notice
Grounding Instructions
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electrical current to reduce the risk of electric shock. This tool is
equipped with an electrical cord having an equipment grounding conductor and a
grounding plug. The plug must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes and ordinances.
Step 1: Hardware Installation Guide
Step 2: Software Installation Guide

EYE XO2 INSTALLATION GUIDE
3
Contents
Section Page
WARNING: To Ensure Safe Use 4 - 5
1. Installation Environment 6
2. Included Items 7
3. Hardware Install
8
3.1 Mounting Bracket
9
3.2 Slide Sensor
10
3.3 Connection
3.4 Connection Status
11
12
5. Software Install 13 - 20
6. Club Sticker Guide 21 - 27
28
Table of Contents

EYE XO2 INSTALLATION GUIDE
4
To Ensure Safe Use
Improper handling or operation of this machine may result in injury or damage to
property. Points which must be observed to prevent injury or damage are described
as follows.
WARNING
Used for instructions intended to alert the user to the
risk of severe injury should the unit be used
improperly.
Used for instructions intended to alert the user to the
risk of injury or material damage should the unit be
used improperly. Material damage refers to damage
to home, furnishing, or anything within the unit’s
vicinity.
NEVER
This symbol alerts the user to items that should never
be carried out.
Safety
Caution

EYE XO2 INSTALLATION GUIDE
5
To Ensure Safe Use - Continued
Install in a level and stable location. Failure to do so may
result in falling of the machine, leading to injury.
Never attempt to disassemble, repair, or modify
shock, or injury. Entrust repairs to a trained technician.
Never use outside or in any location where exposure to
water or high humidity may occur. Do not touch the
power cord or electrical outlet with wet or dirty hands.
Doing so may result in electrical shock.
Conduct play in a clean and brightly lit location.
Operating in a dark or cluttered space may lead to
accidents.
Be aware of your surroundings and use cautiously
with children around. Swinging the club during play
without being aware will result in serious injury or death.
Safety
WARNING
This is a heavy machine.

EYE XO2 INSTALLATION GUIDE
6
Installation Environment
PC Specifications:
Category Requirement
CPU Intel i5 8400 or higher*
RAM 8 GB
Graphics Card GeForceGTX 1060 or higher
Operating System Windows 10 (64bit) Version 1803 or higher
Resolution 1920 x 1080
Connectivity Ethernet Port Required
* AMD: 3rd gen Ryzen or higher and AMD Ryzen 3600 or higher (AMD 2700 is not compatible).
Installation Environment
9’ -

EYE XO2 INSTALLATION GUIDE
7
Included Items
The following items are included with the sensor. Make sure they are all present
and accounted for.
EYEXO2 Sensor Bar Bracket Email – Software Installer Calibration Chart
Power Cable Power Adapter Power Connector USB Ethernet Adapter
Ethernet LAN Cable Level Club Stickers M4 32mm screws
M6 15mm screws M6 15mm high screws M6 15mm low screws
Included Items

EYE XO2 INSTALLATION GUIDE
8
Hardware Install
WARNING
Section 1 “Installation Requirements,” and outline
bracket location on ceiling.
Consult with building manager or landlord about
before installation. The sensor and bracket are
approximately 30 lbs and 9 M4 32mm screws are
required to screw in the bracket and hold the sensor.
Failure to do so may result in serious injury or damage to
property.
CAUTION
Two or more persons are recommended for mounting the
bracket on the ceiling and extreme caution is required
while on the ladder. Failure may result in serious injury or
damage to property.
Ladder Phillips
Screwdriver
M4 32mm
Screw x9 Bracket Sensor Bar
Necessary Tool Necessary Part(s)
Hardware
WARNING

EYE XO2 INSTALLATION GUIDE
9
3.1 Hardware Install - Continued
Step 1: Mount Bracket
The EYE XO2 Sensor and bracket come attached together in the box. Slightly loosen
the black M6 15 mm screws that are holding the sensor to the bracket so you can
remove it. Please make sure you have measured 3.5 feet from the front and middle
of the sensor to your tee position. Do NOT align to the bracket.
Place the ladder under the location on the ceiling where the bracket will be
mounted. Place the bracket flat against the ceiling with the hinges facing down
toward the ground. The longer side of the hinges must be closet towards the
impact screen.
With the bracket in position, grab the 10 silver M4 32mm screws and screw them in
the locations below in the diagram.
M9 32mm (5)
M9 32mm (5)
1
3
2
Hardware

EYE XO2 INSTALLATION GUIDE
10
3.2 Hardware Install - Continued
Step 2: Slide Sensor
After the bracket has been firmly mounted to the ceiling, you will install the sensor
bar.
The sensor bar comes with 6 black M6 15mm screws already inserted; 3 screws in the
front and 3 screws in the back. Make sure all 6 screws are about halfway into the bar
and even in length.
Slide the sensor bar with the 6 screws up and over through the bracket hinges. Make
sure the screws are secured in the hook part of the hinges. Once the sensor is secured
in the bracket hinges, tighten the 6 screws to the bracket.
The tilt of the sensor can be adjusted with the high and low M6 15mm screws. The
regular M6 15mm screws are already screwed into the sensor. You can change this out
with the M6 155 High or Low screws to adjust the angle/ tilt.
M6 15mm
M6 Low 15mm
M6 High 15mm
Hardware
3
1
2

EYE XO2 INSTALLATION GUIDE
11
3.3 Hardware Install - Continued
Step 3: Connection
Ethernet LAN
Cable Power Cord Power Adapter Power Connector
Necessary Parts
Take out the Ethernet LAN
cable from the box. Connect
the end with the tag that reads
“Connect this side of LAN cable
to Sensor ONLY” to the sensor.
Connect the other end
DIRECTLY to your PC ethernet
port and NOT the USB adapter.
Take out all 3 components of
the power source: power
cable, power adapter, and
power connector. Connect all
3 accordingly and connect the
“Power Connector” end
directly to the sensor as
shown below. Turn on red
switch.
Note: The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
An extra green grounding wire is provided on the end of the power connector in case
your outlet is not grounded.
Hardware
1
2

EYE XO2 INSTALLATION GUIDE
12
3.4 Hardware Install – Continued
Step 4: Connection Status
Make sure to check the connection status before you start the
software installation process.
Check and see if the power is on. You will see a bright red light on the switch of
the sensor.
Check and see if your EYE XO2 Sensor and PC are paired through the network.
Hardware
1
2
Please refer to our “Network Setup Guide” below to set the IP
address.
NETWORK GUIDE

EYE XO2 INSTALLATION GUIDE
13
Software Install
WARNING
Please make sure PC requirements are met from section
1 “Installation Environment,” before the installation
process. Failure to do will result in installation issues and
slow gameplay.
WARNING
Please make sure the connection statuses are clear and
everything is paired. Failure to do will result in
installation issues.
Software

EYE XO2 INSTALLATION GUIDE
14
Software Install – Continued
EYE XO2 Installation
You will receive an email with a license code
from your retailer which looks like this:
Please download it and save it to the Uneekor
Folder
Click here: EYE XO2 Installer Link
Ctrl + Click the EYE XO2 Installer link above to begin EYE XO2 Installation or manually enter
the URL: https://download.uneekor.com/dist/EYEXO2/Uneekor_EYEXO2_Setup.exe
Under downloads you will see,
“Uneekor_EYEXO2_Setup.exe” Click
open file.
“Uneekor EYE XO2 (2.10.0.0)
Setup” will open. Click “Next.”
Software
2
3
4
1
EYEXO2_30000XXXXX.license.

EYE XO2 INSTALLATION GUIDE
15
3.5 Software Install – Continued
EYE XO2 Software Installation
Keep the destination folder as
“C:\Uneekor” and click Install.
Please wait while installer
completes installation.
5
6
Software

EYE XO2 INSTALLATION GUIDE
16
3.6 Software Install – Continued
EYE XO2 Software Installation
**If these two pop-ups occur, please
hit ok for both.
The “Run Uneekor EYE XO2” is
checked. Uncheck it and click finish.
7
Software

EYE XO2 INSTALLATION GUIDE
17
3.7Software Install - Continued
EYE XO2 Sensor Activation
Go to the C: Drive-> Uneekor Folder -> Device -> Launch Monitor -> EYEXO
Find and double click “EYEXO2_Check”
In the “EYEXO” folder click on
“EYEXO2_Activation”
Click “Browse” to find the license key
saved from step 1 above.
Then click “Activation”
After adding the license please click
“Activate.”
The EYE XO2 Sensor installation is
now complete.
2
If you don’t get the Sensor LAN connection, please
refer to our “Network Settings Guide.”
Make sure the Sensor LAN connection is good before
the software installation process.
1
EYEXO2_40000XXXXX.license
Software

3.8 Software Install - Continued
EYE XO2 Network Config
1Once the sensor has been activated,
you will have a screen like the one
on the right. Click Set Network
Param & Firewall to continue
2After the selection, you will be asked
to restart the PC. Click Yes to restart
to finish the Sensor installation

3.8 Software installation - Continued
EYE XO2 Calibration
To complete the installation of the EYE XO2.
Follow the calibration guide linked below:
EYE XO2 Calibration Guide
EYE XO2 INSTALLATION GUIDE 19

EYE XO2 INSTALLATION GUIDE
3.9Software Install – Continued
VIEW Software Installation
Click here: VIEW Installer
Ctrl + click on the VIEW Installer above or enter the URL manually:
https://download.uneekor.com/dist/View/VIEW_Setup.exe
Open downloads on the right.
If you receive this warning, follow the
steps below.
3.8.1 Hover over the download,
click the 3 dots on the right
side, and click keep.
3.8.2 Click the “Show more” drop
down and click “Keep anyway.”
3.8.3 Then click “Open file” under
downloads.
“VIEW_SETUP 20220721 Setup” will
open. Click “Next.”
Software
1
2
EYE XO2 INSTALLATION GUIDE 20