UNEEKOR EYEXO User manual

IMPORTANT: Read Before Using.

2
EYEXO INS T ALL GUIDE
In the event of a malfunction or breakdown, grounding provides a path of
least resistance for electrical current to reduce the risk of electric shock.
This tool is equipped with an electrical cord having an equipment grounding
conductor and a grounding plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in accordance with all local
codes and ordinances.
Step 1: Hardware Installaion Guide
Step 2: Software Installaion Guide
Notice
Grounding Instructions

3
EYEXO INS T ALL GUIDE
Contents
Section Page
WARNING: To Ensure Safe Use 4 - 5
1. Installation Environment 6
2. Included Items 7
3. Hardware Install
3.1 Mounting Bracket
3.2 Slide Sensor
3.3 Connection
8
9
10
11
4. Connection Status 12
5. Software Install 13 - 21
6. Club Sticker Guide 22 - 26
27
Table of Contents

4
EYEXO INS T ALL GUIDE
To Ensure Safe Use
Improper handling or operation of this machine may result in injury or damage
to property. Points which must be observed to prevent injury or damage are
described as follows.
WARNING
NEVER
CAUTION
Used for instructions intended to alert the user to the
risk of severe injury should the unit be used improp-
erly.
Used for instructions intended to alert the user to the
risk of injury or material damage should the unit be
used improperly. Material damage refers to damage
to home, furnishing, or anything within the unit’s
vicinity.
This symbol alerts the user to items that should nev-
er be carried out.
Safety

5
EYEXO INS T ALL GUIDE
Install in a level and stable location. Failure to do so
may result in falling of the machine, leading to injury.
Never attempt to disassemble, repair, or modify
shock, or injury. Entrust repairs to a trained
technician.
Never use outside or in any location where exposure
to water or high humidity may occur. Do not touch
the power cord or electrical outlet with wet or dirty
hands. Doing so may result in electrical shock.
Conduct play in a clean and brightly lit location.
Operating in a dark or cluttered space may lead to
accidents.
Be aware of your surroundings and use
cautiously with children around. Swinging the club
during play without being aware will result in serious
injury or death.
This is a heavy machine.
WARNING
To Ensure Safe Use - Continued
Safety

6
Installation Environment
EYEXO INS T ALL GUIDE
1. Installation Environment
* AMD: 3rd gen Ryzen or higher and AMD Ryzen 3600 or higher (AMD 2700 is not compatible).
Catagory Requirement
CPU Intel i5 8400 or higher*
RAM 8 GB
Graphics Card GeForceGTX 1060 or higher
Operating System Windows 10 (64bit) Version 1803 or higher
Resolution 1920 x 1080
Connectivity Ethernet Port Required
3.5’
9’-10’

7
EYEXO INS T ALL GUIDE
EYEXO Sensor Bar Bracket USB - Software Calibration Chart
Power Cable Power Adapter Power Connector USB Ethernet Adapter
Ethernet LAN Cable Level Club Stickers
2. Included Items
The following items are included with the sensor. Make sure they are all
present and accounted for.
Included Items
M6 15mm screws M6 15mm high screws M6 15mm low screws
M4 32mm screws

8
EYEXO INS T ALL GUIDE
Ladder Phillips
Screwdriver
M4 32mm
Screw x9 Bracket Sensor Bar
Section 1 “Installation Requirements,” and outline
bracket location on ceiling.
Consult with building manager or landlord about
before installation. The sensor and bracket are
approximately 30 lbs and 9 M4 32mm screws are
required to screw in the bracket and hold the sensor.
Failure to do so may result in serious injury or
damage to property.
Two or more persons are recommended for
mounting the bracket on the ceiling and extreme
caution is required while on the ladder. Failure may
result in serious injury or damage to property.
3. Hardware Install
WARNING
WARNING
CAUTION
Necessary Tool Necessary Part(s)
Hardware

9
EYEXO INS T ALL GUIDE
1The EYEXO Sensor and bracket come attached together in the box. Slightly
loosen the black M6 15 mm screws that are holding the sensor to the
bracket so you can remove it. Please make sure you have measured 3.5 feet
from the front and middle of the sensor to your tee position. Do NOT align to
the bracket.
3With the bracket in position, grab the 10 silver M4 32mm screws and screw
them in the locations below in the diagram.
3.1 Hardware Install - Continued
Step 1: Mount Bracket
Hardware
2Place the ladder under the ceiling mounting position. Climb the ladder to a
hinges facing down towards the ground. The longer side of the hinges must
be closest towards the hitting screen.
M9 32mm (5)
M9 32mm (5)
3.5’

10
EYEXO INS T ALL GUIDE
1sensor bar.
The sensor bar comes with 6 black M6 15mm screws already inserted;
3 screws in the front and 3 screws in the back. Make sure all 6 screws are about
half way screwed into the bar and even in length.
2Slide the sensor bar with the 6 screws up and over through the bracket
hinges. Make sure the screws are secured in the hook part of the hinges.
Once the sensor is secured in the bracket hinges, tighten the 6 screws to
the bracket.
3.2 Hardware Install - Continued
Step 2: Slide Sensor
Hardware
3The tilt of the sensor can be adjust with the high and low M6 15 mm screws.
The regular M6 15 mm screws are already screwed into the sensor. You can
change this out with the M6 15 mm High or Low screws to adjust the angle/tilt.
M6 15mm
M6 Low 15mm
M6 High 15mm

11
EYEXO INS T ALL GUIDE
1Take out the Ethernet LAN
cable from the box. Connect
the end with the tag that
reads “Connect this side of
LAN cable to Sensor ONLY”
to the sensor. Connect the
other end DIRECTLY to your
PC ethernet port and NOT a
switch.
2Take out all 3 components
of the power source: power
cable, power adapter, and
power connector. Connect all
3 accordingly and connect the
“Power Connector” end directly
to the sensor as shown below.
Turn on red switch.
3.3 Hardware Install - Continued
Step 3: Connection
Ethernet LAN
Cable Power Cord Power Adapter Power Connector
Necessary Parts
Hardware

12
EYEXO INS T ALL GUIDE
1Check and see if the power is on. You will see a bright red light on the
switch of the sensor.
2Check and see if your EYEXO
Sensor and PC are paired
through the network.
Please refer to our “Network Settings Guide” to set the
IP address.
3Insert the USB memory stick
Make sure the Sensor LAN connection is good
before the software installation process.
If you don’t get the Sensor LAN connection, please refer
to our “Network Settings Guide.”
4. Hardware Install - Continued
Make sure to check the connection status before you start
the software installation process.
Hardware

13
EYEXO INS T ALL GUIDE
5. Software Install
Please make sure PC requirements are met from
section 1 “Installation Environment,” before the
installation process. Failure to do will result in
installation issues and slow gameplay.
Please make sure the connection statuses are clear
and everything is paired. Failure to do will result in
installation issues.
WARNING
WARNING
Software

14
EYEXO INS T ALL GUIDE
1Insert USB - memory stick from the box into your PC.
2You will receive an email with a license code from [e-mail]
which looks like this: QED_30000XXXXX.license.
Please download it and transfer it to the USB.
3Open QED Installation Wizard
from your USB.
4Click “browse” once the
window opens and search for
the QED license from step 2.
QED_30000XXXXX.
license
5.1 Software Install - Continued
USB Software
Necessary Part(s)
Software

15
EYEXO INS T ALL GUIDE
5Click next and you should see
this window.
61. The 3 softwares from
the “Required Software”
section: “Aio-runtimes,”
“Teamviewer10,” and
“DirectX.”
2. The 2 softwares from
“Sensor Software” section:
“EYEXO Sensor & EYEXO
Activation”
3. Software Section:
“VIEW,” “QED
Succeed.” This will depend
on your purchase.
Please install each
software one at a time. Click
“Install” button for each install.
“Aio-Runtimes” must be
Go to next page for steps.
5.2 Software Install - Continued
1
2
Software
3

16
EYEXO INS T ALL GUIDE
1Please select all “Visual C++
rest.
These ”Visual C++ Runtime
and the game. Then Click
“Install.”
(If you do not see the “Visual
already has these downloaded from
another install)
Alo-runtimes
2Please select “Basic
Installation” and “Personal/
non-commericial use”
settings for the installation of
Teamviewer.
Teamviewer
3Please select “I accept the
agreement” and click “Next >”
Continued on page 17
Direct X
5.3 Software Install - Continued
Software

17
EYEXO INS T ALL GUIDE
3Click “Finish” when the
download is complete.
Direct X
4Click “Next” to start the
EYEXO Sensor install
in the setup window.
EYEXO Sensor
5Default destination folder will
be in C: Drive. If you would like
to change the destination click
“Browse...” and choose your
folder.
Click “Install” to start the
install.
5.4 Software Install - Continued
Software

18
EYEXO INS T ALL GUIDE
6You will see this screen once
the install has started.
7The “Run EYEXO Sensor
is checked. Uncheck it and
click ”Finish.”
8license key.
Then click “Activation.”
Continued on page 19
EYEXO Activation
QED_30000XXXXX.license
5.5 Software Install - Continued
Software

19
EYEXO INS T ALL GUIDE
8If nothing happens during the
EYEXO Sensor Activation, you
can activate it another way.
Go into your C:Drive > Open
“EYEXOSensor” > Open
“EYEXO_U_Activation.” > Browse
9Depending on what package
you purchased/paid for,
you will be only allowed to
install.
NOTE: All EYEXO sensors come
with “VIEW” software.
Install “VIEW” software
REFINE,” or
“QED SUCCEED,” depending
on your purchase.
QED Software
5.6 Software Install - Continued
Software

20
EYEXO INS T ALL GUIDE
10 Click the “VIEW 1.0
Then click the “Install” button
on the next window.
11 License file from step
4, then click activation.
“Finish”
5.7 Software Install - Continued
QED_30000XXXXX.license
Software
VIEW Activation