UNEEKOR QED Manual

Installation Guide
TRUSTWORTHY GOLF SIMULATOR
Step 1: Hardware Installation Guide
Step 2: Software Installation Guide

Notice
Grounding Instructions
In the event of a malfunction or breakdown, ground-
ing provides a path of least resistance for electrical
current to reduce the risk of electric shock. This tool is
equipped with an electrical cord having an equipment
grounding conductor and a grounding plug. The plug
must be plugged into a matching outlet that is prop-
erly installed and grounded in accordance with all
local codes and ordinances.
Do not modify the plug provided. If it will not fit the
outlet, have proper outlet installed by a qualified
electrician.
UNEEKOR, INC.
3155 W. BIG BEAVER RD SUITE 108
TROY, MI 48084

Contents
Warning - To Ensure Safe Use
Contents
1. Installation Environment
2. Included Items
3. Hardware Install
4. Connection Status
5. Software Install
6. Specifications

Warning - To Ensure Safe Use
Improper handling or operation of this machine may result in
injury or damage to property. Points which must be observed
to prevent injury or damage are described as follows.
Used for instructions intended to alert the
user to the risk of severe injury should the unit
be used improperly.
WARNING
This symbol alerts the user to items that
should never be carried out.
NEVER
Used for instructions intended to alert the
user to the risk of injury or material damage
should the unit be used improperly. Material
damage refers to damage to home, furnish-
ing, or anything within the unit’s vicinity.
CAUTION

To Ensure Safe Use - Continued
WARNING
This is a heavy machine.
Install in a level and stable location.
Failure to do so may result in falling of the
machine, leading to injury.
Conduct play in a clean and brightly lit loca-
tion. Operating in a dark or cluttered space
may lead to accidents.
Be aware of your surroundings and use
cautiously with children around. Swinging the
club during play without being aware will
result in serious injury or death.
Never attempt to disassemble, repair, or
modify the machine. Doing so may result in
fire, electrical shock, or injury.
Entrust repairs to a trained technician.
Never use outside or in any location where
exposure to water or high humidity may occur.
Do not touch the power cord or electrical
outlet with wet or dirty hands. Doing so may
result in electrical shock.

1. Installation Environment
PC Specifications
- CPU: Intel i5 8400 or higher.
- RAM: 8GB.
- Graphics: GeforceGTX 1060.
- Operating System: Windows 10 (64 bit)
ㅤVersion 1803 and higher.
- Resolution: Full HD.
13 ‘


2. Included Items
The following items are included with the sensor. Make
sure they are all present and accounted for.
Power Cable (1)
QED Sensor Bar Bracket USB - Software Calibration Chart
Marked Balls (24) M4 32mm
Power Adapter (1) Power
Connector (1)
USB Ethernet
Adapter (1)
M6 15mm
Ethernet
LAN Cable (1)

3. Hardware Install
WARNING
WARNING
CAUTION
Confirm installation requirements are
met from Section 1 “Installation Require-
ments,” and outline bracket location on
ceiling.
Consult with building manager or land-
lord about the specifications and weight
capacity of the ceiling before installa-
tion. The sensor and bracket are approxi-
mately 30 lbs and 9 M4 32mm screws are
required to screw in the bracket and hold
the sensor. Failure to do so may result in
serious injury or damage to property.
Two or more persons are recommended
for mounting the bracket on the ceiling
and extreme caution is required while on
the ladder. Failure may result in serious
injury or damage to property.
Ladder
Necessary Tool
Phillips screwdriver
Necessary Tool Necessary Parts
M4 32mm Screw x 9
Necessary Parts
Bracket
Necessary Parts
Sensor Bar

3.1 Hardware Install
Place the ladder under the ceiling mounting position.
Climb the ladder to a comfortable position and place the
bracket flat against the ceiling with the hinges facing
down towards the ground and the logo closest towards
the hitting screen.
2
With the bracket in position, grab 9 silver M4 32mm
screws and screw the first two screws in order according
to the diagram below. Then screw in the rest in any order.
3
1
2
1. Mount Bracket
1
Make sure this center point is aligned with tee position on mat.
The QED Sensor and bracket come attached together in the
box. Slightly loosen the black M6 15 mm screws that are
holding the sensor to the bracket so you can remove it.

2. Slide Sensor
3.2 Hardware Install
After the bracket has been firmly mounted to the ceil-
ing, you will install the sensor bar. The sensor bar
comes with 6 black M6 15mm screws already inserted; 3
screws in the front and 3 screws in the back. Make sure
all 6 screws are about half way screwed into the bar and
even in length.
1
Slide the sensor bar with the 6 screws up and over
through the bracket hinges. Make sure the screws are
secured in the hook part of the hinges. If the screws do
not go into the hinges, adjust by tightening the screws
just a little.
2

3. Connection
Take out the Ethernet LAN cable from the box. Connect
the end with the tag that reads “Connect this side of
LAN cable to Sensor ONLY” to the sensor. Connect the
other end DIRECTLY to your PC ethernet port and NOT a
switch.
1
Take out all 3 components of the power source: power
cable, power adapter, and power connector. Connect all
3 accordingly and connect the “Power Connector” end
directly to the sensor as shown below. Turn on red
switch.
2
Ethernet LAN Cable
Necessary Tool
Power Cable
Necessary Tool Necessary Parts
Power Adapter
Necessary Parts
Power Connecter

4. Connection Status
Make sure to check the connection status before you start
the software installation process.
Check and see if the power is on. You will see a bright red light
on the switch of the sensor.
Check and see if your QED Sensor and PC are paired through
the network - static IP address.
Insert the USB memory stick
and find and double click:
2
3
1
Please refer to our “Network Settings Guide” to set the IP
address.
Make sure the Sensor LAN connection is good before the
software installation process.
If you don’t get the Sensor LAN connection, please refer to our
“Network Settings Guide.”

5. Software Install
WARNING
Please make sure PC requirements are met from
section 1 “Installation Environment,” before the
installation process.
Failure to do will result in installation issues and
slow gameplay.
WARNING
Necessary Parts
USB - Software
Please make sure the connection statuses are clear
and everything is paired. Failure to do will result in
installation issues.

5.1 Software Install
1
2
Insert USB - memory stick from the box into your PC
QED_30000965XXXX.license
You will receive an email with a license code
from [e-mail] which looks like this:
Please transfer it to the USB.
3Open QED_Installation_wizard from your USB
4Click “browse” once the QED Installer opens
and search for the QED license from step 2
QED_30000965XXXX.license

5.2 Software Install
5Click next and you should see this window.
6
The 3 softwares from the “Required Software” section:
“Aio-runtimes,” “Teamviewer10,” and “DirectX.”
The 2 softwares from “Sensor Software” section:
“Z3CAM Sensor & Z3CAM Activation”
Activation
QED Software Section: “QED_Ignite,” “QED_Refine,”
and “QED_Suceed.” This will depend on your purchase.
Description:
Please install each software one at a time ONLY. Click
“Install” button for each install. “Aio-Runtimes” must be installed
first. Go to next page for steps.

5.3 Software Install
1Please select only “Visual C++ Runtime files, and unselect the rest.
These ”Visual C++ Runtime files are required to run tools and
the game. Then Click “Install.”
(If you do not see the “Visual C++Runtime files it means your PC
already has these downloaded from another install)
2
Aio-runtimes:
Teamviewer:
Please select “Basic Installation” and “Personal/non-commericial
use,” settings for the installation of Teamviewer.
Steps:

5.4 Software Install
Direct X:
Please select “I accept the agreement” and
click “Next >”
UNCHECK the “Install the Bing Bar” option and
then click “Next>”
Click “Finish” when the download is complete.
3

5.5 Software Install
4Z3CAM Sensor:
Click “Next” to start the Z3CAM sensor install
in the setup window.
5Default destination folder will be in C: Drive. If you would like
to change the destination click “Browse...” and choose your
folder. Click “Install” to start the install.

5.6 Software Install
6You will see this screen once the install has started
7The “Run Z3CAM Sensor 1.0 is checked. Uncheck it and click ”Finish.”

5.7 Software Install
Z3CAM
QED_30000965XXXX.license
Z3CAM Activation:
Click “Browse” to find that QED_License code from step 4. Then click
“Activation.”
8