Uni-Ubi Uface 4 Installation and operation manual

PRODUCT
BOOKLET
Uface 4
( OS-M345E1-V-R23WFCQ )

Parts list
No. Quantity
Name
Unit: mm
/1 / 2
Instruction
1 1
3 1
4 1
1 5
Host
6
7 1
1
Hexagon wrench
8 2Tamper screws
Power adapter 12
User manual
Wall-mount support
Installation sticker
49
10 4
4*30 Countersunk self-tapping screws
Expansion pipes
Dear customer,
Thank you for using our product. For better use, please carefully read this instruction. If you have any
issues not mentioned here, please contact the provider. All parts of this booklet are reserved by our
company, including words, pictures and graphics. Without written permission, no unit or individual
shall extract, copy, translate or edit the content in this instruction.
Device introduction
Parts list
Dimensional drawing
Platform/Software
Operating Instruction
Appearance description
Illumination intensity
Position
Height
Steps
Wiring connection
Features
FAQ
Installation
Product description Dimensional Drawing
Platform/Software Operating Instruction
Appearance description
Please mark the need for software version when place the order. For more detailed platform/software
Infrared camera
RGB camera
Support slot
Cooling hole
Power input
Switching value
WG OUT
ALARM INPUT
RS232
WG IN
WG_IN_D1
WG_IN_D0
GND
WG IN
RS232_RX
RS232_TX
GND
RS232
ALARM-KEY
ALARM-DOOR
GND
ALARM INPUT
WG_OUT_D1
WG_OUT_D0
GND
WG OUT
DOOR_NC
DOOR_COM
DOOR_NO
Switching value
Screw hole of support
Wiring socket
Tamper switch
Ethernet port
USB interface
Reset button

3 / 4
When the sunlight shines indoor through the window, the face
recognition terminal device shall not be installed in shown black
shadow area, instead, shall be installed in place with little
sunlight impact, no side-light and no backlight. (Glass window
can be deemed as no walls)
Sunlight shines indoor
If the room has glass wall, there is no shield for sunlight, then it
is suggested to hang curtains over the window, and install the
the recognition. (Glass window can be deemed as no walls)
Glass window
Indoor
Door
Light
Wall/Shields
Indoor
Door
Light
Wall/Shields
Indoor
Door
Door
Wall/Shields
Indoor
Door
Wall/Shields
Light
Light
Illumination intensity
Test object
Light source
Device
image and registered image; backlight, side-light and
(Analysis: from the view of human eyes, the color
changes on face skin may result in wrong recognition
of identity; unclear exposure area, no matter large or
small, may result the identity judgement.)
The test standard is as shown on the picture:
the angle between dotted line A and dotted line
B is 90 ° , the test adopts the common light
meter with full spectrum, and applies U30 stan-
dard light source, adjust the distance between
source light and test object, subject to the
illumination intensity of the object face at this
time.
Illumination intensity in actual scenarios
Reference to intensity
Intensity test
The recognized face, of which, the illumination
intensity “intensity” in short) shall not be lower
than 30 Lux
when the device put in a totally dark environ-
ment, the face illumination intensity, 0.5m
distance to the device, is about 100 Lux. The
nearer to the device, the higher the intensity is.
If there is overexposure on the face, the face
characteristics will be unable to be extracted
and may lead to hard recognition.
500Lux,
overexposure
30 Lux, dim
100 Lux, bright
50 Lux, normal
300 Lux,
slight exposure
Back light
Side light
Light source is near to the object
Device stands between the light
source and object
Object stands between the
device and light source
Side-light may lead to uneven
light on the face
Backlight may make the
face too dark
Direct strong light may
cause overexposure
Strong light
1. Install the device in a place with little impact
from light source.
2. Add a registered image according to the site
condition, and it is suggested to use this product
to enroll images.
3. Properly lower the threshold value according to
usage.
Improvements
Device shall be installed in places avoiding backlight, side-light and strong light.
Position
This place, 3m away from the window, or does not
Backlight, side-light or direct strong light,
not suitable for installation.
Other areas, install in suitable places according
to actual light impact. Glass window (same as the semi-outdoor scene
with no walls)
Device Light
DoorWall
Person
Curtain
Glass wall
Sunlight shines through the door, the device shall be installed at
the place with shields and little light impact. Glass window can
be deemed as no shields, the device shall be installed at the side
without glass window or with curtain hung.
Sunlight shines through the door, with glass window
at one side
Sunlight shines through the door, the device shall be installed at
the place with shields and little light impact.
Sunlight shines through the door
FOV(V)
Height
Camera vertical wide-angle Camera horizontal wide-angle
Wall
1.4m
Device
Gate
User
2m
Recognition area
FOV(H)
Suggested installation height
(distance between the screen
and the ground) is 1.4m, as the
reco g niza b le body he i g ht
range, 0.5m distance away
from the device, is 1.3m-1.7m;
the recognizable body height
range, 1m distance away from
the device, is 1m-2m. (There
are some deviations)

5 / 6
1Paste the installation sticker on the wall, and keep the horizontal line parallel with the ground
and the red line 1.4m distance to the ground; drill screw holes on suitable position on the wall
according to the installation method (if use 86-box, then no need to drill holes), drill 1~2 outlet
holes according to wiring need.
3Align the interface socket and Ethernet port with device back and insert.
2the support. 4Thread the tamper screws into the support and rotate 2 turns, then align the bottom slot with
the support hook, use the hexagonal wrench to tighten screws following the shown direction.
Installation completes.
Steps
Attention: If the wall has hard foundation, self-tapping screws shall be used together with
expansion pipe; if the wall has soft foundation, use self-tapping screws directly.
1.4M Outlet hole
1.4m calibration line

Wiring for magnetic door Wiring for automatic door
Installation notes
7 / 8
1. When arrange the wires, if the 12V power supply cable of the host does not adopt the “Special power strip”
and is in long distance, resulting in large resistance, then abnormal phenomena may occur easily such as
shown as follow.
2. The power adapter is put together with the device which is optional, such as EU standard, American
standard, UK standard, and so on.
System installation schematic
drawing for magnetic door
Wiring schematic drawing for touching
switch of magnetic door
System installation schematic
drawing for automatic door
Wiring schematic drawing for mechanical
switch of magnetic door
Wiring schematic drawing for sensor
switch of automatic door
Access control
relay interface
DC12V Ethernet
Host
Power
Door exit
(inside)
Magnetic lock
Host
Access control
relay interface
~
Ethernet
PUSH
GND
12V
COM
NC
NO
12V
GND
NO
NC
COM
12V
12V
Power
Door exit
Magnetic lock
Ethernet
Host
Power Relay
Opening signal PUSH
Public end GND
12V
Controller of auto-door (only used terminals will be listed)
Ethernet
DC+
DC-
NO
COM Sensor
DC+
DC-
NO
COM
Host
Power Relay
NO
NC
COM
Door exit
PUSH
GND
12V
COM
NC
NO
12V
12V
Host
Power
Magnetic lock
Ethernet
Power Relay
Power
GND
12V
Cable equivalent
resistance1
Cable equivalent
resistance 2
Voltage meter
V
Host
Wiring connection
Auto-door controller
+ assembly units Sensor (inside)
•
•
•
•
power supply for the host end, and abnormal phenomena like repeat restart, system crash may
occur. If the power is far away from the device, the power cable can be extended (strong current).
may cause repeat restart.
multi-strand cable in parallel or use copper core bold cable, to ensure voltage >11V.
Attention: If use network cable, the extension cable use 4-strand cable as positive pole and 4-strand cable as negative pole.
If not clear with how to extend, please contact the provider to change “Special power strip”.

9 / 10
FAQFeatures
•Secondary development (integrated)
Support the interface connection in HTTP; supports 232 serial output, Wiegand 26 and
•Complete functions
-
tion and stranger detection.
•High extensibility
Supports deployment methods like public network and LAN; supports screen display
• Try to restart and reset
When the device stops in some interface for a long time, users can plug out the
can long press RESET hole for 8-12s to restart the device. Besides, users can
• Protection
This product possesses certain capbility of self-protection, as it can prevent
small objects (such as tools, wires and so on) from entering and touching
internal parts.
• Drop resistance
Please avoid operations such as falling, breaking, bending, heavily pressing and
so on.
• Cleaning
Please use soft cloth or such materials, lightly wipe the display screen or panel,
and to avoid scrubbing with water and cleaner.
•Working environment
The normal working temperature for this device is -20ºC~50ºC, if the actual
device.
Do not dirty or damage the display
screen with oil-water or sharp objects
Do not use unknown power adapter to
avoid burning out the device
Recognition speed less than 1s.
• Quick recognition speed
• Characteristics
Completely solve image frauds in all kinds of carriers with infrared and RGB dual-camera;
when face database is 10-thousand. the recognition accuracy is 99.99% ((99.77%
recognition rate under 1% false accept rate; 99.27% recognition rate under 0.1% false
accept rate).
• Store records in local
Store 10-thousand level database in local
Device supports storing 10 thousand pieces of face images, 30-thousand pieces of
recognition records (including on-site photo storage).

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.