UNIHOMS S8E Operational manual

User Manual
Product
6 inch
Control Panel
6”Smart Multi-functional Control Panel(in-wall)

Chapter 1 Product presentations........................................................3
1.1 Appearance.................................................................................3
Chapter 2 Product Specifications....................................................... 4
PX30 Quad core Cortex-A35........................................................4
Chapter 3 Ports and Specifications....................................................5
3.1 Interface and ports.............................................................. 5-6
3.2 Specifications............................................................................. 7
Chapter 4 Installation instructions.....................................................8
4.1 Installation drawings............................................................... 9
4.2 Wires connection drawing.................................................. 11
Chapter 5 Operation guideline.........................................................12
5.1 Safety Notes*****....................................................................11
5.2 Operation guideline.............................................................. 12
TABLE OF
CONTENTS

Chapter 1 Product presentation
1.1 Appearance
1.2 Main Features
● Fit Asian 86mm*86mm wall boxes, simple inwall installation.
● 6-inchHDLCD,IPS,multitouchscreen,quadruple
microphone with noise reduction, Auto light sensor, built in
1W speaker.
● ZigBee gateway function, APP remote control.
● Control the lights, curtains, air conditioners, and all other
Smart Home devices. Configure smart home scenes in the
APP, turn on the scene mode with one touch on the screen.

Chapter 2 Product Specifications

Chapter 3 Ports and Specifications
3.1 Interface and ports

3.2 Specifications

Chapter 4 Installation instructions
● Turn off the main power in the electricity box and confirm
the fire wire is not alive with a test pencil.
● Remove the base of the smart panel and install it in the wall
box (as shown in the pictures following).
● Check the wires and make sure the wires are in good
contact with the terminals and no exposed cooper wires.
● Fasten the base to the wall box with mounting screws and
fix the smart panel back to the base.
● Note that the screws should not be fixed too tight during
installation in case any deformation or damage to the screen
and hardware.
● If your smart panel is not flat after installation, do not press
the screen violently, please check the wall box and the base
installation at first.

4.1 Installation drawings

Depth of the wall box should be more than 50mm.
Note: Make sure the circuit power were cut off before wire
connections!
Circuit breaker used as disconnected device shall be
incorporated in the electrical installation of the building.
4.2 Wires connection drawing

Chapter 5 Operation guideline
5.1 Safety Notes*****
●The product must be installed by professional electricians.
● Turn off the main power in the electricity box and confirm
the live wire is

not alive with a test pencil.
● The product should be kept away from fire and water
during installation and use.
● The product can not be used in moisture circumstances
such as bathroom.
● Please note the product does not support POE power
supply. Do not connect PoE switch to this product which
would cause damage to the product.
5.2 Operation guideline
*This operation guideline is based on Unihoms ZigBee,
Unihoms
App,Unihoms cloud platform and Smatek S8E firmware. If
any other platforms or firmware, please follow their
operation guidelines.
(1) The product will be turned on once you connect it to the
power supply. The product will get to the network settings
when you start it in the first time. You can also get into the
network settings from the select menu by dropping down
from the top of the LCD screen.

(2) There are two options in the network settings. You can
select wireless connection or wired connection. There will
be a QR code showing on the screen after the network
connection is done.

(3) Start the Unihoms App in your smart phone, select the “ ”
at top right corner in the App home page, and then select the
“ ”at top right corner in the App page.
(3) Scan the QR code on the screen of the product to add it
into the Unihoms App. You will find an S8E panel icon in your
App.

Long press switch 1 or switch 2 to change the name of the switch.
（ 4 ） Get into the product interface in the Unihoms App, you will
see the gateway and switch icons like and .Click the switch icon to
control 2 local switches (load of each switch for lamps should be
no more than 200W.). It means the switch is off when the icon is in
grey, and the switch is on when it is in orange.

You will see the following pictures in the Unihoms App
when you are adding sub devices to the gateway. Make
sure the sub devices are in the set-up mode and the LED
indication light is flickering.
(5) Click the gateway icon to add ZigBee sub devices.
Make sure the ZigBee sub devices are in the set-up mode.
The gateway will search and add the sub devices
automatically. You can follow the user manual of the sub
devices to make sure it is in set-up mode. (Usually it is
long press the power button or the reset button in 5s,
then the LED indication light flickering which means it is
in the set-up mode.)

(6) Click the finish button on the App after you add the sub
device successfully. For example (3 gang switch) as the
following.

(7) You could change the name of the sub devices after they
are added to the gateway successfully.
(8)
(9) You could change the device type by getting into the
device interface in the App. It means the switch is off when
it is in grey, and the switch is on when it is in green. You
could also set up timers(Schedule) for the switches to
realize the automation control.

(10) To create scenes,enter Unihoms smart App-Scene- Tap-
to-Run (not Automation) - create scenes - Launch
Tap-to-Run-Then -Runthedeviceandconfiguredifferent
devices work at the same time as a scene. And you can
rename your scenes.
Swipe down and click sync to have your devices and scenes
sync to panel, now one tap on panel, whole home
automation.

If there is any questions when you add some other sub
devices or scenes, please contact us for support.