Unique Automation Bathomatic Basic User manual

1
Bathomatic Basic
Installation Guide
Unique Automation Ltd.

2
Introduction
Thank you for purchasing Bathomatic. This guide covers the installation of the mechan-
ical and electrical components of Bathomatic. Please read the guide carefully and keep
the booklet handy for future reference.
Contents
Introduction...............................................................................................................................................................................
Parts Checklist........................................................................................................................................................................
Installation
Part 1: Mechanical Components...................................................................................................................
Part 2: Electrical Components.......................................................................................................................
2
3
4
10

3
Parts Checklist
Bathomatic Basic contains:
• Bathomatic Eco Drain and Overow Assemblies
• Bathomatic User Interface
• Water Mixer
Visit https://uniqueautomation.co.uk for a list of downloads relating to your
product, including 3D models of all parts included with Bathomatic Basic.

4
Installation
Part 1: Mechanical Components
Part 1 of the installation guide covers how to install the mechanical components
that make up the bathomatic system.
This section will guide you in assembling the motorised drain and overow sub-
units, and in connecting them via the drainage pipe.
The product may be installed in a loft space, under the bath or in a convenient
cupboard space, providing there is enough room for maintenance. Note that
installation must be conducted by designated, qualied and competent personnel.
Drain sub-
unit
Assembled
mechanical
components
Overow
sub-unit

5
• Fit lower drain pieces together, and position the parts so they are
each facing desirable directions. Note: The washer comes in differ-
ent sizes to compensate for various bath thicknesses
• Insert strainer and screw in loosely.
1
2• Use the xing tool provided to tighten the strainer
• Remove the xing tool. Keep it handy for removing the drain at a
later date.

6
• The drain plug is shown below. The bottom screw can be adjusted
depending on the thickness of your bath using the nut.
• Insert the drain plug into the top of the strainer.
4
3
• Attach the overow pipe to the drain body by rst feeding one end
through the ange, ring and seal as shown, ensuring the tapered
end of the seal faces the drain body.
• Insert the pipe into the drain body and tighten the ange.

7
• Place the overow body and seal at the back of the overow hole. If
the bath wall is thin, an additional seal may be required.
• Insert the outlet and the nut. Note: use moderate force when
tightening the nut, as overtightening may cause a crack to develop.
6
5• Attach one side of the P-Trap to the drain body by tightening the
ange on the P-trap over the bottom thread.
• Similarly, attach the other side of the P-Trap to the drain pipe.
• A shallow version is available if there is little space under the bath.

8
8• Place the drain cover into the strainer and press down hard until it
clicks. The cover can still be removed afterwards.
• Place the overow cover onto the outlet.
• Attach the other end of the overow pipe to the overow body as
shown.
7

9
9
10
• Fasten the water mixer to the wall or oor with screws.
• Be aware that the unit must be installed in the correct orientation,
so that no water pipes are facing downwards.
• Attach the outlet of the water mixer to the overow body.

10
Installation
Part 2: Electronic Components
Part 2 of the guide covers the installation of the electronic components of the
bathomatic system.
1
VAC
• Ensure that the wiring for the bathomatic system is attached as
follows, and that the yellow-sheathed wire coming from the 3-pin
junction is properly grounded.

11
2• Before mounting the module, ensure that there are no nearby
sources of heat such as radiators, hot water pipes and direct
sunlight
• Ensure that the interface is not at risk of direct contact with water.
• Insert the box into a 75x75mm hole in drywall.
• Arrange the xing wings and tighten their screw heads.
• Connect the module to the ethernet power cables.
• Insert the display into the box by aligning the connector pins.