Unit UT-P32 User manual

■UT-P30
■UT-P32
INSTRUCTION MANUAL
使用說明書
有源差分探頭
Differential Probe Active Probe

目錄
1、簡述.................................1
2、規格.................................1
3、操作環境及狀況.......................2
4、操作程序.............................3
5、 維護................................3
6、 清潔.................................4
7、 保固.................................4
8、 維修.................................4
CONTENTS
1、Features..........................5
2、Specifications.....................5
3、Operating environmental conditions....7
4、Operating procedure................7
▉Maintenance......................8
▉Cleaning.........................8
▉Warranty.........................9
▉Repair...........................9

1
一、簡述：
UT-P32差動測試棒提供一個安全的儀器給所
有的示波器使用，它可以轉換由高輸入的差動
電壓(≤3000VPEAK)進入 一個低壓(≤7V)，並
且顯示波形在示波器上，頻率達 50MHz，非 常
適合大電力測試、研發、維修使用。
差動測試棒輸出標示是設計在操作示波器
1MΩ的輸入阻抗的相對衰減量，當使用 50Ω匹
配器進衰減量剛好爲 2倍量。 UT-P32 差動測試
棒,也建議選購本公司生産的 PL-10 阻抗轉換
器,可 以延伸差動測試棒的應用範圍-可以在電
錶上觀測更精確的實際測量電壓 值(示波器精
確度爲 1%,數位電錶約精准 10 倍)。
二、規格：
(1) 頻寬：
DC-50MHz
(2) 衰減：x100,x1000
(3) 精確度：±1%
(4) 輸入電壓範圍(DC+AC PEAK TO PEAK)
≤300Vforx100,(約100V RMS 或DC)

2
≤3000Vforx1000,(約1000V RMS 或DC)
(5) 允許最高輸入電壓：
最高差動電壓：
3000V(DC+AC PEAK TO PEAK)
輸入端及接地端間最高電壓：5KV RMS
(6) 輸入阻抗：
差動：8MΩ/1pF
單端到接地端間的輸入阻抗：4MΩ/2pF
(7) 輸出電壓：≤7V
(8) 輸出 阻抗：50Ω
(9) 上升時間：
≤7ns
(10) 雜訊抑制率：
50Hz:＞80dB;100KHz:＞60dB;1MHz:＞50dB
(11) 指定外接 6V DC 電源
(12) 耗電：最大耗電量 150mA(0.9 瓦特)
三、操作環境及狀況
(1)尺寸及重量：69x26x165mm;
(2)電子安全規範IEC1010-1
雙絕緣
安裝類目Ⅲ
污染程度 2
一般狀態
使用操作中
儲存
溫度
+20℃…+30℃
0℃….+50℃
-30℃….+70℃
濕度
≤70%RH
10%…85%RH
10%…90%RH

3
相關電壓或最大接地：5KV RMS
CE：EN50081-1 及50082-1
四、操作程式
將BP-250與UT-P32的輸出端連接，並與示波
器連結。
如有需要先調整示波器上的垂直開關。
將示波器上的衰減率及垂直開關調整到一致的
位置，如下表。
注意：電源必須打開。
(注意)
實際的垂直偏向是等於衰減乘上示波器上所選擇
的垂直偏向，例如是使
用負載50Ω的兩倍。
五、維護
保養此産品時請使用原廠指定的工具，原廠將
不負任何責任由其他不被認可的維修人員所
做的維修。
衰減
X1000
X100
輸 入 電 壓
(DC+ACPeak)
3000v
300v

4
六、清潔
此産品不需要任何特定的清潔，如有需要，請
用輕軟乾淨的布沾上微量的清潔液輕輕的在産
品外觀擦拭。
七、保固
除了在人爲上的特意損壞，本産品是受保固並
可以維修的，並不包含在安全規範的責任。
保固是以不超出發票上的金額，零件的更換及
運送的費用。
保固是僅在正常操作下而造成的損壞，並不包
含任何刻意的損壞，操作上的錯誤，機械上的
操作不當，保養不當，負載或過壓。
原廠的保固是賣出後的 12 個月內，如有任意
的非原廠的維修或更換零件，原廠保固將自然
取消。
八、維修
有任何的維修，保養或更換零件是在保固以外，請
將産品退回原廠維修。

5
UT-P32
1.Features
The UT-P32 differential probe provides a safety
means for measuring differential voltage to all
models of oscilloscopes.It can convert the high
differential voltage(≤3000Vp-p) into a low
voltage(≤7V)and display on the oscilloscope.Its
bandwidth is up to 50MHz,which is ideal for big
power testing,development and maintain.
The UT-P32 is designed to operate with the 1MΩ
impedance oscilloscopes. When combine with the
50Ω load , the attenuation will be 2 times.
UT-P32 is recommend to use with our own
manufactured PL-10 to expand the measuring with
the electricity meter to observe more accurate
measurement.The accuracy of oscilloscope is 1%
and the DMM is less than 1%)
2.Specifications
(1) Bandwidth:DC-50MHz
(2) Attenuation: X1000,X100
(3) Accuracy:+/-1%
(4) Input voltage range(DC+AC PEAK TO PEAK )

6
≤3000V for x1000,(about 1000V RMS and 1500V DC)
≤300V for x100,(about 100V RMS and 150V DC )
(5) Permitted max input voltage:
Max differential voltage: 3000V(DC+AC PEAK
to PEAK)
Max voltage between each input terminal and ground:
5KV RMS
（6）Input Impedance:
Differential: 8MΩ /1pF
Between terminal and ground:4MΩ /2pF
（7）Output voltage: ≤7V
（8）Output impedance: 50Ω
(9) Rise time:
7ns
(10)Rejection rate on common mode:
60Hz:＞80dB;100Hz:＞60dB;1MHz:＞50dB

7
(11)Power Supply:Only External 6V DC power
supply.
(12)Consumption: 150mA max (0.9 Watt)
3.Operatingenvironmental conditions
(1) Dimensions and weight：69x26x165mm; 500g
(2) Electrical safety to IEC 1010-1
Dual insulation
Installation category Ⅲ
Degree of Pollution 2
Related voltage or max line-earth：5KV RMS
CE：EN50081-1 and 50082-1
4.Operating procedure
․Connect the probe to the oscilloscope with the
insulated BNC/BNC lead.
․Adjust the vertical zero adjustment of the
oscilloscope if necessary.
Reference
Use
Storage
Temperature
+20℃…+30℃
0℃….+50℃
-30℃….+70℃
Relative Humidity
≤70%RH
10%…85%RH
10%…90%RH

8
․Select the attenuation ratio* and the vertical
deviation of the oscilloscope in accordance with the
conversion table below.
․NB: The POWER light must come on.
[N.B]
The real vertical deviation in V/div is equal to the
attenuation factor multiplied by the range of vertical
deviation selected on the oscilloscope. It will be doubled
in the case of use of a 50 Ω load.
▉Maintenance
For maintenance,only use specified spare
parts.The manufacturer can not be held
responsible for any accident arising following a
repair made other than its after sales service or
approved repairs.
Attenuation ratio
X1000
X100
Voltage Input Range
(DC+AC Peak to PEAK)
3000V
300V

9
▉Cleaning
This probe does not require any particular
cleaning.If necessary,clean the case with a cloth
slightly moistened with the soapy water.
▉Warranty
Unless notified to the country,our instruments
are guaranteed against any manufacturing defect
or material defect. They do not bear the
specification known as the safety specification.
Our guarantee,which may not under any
circumstances exceed the amount of the invoiced
price,goes on further than the repair of our faulty
equipment,carriage paid to our workshops.
▉Repair
Maintenance,repairs under or out of
guarantee.Please return the product to the
manufacturer.