Unitech MS852DPM ESD User manual

2D Imager Scanner
- MS852DPM ESD -
User's Manual
Version 1.1

Revision History
Date
Change Description
Version
20230203
First Published Version
1.0
20230208
Update 1.1 Package Optional Accessories
1.1

i © 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
About This Manual
Preface
Thank you for purchasing the Unitech product.
This manual explains how to install, operate and maintain our product.
No part of this publication may be reproduced or used in any form, or by any
electrical or mechanical means, such as photocopying, recording, or
information storage and retrieval systems, without permission in writing from
the manufacturer. The material in this manual is subject to change without
notice.
Regulatory Compliance Statements
FCC Warning Statement
This device has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference with radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference with radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to

ii © 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
1. This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
2. This device complies with FCC RF radiation exposure limits set forth for
an uncontrolled environment. To maintain compliance with FCC RF
exposure requirements, avoid direct contact to the transmitting antenna
during transmitting.
3. Any changes or modifications (including the antennas) made to this device
that are not expressly approved by the manufacturer may void the user’s
authority to operate the equipment.
FCC Label Statement
This device complies with part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
European Conformity Statement
Unitech Electronics co., Ltd herewith declares that the Unitech product is in
compliance with the essential requirements and all other provisions of the RED
2014/53/EU directive.
The declaration of conformity is available for download at :
https://portal.Unitech.eu/public/Safetyregulatorystatement

iv © 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
RoHS Statement
This device conforms to RoHS (Restriction Of
Hazardous Substances) European Union regulations
that set maximum concentration limits on hazardous
materials used in electrical and electronic equipment.
Waste electrical and electronic equipment (WEEE)
Unitech has set up a policy and process to meet the
2012/19/EU concerning electronic waste disposal.
For more detailed information of the electronic waste
disposal of the products you have purchased from
Unitech directly or via Unitech’s resellers, you shall either
contact your local supplier or visit us at :
https://portal.Unitech.eu/public/WEEE

v © 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
Laser Information
The Unitech product is certified in the U.S. to conform to the requirements of
DHHS/CDRH 21CFR Subchapter J and to the requirements of IEC 60825-1.
Class I and Class 1 products are not considered to be hazardous. The Unitech
product contains internally a Visible Laser Diode (VLD) whose emissions do
not exceed the maximum limits as set forth in the above regulations. The
scanner is designed so that there is no human access to harmful laser light
during normal operation, user maintenance or prescribed service operations.
The laser safety warning label required by the DHHS/IEC for the Unitech
product’s optional laser scanner module is located on the memory
compartment cover, on the back of the unit.
* Laser information only applies to the products with laser components.
CAUTION! Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous laser
light. Use of optical instruments with the scanner, including
binoculars, microscopes, and magnifying glasses, with will
increase eye damage.This does not include eyeglasses worn by
the user.
LED Information
The Unitech product contains LED indicator(s) or LED ring whose luminance is
not harmful to human eyes during normal operation, user maintenance or
prescribed service operations.
*LED information only applies to the products with LED component

xi © 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
Hearing Damage Warning
To prevent possible hearing damage, do not listen at high volume levels for long periods.

xii © 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
Worldwide Support
Unitech’s professional support team is available to quickly answer questions or
assist with technical-related issues. Should an equipment problem occur,
please contact the nearest Unitech regional service representative.
For complete contact information please visit the Web sites listed below:
Taipei, Taiwan –Headquarters
Europe
Tel:
[phone]
Tel:
[phone]
E-mail:
[email protected]
E-mail:
[email protected]
Address:
5F, No. 136, Lane 235, Baoqiao Road, Xindian
District, New Taipei City 231, Taiwan (R.O.C.)
Address:
Website:
Kapitein Hatterasstraat 19, 5015 BB,
Tilburg, the Netherlands
http://eu.ute.com
Website:
http://www.ute.com
China
Japan
Tel:
[phone]
Tel:
[phone]
E-mail:
[email protected]
E-mail:
[email protected]
Address:
Website:
Room401C, 4F, RIHUA International Mansion,
Xinfeng 3nd Road, Huoju Hi-tech District,
Xiamen, Fujan , China
http://cn.ute.com
Address:
Website:
Tosei Building 3F., 1-8-10
Nihonbashi-Hakozakicho, Cyuouku,
Tokyo, 103-0015, Japan
http://jp.ute.com
Asia & Pacific / Middle East
Latin America
Tel:
[phone]
Tel:
[phone]
E-mail:
[email protected]
[email protected]
[email protected]
E-mail:
Address:
[email protected]
17171 Park Row, Suite 210
Houston, TX 77084USA (Rep.)
Address:
4F., No. 236, ShinHu 2nd Rd.,
NeiHu Chiu, 114, Taipei,Taiwan
Website:
http://latin.ute.com
Website:
http://apac.ute.com / http://mideast.ute.com
North America
Please scan QR Code to visit us :
Tel:
[phone]
E-mail:
Address:
Website:
[email protected] / [email protected].com
6182 Katella Ave, Cypress, CA 90630, USA
http://us.ute.com

xiii
© 2022 Unitech Electronics Co., Ltd.All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
Warranty Policy
The following items covered under the Unitech Limited Warranty are free from
defects during normal use:
The warranty period is varied from each country. Please consult with your
supplier or Unitech local office for actual length of warranty period to your
purchased product.
Warranty becomes void if equipment is modified, improperly installed or used,
damaged by accident or neglect, or if any parts are improperly installed or
replaced by the user.

xiv
© 2022 Unitech Electronics Co., Ltd.All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
Table of Contents
Preface...........................................................................................................i
Regulatory Compliance Statements..............................................................i
Laser Information .........................................................................................v
LED Information ...........................................................................................v
Hearing Damage Warning...........................................................................xi
Worldwide Support..................................................................................... xii
Warranty Policy ..........................................................................................xiii
Chapter 1 - Overview................................................................................1
1.1 Package .................................................................................................1
1.2 Product Detail.........................................................................................2
1.3 Specifications .........................................................................................3
1.4 Getting Started .......................................................................................5
1.5 LED / Beeper Indicator...........................................................................7
Chapter 2 –Command Settings ............................................................8
2.1 Barcode Programming ...........................................................................8
2.2 General Setting ......................................................................................9
2.3 USB Device Type .................................................................................10
2.4 USB Interface.......................................................................................11
2.5 Scan Mode...........................................................................................19
2.6 Sense Mode (Image Change) Sensitivity.............................................19
2.7 Aiming ..................................................................................................20
2.8 Illumination Level..................................................................................21
2.9 Beeper Control.....................................................................................22
2.10 Decode Settings.................................................................................23
Chapter 3 - Symbology...........................................................................25
3.1 Symbology Overview............................................................................25
3.2 UPC-A..................................................................................................27
3.3 UPC-E..................................................................................................30

xv
© 2022 Unitech Electronics Co., Ltd.All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
3.4 EAN-8...................................................................................................32
3.5 EAN-13.................................................................................................35
3.6 Code 128..............................................................................................37
3.7 Code 39................................................................................................39
3.8 Code 93................................................................................................42
3.9 Codabar................................................................................................43
3.10 Plessey...............................................................................................46
3.11 MSI.....................................................................................................48
3.12 Interleaved 2 of 5................................................................................51
3.13 Data Matrix.........................................................................................53
3.14 QR Code ............................................................................................54
3.15 Micro QR Code...................................................................................55
3.16 AIM ID ................................................................................................55
3.17 Prefix..................................................................................................56
3.18 Suffix ..................................................................................................58
Chapter 4 - Data Editing ........................................................................60
4.1 Convert GS Code to OtherASCII Code ...............................................60
4.2 Truncate Data.......................................................................................61
4.3 Terminating Character..........................................................................63
Appendix A - Numeric Barcodes.........................................................64
Appendix B - Symbologies Barcodes ................................................66
Appendix C - ASCII Code Barcodes ...................................................70
Appendix D - Function Key Barcodes ...............................................83
Appendix E - AIM ID Table ....................................................................87

1© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
Chapter 1 - Overview
1.1 Package
Please make sure the following contents are in the MS852DPM ESD gift box.
If something is missing or damaged, please contact your Unitech
representative.
The Package Contents
USB Type-C Cable
Quick Start Guide
Optional Accessories
Standard Hands Free Stand
Protective Case

2© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
1.2 Product Detail
1.2.1 MS852DPM ESD Product View
LED Indicator
Scan Window
Scanner Trigger Key

3© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
1.3 Specifications
Optical & Performance
Sensor
1280 X 800 resolution
Aiming Element
650nm Laser Diode
Illumination
White LED
Ambient Light
0~8,600 Lux（Candles）
0~100,000 Lux (direct sunlight)
Scan Rate
70 FPS
Skew Angle
±55°
Pitch Angle
±55°
Roll Angle
±360°
Field of View
46°(H) x 29°(V)
Optical Resolution
1D : ≥3 mil ; 2D : ≥5 mil
Printing Contrast Scale
≥20% (UPC/EAN 100% , PCS 90%)
Depth of Field
Code39 (4 mil): 50 mm ~180 mm
EAN -13 (13 mil): 60 mm ~285 mm
QR Code (7 mil): 55 mm ~150 mm
Data Matrix (7 mil) : 55 mm ~160 mm
Electrical
Operation Voltage
4 VDC to 5.5 VDC
Current Consumption
Operating: 252mA
Standby: 77mA
Indicator
Buzzer, LED
Symbologies
1D
UPC-A, UPC-E, EAN-8, EAN-13, Code128,
Code 39, Code 93, Codabar, Plessey, MSI,
Interleaved 2 of 5
2D
Data Matrix , QR , Micro QR
DPM Barcodes
Data Matrix , QR , Micro QR
Regulatory Approvals
CE, FCC, BSMI, VCCI

4© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
Communication
Host Interface Supported
USB (HID; CDC)
Mechanical
Dimensions
87.8 L x 71.6 W x 177.7 H (mm)
Weight
165g without cable
Trigger Switch Life
10 million times
Environmental
ESD Protection
Functional after 8K Contact and 15K Air
Mechanical Shock
2.1M onto concrete (scanner only)
Operating Temperature
-10°C to 50°C (14°F to 122°F)
Storage Temperature
-40°C to +70°C (-40°F to +158°F)
Relative Humidity
95% non-condensing
IP Rating
IP42
Accessories
․Standard Hands Free Stand (Optional)
․USB Cable

5© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
1.4 Getting Started
1.4.1 Connecting the scanner
Connect USB cable to the USB port of a host computer.

6© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
1.4.2 Test & Finish
Open a word processing program such as Microsoft Word or Notepad, and
scan the following barcode:
If the word “Unitech” appears on the screen, you have successfully installed
your scanner.
Note: To scan a barcode, make sure the laser aimer is pointed directly at the
barcode.

7© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
1.5 LED / Beeper Indicator
Definition
Green LED Light
Beep / Sound
Power On
Three short beeps
(tone: low-mid-high)
Standby Mode
Good Read
Green light ON
One short beep
Enter Setting Mode
Two long beeps
Good Read
(During Setting Mode)
One long beep
Exit Setting Mode
(Setting Successful)
Three short beeps
(tone: low-mid-high)
Exit Setting Mode
(Setting Failed)
Three short beeps
(tone: high-high-high)

8© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
Enter Setup
Exit Setup
Chapter 2 –Command Settings
2.1 Barcode Programming
Use of Programming Barcodes
Before starting scanning any setting barcode, please do follow the
instruction below. Scanning the Enter Setup barcode can enable the engine
to enter the setup mode. Then you can scan a number of programming
barcodes to configure your engine. To exit the setup mode, scan the Exit Setup
barcode.
Enter Setup
Exit Setup

9© 2022 Unitech Electronics Co., Ltd. All rights reserved.
Unitech is a registered trademark of Unitech Electronics Co., Ltd.
All product and company names are trademarks, service marks, or registered trademarks of their respective owners
MS852 DPM ESD User’s Manual
Enter Setup
Exit Setup
2.2 General Setting
2.2.1 Factory Default
2.2.2 Custom Defaults
Write to Custom Defaults
Custom default parameters can be configured to set unique default values for
all parameters. After changing all parameters to the desired default values,
scan the Write to Custom Defaults barcode below to configure custom
defaults.
Restore Custom Defaults
If custom default values were configured (see Write to Custom Defaults), the
custom default values are set for all parameters each time the Restore
Defaults barcode below is scanned.
Write to Custom Defaults
Restore Custom Defaults
Set Factory Defaults