4. Press CH-. The
Navigator’s
red light will blink
twice.
The CABLE key is now unlocked and ready to be
reprogrammed. When you are finished reprogramming the
CABLE key, you can then lock in the code. To reprogram
the CABLE key:
1. Turn on your Cable Converter.
2. Press CABLE and release. Press and hold
SETUP until the
Navigator’s
red light blinks
twice, then release SETUP.
3. Enter the first three-digit Cable Converter code
listed in the “SET UP CODES FOR CABLE
CONVERTERS” section. If you perform this
procedure correctly, the red light will blink
twice.
4. Aim the
Navigator
at your Cable Converter and
press POWER. Your Cable Converter should
turn off. If your Cable Converter does not
respond, repeat steps 2-4, trying each code
listed for your brand until you find the one that
operates your Cable Converter.If you still
cannot get your Cable Converter to work with
the
Navigator
, try searching for your code as
outlined in the “Searching ForYour Code”
section.
5. Your
Navigator
is now programmed to
operate your Cable Converter. Write
your Cable Converter code in the
boxes to the left for future reference.
Remember, if you want to use your
Navigator
to operate
your Cable Converter, press the CABLE key first.
NOTE: The CABLE key can be programmed with codes
for DBS Satellites. To program your DBS Satellite, follow
the steps above, entering the three-digit code for your DBS
Satellite instead of the three-digit code for your Cable
Converter.
To lock in the code after you have reprogrammed the
CABLE key:
1. Press and release CABLE.
2. Press and hold SETUP until the
Navigator’s
red
light blinks twice.Release SETUP.
3. Press 9- 9- 7. The
Navigator’s
red light will
blink twice.
4. Press CH+. The
Navigator’s
red light will blink
twice.
Optimus 021
Panasonic 000,021, 107
Panther 637
Paragon 000
Philips 153,242
Pioneer 533,144, 753
Prelude 770
Pulsar 000
RadioShack 315
RCA 021
Regal 020,259, 273
Runco 000
Samsung 040,144
Scientific
Atlanta 477,008, 277
Signal 040
SL Marx 040
Sprucer 021
Starcom 003
Stargate 040,770
Tandy 258
TeleCaption 221
Teleview 040
Timeless 418
Tocom 012
Toshiba 000
TV86 063
Unika 022,153
United
Cable 003
Universal 022, 153, 191
Viewstar 063, 258
Zenith 525,000
SETUP CODES FOR
CABLE CONVERTERS
ABC 003,008, 014
Allegro 153,315
Antronix 022
Archer 022,153, 797
Cabletenna 022
Cableview 022
Century 153
Citizen 153,315
Comtronics 040
Contec 019
Digi 637
Emerson 797
Everquest 040
Garrard 153
Gemini 242
General
Instrument 476, 003, 276
Goldstar 040,144
Goodmind 797
Hamlin 009,020, 259, 273
Jasco 153,315
Jerrold 476,276, 003, 012,
014
Memorex 000
Movie Time 063
Novaplex 618
NSC 063
Oak 019
SETUP CODES FOR DBS
SATELLITES
AlphaStar 772
Echostar 775
HTS 775
Hughes
Network
Systems 749
5. Your
Navigator
is now programmed to
operate your Audio Component. Write
your Audio Component code in the
boxes to the left for future reference.
Remember, if you want to use your
Navigator
to operate
your Audio Component, press the AUDIO key first.
NOTE: For complete functionality of your Stereo
Components you may need to try both Amplifier codes and
Tuner/Receiver codes.
Jerrold 627
Pace 455
Panasonic 701
Primestar 627
RCA 566
Scientific
Atlanta 355
Sony 639
When you receive your
Navigator
, channel changing will
be limited to the CABLE mode through a feature called
Channel Lock. The Channel Lock feature limits channel
changing (e.g. CH +/-, 0– 9keys, ENTER and LAST) to
the CABLE mode, even when the
Navigator
is in the TV or
VCR mode. To unlock the Channel Lock feature to allow
channel changing in the TV andVCR mode:
1. Press and hold SETUP until the
Navigator’s
red light blinks twice.Release SETUP.
2. Press 9- 9- 6. The
Navigator’s
red light will
blink twice.
3. Press CH-. The
Navigator’s
red light will blink
twice.
Now, each individual mode (TV, VCR and CABLE) will
control channel changing.
NOTE: The Channel Lock feature, whether it is locked or
unlocked, will not effect the AUDIO mode.
To reactivate the Channel Lock feature to limit channel
changing to the CABLE mode:
1. Press and hold SETUP until the
Navigator’s
red light blinks twice.Release SETUP.
2. Press 9- 9- 6. The
Navigator’s
red light will
blink twice.
3. Press CH+. The
Navigator’s
red light will blink
twice.
To program the
Navigator
to operate your Audio
Component (CD Player, Receiver,Amp or Digital Audio
Service):
Look at the brand name of your Audio Component and
then write it in the space below.
Audio Brand:
Locate the brand name of your Audio Component in the
“SETUP CODES FOR AUDIO COMPONENTS”section.
The brands are listed in alphabetical order with the most
popular codes listed first. You will use one of these codes
to program your
Navigator
to operate your Audio Component.
To program the
Navigator
to operate your Audio Component:
1. Turn on your Audio Component. If you are
setting up a CD Player, turn on your CD Player
and insert a compact disc.
2. Press AUDIO and release. Press and hold
SETUP until the
Navigator’s
red light blinks
twice,then release SETUP.
3. Enter the first three-digit Audio Component
code listed in the “SET UP CODES FOR
AUDIO COMPONENTS”section. If you
perform this procedure correctly, the red light
will blink twice.
4. Aim the
Navigator
at your Audio Component
and press POWER. If you are setting up a CD
Player, aim the
Navigator
at your CD Player
and press PLAY. Your Audio Component
should turn off or your CD Player should play
your disc. If your Audio Component does not
respond, repeat steps 2-4, trying each code
listed for your brand until you find the one that
operates your Audio Component.If you still
cannot get your Audio Component to work with
the
Navigator
, try searching for your code as
outlined in the “Searching ForYour Code”
section.
Searching ForYour Code
If your TV,VCR, Cable Converter or Audio Component
does not respond to the
Navigator
after trying all of the
codes listed for your brand, or if your brand is not listed at
all, try searching for your code. For example, after trying
all of the codes for yourTV, you still cannot get the
Navigator
to operate yourTV, then:
1. Turn on your TV.
2. Press TV and release. Press and hold SETUP
until the
Navigator’s
red light blinks twice, then
releaseSETUP.
3. Press 9 - 9 - 1.
4.
Slowly
alternate between pressing POWER*
and TV until your TV turns OFF. Make sure
that the
Navigator
is aimed at your TV during
the search. You may have to press this
sequence of buttons (POWER* then TV) up to
100 times to search the entire library of codes.
5. When your TV turns OFF, press and release
SETUP to lock in the code for yourTV. Your
Navigator
is now programmed to operate your
TV.
NOTES: To search for the codes of your other
components, repeat Steps 1 through 4, only substitute the
appropriate device key (VCR, CABLE or AUDIO) for the
component you are searching for.
*If you are searching for yourVCR or CD Player code, you
may want to use the PLAY key instead of the POWER key
to search for your code. When your VCR or CD Player
starts to play, press SETUP to lock in your code.
LearningThe Codes Programmed
IntoThe
Navigator
If you have set up the
Navigator
using the “Searching For
Your Code” procedure, you may need to find out which
three-digit code is operating your equipment.Use this
procedure
after you have set up your components
to find
out which three-digit code is operating your equipment.
For example, to find out which code is operating your TV:
1. Press TV and release. Press and hold SETUP
until the
Navigator’s
red light blinks twice, then
releaseSETUP.
2. Press 9 - 9 - 0.
3. For the first digit of your three-digit code, press 1,
wait 3 seconds and count the number of times the
red light (LED) blinks on the
Navigator
. If the light
does not blink when you press the number 1, the
digit is zero.
4.For the second digit, press 2, wait 3 seconds
and count the number of times the red light
(LED) blinks on the
Navigator
. If the light does
not blink when you press the number 2, the
digit is zero.
5. For the third and final digit, press 3, wait 3
seconds and count the number of times the
red light (LED) blinks on the
Navigator
. If the
light does not blink when you press the number
3, the digit is zero. Now you have your
three-digit code.
NOTE: To find the code for your other components, repeat
Steps 1 through 5, only substitute the appropriate device
key (VCR, CABLE or AUDIO) for the component you wish
to get the code for.
Re-Assigning Device Keys
You can use the
Navigator
to operate a second TV or a
second VCR or any combination of four home entertainment
components. For example, you may want your
Navigator
to
control 1 TV, 1 Cable Converter and 2 VCRs. To accomplish
this, you must re-assign one of the keys to operate the
desired component, in this case, a second VCR. Please note
that the CABLE key cannot be re-assigned. The chart below
shows you how to re-assign a particular device key and then
set up your new component.
TV to VCR SETUP* + 992 + VCR + TV + TV +
SETUP* + VCR code.
TV to AUDIO SETUP* + 992 + AUDIO + TV + TV +
SETUP* + Audio Component code.
VCR to TV SETUP* + 992 + TV + VCR + VCR +
SETUP* + TV code.
VCR to AUDIO SETUP* + 992 + AUDIO + VCR + VCR +
SETUP* + Audio Component code.
AUDIO to TV SETUP* + 992 + TV + AUDIO + AUDIO
+ SETUP* + TV code.
AUDIO to VCR SETUP* + 992 + VCR + AUDIO +
AUDIO + SETUP* + VCR code.
*
NOTE: Here you must hold SETUP until the Navigator’s
red light blinks twice.
Volume Lock
When you receive your
Navigator
, volume control is
operated through yourTelevision using a feature called
Volume Lock. If your TV is not remote controllable, or if
you would like the volume to be controlled by a different
component, you can change the Volume Lock setting to
control the volume through the
CABLE, VCR or AUDIO
mode. Changing the Volume Lock setting to the CABLE or
VCR mode will change the volume control for all modes
except AUDIO, which will continue to control its own
volume. If you change the Volume Lock setting to the
AUDIO mode, all modes (TV,VCR, CABLE and AUDIO)
will be controlled by the AUDIO mode. To change the
Volume Lock setting on the
Navigator
to the CABLE or
AUDIO mode:
1. Press and hold SETUP until the
Navigator’s
red
light blinks twice, then release SETUP.
2. Press 9 -9 - 3. The
Navigator’s
red light will
blink twice.
3. Press and release CABLE or AUDIO. The
Navigator’s
red light will blink twice.
Now, whenever you press VOL+ , VOL- or MUTE on the
Navigator
, your cable converter or audio component will
control the volume.
If you have aTV/VCR combination that does not use a TV
code to control the volume, you can access the volume in
the VCR mode. To change the Volume Lock setting on the
Navigator
to the VCR mode:
1. Press and hold SETUP until the
Navigator’s
red
light blinks twice, then release SETUP.
2. Press 9 -9 - 3. The
Navigator’s
red light will
blink twice.
3. Press and release VCR. The
Navigator’s
red
light will blink twice.
Now, whenever you press VOL+ , VOL- or MUTE on the
Navigator
, yourTV/VCR combo will control the volume.
To return the Volume Lock setting to the TV mode:
1. Press and hold SETUP until the
Navigator’s
red
light blinks twice, then release SETUP.
2. Press 9 -9 - 3. The
Navigator’s
red light will
blink twice.
3. Press and release TV. The
Navigator’s
red
light will blink twice.
Now, whenever you press VOL+ , VOL- or MUTE on the
Navigator
, your TV will control the volume.
Troubleshooting
Problem Solution
Red light does not
blink or blinks 5 times
when you press a
key?
The red light blinks
when you press a key
but you receive no
response from your
home entertainment
component?
The
Navigator
does
not operate your home
entertainment
components or is not
performing commands
properly?
Problems
programming a
TV/VCRcombo?
VCR not recording?
No volume on a 2nd
TV ?
Channel +/- and
LAST not working for
your RCATV?
Problems changing
channels?
Replace the batteries with four
(4) new AAA alkaline batteries.
Make sure you are aiming your
Navigator
at your home
entertainment component and
that you are within 15 feet of the
component you are trying to
operate before using your
remote.
Try all of the codes listed for your
brand of home entertainment
component in the “Set-Up
Codes” section. Many setup
codes may allow for partial
functionality, however, only one
setup code will operate your
home entertainment component
correctly. Make sure that all of
the components you are
setting up are able to be
operated with an infrared
remote control.
Use the VCR setup codes for
your brand. Some combo units
may require both aTV code to
control volume and aVCR code
for full operation.
As a safety feature on the
Navigator
, you must press the
REC key twice.
Press and hold SETUP until the
Navigator’s
red light blinks twice.
Release SETUP and enter 9-9-3
followed by VOL +.
Due to RCA design (1983-1987),
only the original remote control
will operate these functions.
If your original remote control
required an ENTER keystroke
when changing channels, press
the ENTER key on the
Navigator
after you enter the channel
number.
World Wide Web: http://www.oneforall.com
The UNIWAND “
Navigator
” does not have any user
serviceable parts. Opening the case, except the battery
cover, may cause permanent damage to your UNIWAND
“
Navigator
”.
Uniwand is a trademark of Universal Electronics Inc.
Copyright 1998 by Universal Electronics Inc. No part of
this publication may be reproduced, transmitted,
transcribed, stored in any retrieval system, or translated to
any language, in any form or by any means, electronic,
mechanical, magnetic, optical, manual, or otherwise,
without the prior written permission of Universal
Electronics Inc.
URC-44XXX BO2/BO4 McK
M4078 2/98
CH
-
CABLE
SETUP
POWER
SETUP
CABLE
9 - 9 - 7
9 - 9 - 7
CH
+
9 - 9 - 1
9 - 9 - 1
POWER
PLAY
AUDIO
SETUP
9 - 9 - 6
9 - 9 - 6
SETUP
9 - 9 - 6
9 - 9 - 6
SETUP
CH
-
CH
+
SETUP CODES FOR
AUDIO COMPONENTS
Setup Codes For CD
Players
Aiwa 124,157
Burmester 420
California
Audio Lab 029
Carver 157, 179, 437
Denon 003
DKK 000
Emerson 305
Fisher 048,174, 179
Garrard 393,420
Genexxa 032,305
Hitachi 032
JVC 072
Kenwood 028,037, 048, 190
Krell 157
Linn 157
LXI 305
Magnavox 157,305
Marantz 029,157, 180
MCS 029
Mission 157
MTC 420
Nikko 174
NSM 157
Onkyo 101
Optimus 000,032, 037, 048,
145,179, 305, 420,
437,468
Panasonic 029
Philips 157
Pioneer 032,244, 305, 468
Proton 157
QED 157
Quasar 029
RCA 179,305
Realistic 179,180, 420
Rotel 157,420
SAE 157
Sansui 157,305
Sanyo 179
Scott 305
Sears 305
Sharp 037, 180
Sherwood 180
Sony 000,185
Soundesign 145
Tascam 420
TEAC 174,180, 393, 420
Technics 029
Victor 072
Wards 157
Yamaha 036
Yorx 461
Setup Codes For
Receivers
ADC 531
Aiwa 121,158, 189
Capetronic 531
Carver 042, 189
Casio 195
Clarinette 195
Denon 004
Fisher 042,219
Garrard 463
Harman/
Kardon 110
JVC 074
Kenwood 027,186
Linn 189
Lloyd’s 195
LXI 181
Magnavox 189,195, 531
Marantz 039,189
MCS 039
Modulaire 195
NAD 320
Onkyo 135
Optimus 042,181, 186, 219,
531,670
Panasonic 039
Penney 195
Philips 189
Pioneer 150,531, 630
Quasar 039
RCA 054,530, 531
Realistic 181,195
Sansui 189
Sanyo 219
Sharp 186
Sherwood 502
Sony 158,474
Soundesign 670
TEAC 463
Technics 039,309, 518
Victor 074
Wards 042, 054, 158, 189
Yamaha 176, 186
Yorx 195
Setup Codes For
Amplifiers
Denon 160
GE 078
JVC 331
Luxman 165
Optimus 013,300, 395
Pioneer 013,300
Realistic 395
Sony 220,689
Soundesign 078,211
Technics 308
Victor 331
Wards 013, 078, 211
Yamaha 133, 354
Setup Codes For
Digital Audio Service
Jerrold 459,520
Scientific
Atlanta 460
Starcom 459
TV
SETUP
TV
SETUP
9 - 9 - 0
9 - 9 - 0
1
1
2
2
3
3
AUDIO
SETUP
9 - 9 - 3
9 - 9 - 3
CABLE
SETUP
9 - 9 - 3
9 - 9 - 3
VCR
SETUP
9 - 9 - 3
9 - 9 - 3
TV
POWER
TV
SETUP
