Universal Furniture 192625 User manual

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
192625 & 193625
Down Home Arm Chair
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts
or hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should
be periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or
cause injury. Always check to be sure all hardware on this list and the above mentioned components is
attached to the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Chair Back
1pc
B
Seat Frame
1pc
C
Left Leg & Arm
1pc
D
Right Leg & Arm
1pc
E
Side Stretcher (L&R)
2pcs
F
Front Stretcher
1pc
G
Back Cushion
1pc
Assembly Procedure:
Caution: Please do not over-tighten bolts during assembly.
Note: First read the chair leveling instructions. This is an additional assembly instruction sheet found
inside the carton.
Step 1: Place all chair parts on a soft and smooth surface.
Step 2: Take off plastic cover on upholstery seat. Assemble chair back (A) to back rail of seat frame
(B) using #3 (bolt + lock washer + flat washer).
Step 3: Assemble rear corner blocks of seat frame (B) with back post using #2 (bolt + lock washer +
flat washer).
Step 4: Assemble side stretchers (E) to chair back by using screws #4. Tighten screws with
screwdriver (Not provided).
Step 5: Assemble front corner blocks of seat frame (B) with right leg & arm (D) and left leg & arm (C)
using #1 (bolt + lock washer + flat washer). At the same time, assemble front legs to
stretcher using screws #4. Tighten screws with screwdriver (not provided). The front legs
are marked Left& Right. Then tighten all bolts completely using the wrench #5.
Step 6: Attach end of right leg & arm (D) and left leg & arm (C) to chair back (A) using #6 (bolt + lock
washer + flat washer) with allen wrench #8. Then, attach wooden plugs #7.
.
Step 7: Last put the back cushion (G) to the chair back.

GOOD, AFFORDABLE, SMART DESIGN.
INSTRUCTION SHEET
192625 & 193625
Down Home Arm Chair
Step 5, 6
Step 2, 3, 4
D
4
4
A
F
A
BD
F
G
Allen wrench
Wood pulg for arm
Hardware List
2
4
3
14pcs
1pc
1pc
NO
4pcs
6pcs
Qty.
For Both
Side
Chair&
Arm Chair
62pcs
2pcs
1pc
7
8
Only
Arm Chair
5Wrench
Bolt+Spring Washer+Flat Washer--5/16" Dia
3" L
2-1/2" L
1-1/2" L
1-1/2" L
Screw
Bolt+Spring Washer+Flat Washer--5/16" Dia
Bolt+Spring Washer+Flat Washer--5/16" Dia
Bolt+Spring Washer+Flat Washer--1/4" Dia
Step8: After making sure all bolts are attached and hand tightened, turn the chair over.
Step9: Level the chair following “Chair Leveling Instruction”. This is an additional assembly
instruction sheet found inside the carton.
Step10:Make sure the chair is level and tighten all bolts completely using the wrench supplied.
Assembly is now complete.