Universal Furniture Universal EXPLORE HOME 847-755 User manual

INSTRUCTION SHEET
847-755
Rect. Dining Table
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Table Top
1pc
B
Mounting Plate
1pc
C
Side Post
2pcs
D
Bottom Stretcher
1pc
E
Table Leaf
1pc
F
Leaf Bag
1bag
G
Hardware Pack
1bag
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Detach mounting plate (B) off table top (A) using wrench (1), keep the bolts, spring washers
and flat washers for step 4.
Step 3: Attach the side posts (C) to the bottom stretcher (D) with phillip head bolts (2), spring
washers (3), curved washers (6) and wood dowel (5) using wrench (1). Then attach the
mounting plate (B) to the side posts (C) with phillip head bolts (2), spring washers (3) and flat
washers (4) using wrench (1).
Step 4: Attach mounting plate (B) to table top (A) with the bolts, spring washers and flat washers
from step 2. Turn the table upright.
Step 5: Unlock table top (A), take off the table leaf (E) into leaf bag (F) when leaf is not in use. Then
lock the table top.
Note: If handled improperly, the act of installing and removing table leaf may damage the table.
Please use caution and delicate handling when installing and removing table leaf to prevent
damaging the table top surface and edges. It is best two persons are involved when installing
or removing table leaf.
Assembly is now complete.

INSTRUCTION SHEET
847-755
Rect. Dining Table
1
210PCS
1PC
310PCS
48PCS
5/16"*2-1/2"
87*19*2.5mm
5/16"
5/16"*23*2mmT
Q'TY
HARDWARE LIST(G)
WRENCH
PHILLIP HEAD BOLT
SPRING WASHER
FLAT WASHER
6
510*40MM 2PCS
2PCS
5/16"L32*13*8mm
WOOD DOWEL
CURVED WASHER
A
B
Step 2
12
365
4
32
1
C
D
Step 3
ON OFF
ONOFF
1
E
F
Step 4 Step 5