Universal Furniture 394-604 User manual

Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, screws, bolts, nuts and wooden plugs may loosen up. They should be
periodically inspected and re-tightened to prevent damage to the furniture and (or) personal property or cause
injury. Always check to be sure all hardware on this list and the above mentioned components is attached to
the furniture properly and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Chair Back
1 pc
B
Seat Frame
1 pc
C
Left Leg
1 pc
D
Right Leg
1 pc
E
H Stretcher
1 pc
F
Front Stretcher
1 pc
G
Upholstery Pad
1 pc
Assembly Procedure:
CAUTION: PLEASE DO NOT OVER-TIGHTEN BOLTS DURING ASSEMBLY.
NOTE: FIRST READ THE CHAIR LEVELING INSTRUCTIONS. THIS IS AN ADDITIONAL
ASSEMBLY INSTRUCTION SHEET FOUND INSIDE THE CARTON.
Step 1: Place all chair parts on a soft and smooth surface.
Step 2: Take off plastic cover on upholstery seat. Assemble Chair Back (A) to back rail of Seat
Frame (B) using-------#2 (bolt + spring washer + flat washer). Then, attach rear corner
blocks of Seat Frame (B) with back post using-------#1 (bolt + spring washer + flat washer).
Tighten with Wrench (5).
Step 3: Assemble the Front Stretcher (F) to the Left Leg (C) and Right Leg (D) using Screws (4).
Tighten screws with screwdriver. (Not provided).
Step 4: Follow the Label (BACK) on the back-end of H Stretchers (E), Inserts the H Stretchers (E)
into the Chair Back (A) using Screw (4). Do not over tighten.
Step 5: Assemble front corner blocks of Seat Frame (B) with Left Leg (C) and Right Leg (D) using--
-----#3 (bolt + spring washer + flat washer). Next, attach the H Stretchers (E) to Left Leg (C)
and Right Leg (D) using Screws (4). Tighten screws with screwdriver. (Not provided)
Step 6: After making sure all bolts are attached and hand tightened, turn the chair over.
INSTRUCTION SHEET
393/394/396-604
COUNTER CHAIR

Hardware List
2
4
3
1
Qty.
--
5
--
--M
--
Step 7: Put the Upholstery Pad (G) on the Seat Frame (B). Straighten the ribbon at the bottom of the cushion.
Joined with velcro on the seat frame.
Step 8: Level the chair following “Chair Leveling Instruction”. This is an additional assembly
instruction sheet found inside the carton.
Step 9: Make sure the chair is level and tighten all bolts completely using the wrench supplied.
Assembly is now complete.
(A)
(B)
(E)
(A)
(B)
(C)
(D)
(A)
(C)
(D)
(C) (D)
(E)
(F)
(F) (F)
(E)
(B)
(G)
(A)