Universal Furniture Bookcase Platform Bed User manual

General Single Ped. Table: 1 leaf, 1 bag, 4 bun feet, no leveler
Version 20081118
GOOD, AFFORDABLE, SMART DESIGN
Thank you for purchasing this quality product. Be sure to check all packing material carefully for small
parts that may have come loose inside the carton during shipment.
Caution: (1) These parts are cumbersome and heavy. This product can best be assembled with the
assistance of one or more persons in order to prevent personal injury and to insure parts are not damaged
during the assembly process. If dirty, clean finished parts with mild dishwashing liquid and water solution
applied on damp cloth. Cloth should not be excessively wet. Polish finish with soft cloth and an industry
recognized furniture polish.
(2) To prevent damage to your floor or carpet, please check the bottom of each piece of furniture for
stain residue and rough surfaces and also check for staples or nails left after removing the packaging material.
The manufacturer will not be held responsible if preventative steps are not taken prior to installation.
(3) Unpack and dispose of all packing material but be careful not to throw away any assembly parts or
hardware. Read the instruction sheet and parts list carefully. Remove all staples and screws used for
packaging carefully using pliers and or screwdrivers to prevent injury and scratching or damaging flooring.
(4) During normal use everyday, bolts and nuts may loosen up. They should be periodically inspected
and re-tightened to prevent damage to the furniture and (or) personal property or cause injury. Always check
to be sure all hardware on this list is attached to the furniture and kept tightened at all times.
PARTS LIST:
#
Description
Qty.
#
Description
Qty.
A
Headboard
1 pc
B
Footboard
1 pc
C
Storage Box
1 pc
D
Side Rail
1 pc
E
Slat Roll
1 pc
F
Center Support Leg
2 pc
Assembly Procedure: (Please follow the sketches below.)
Step 1: Unpack, inspect, and read assembly instruction carefully. Lay out the parts and hardware.
Make sure the quantity of each is correct.
Step 2: Put the storage box (C) upside down on a soft smooth surface to avoid damage or being
scratched. Screw the center support leg (F) into storage box (C).
Step 2: Attach storage box (C) to the headboard (A) and footboard (B) with head bolts (6) by using
Allen wrench (7). Insert the dowels (1) into the pre-drilled holes at both end of side rail (D).
Attach the side rail (D) to the headboard (A) and footboard (B) with brackets (2), lock
washers (3), nuts (4) and use the spanner (5) to tighten them. Note: The storage box and
side rail can be interchangeable.
Step 3: Screw the slat roll (D) onto side rails (C) with wood screws (8) by using Phillip head screw
driver (not provided).
Assembly is now complete.
2
1
3
4
4 PCS
HARDWARE LIST
6
51 PC
5/16"*3-1/2"
22*1.5
5/16" 70*30*5mm
1 PC
5/16"*3-1/2"
5/16"
7
8PCS
4 PCS
4 PCS
4 PCS
4 PCS
8
D o w e l Spanner
L o c k W a s h e r
N u t
B r a c k e t H e a d B o lt
A lle n W r e n c h
W o o d S c r e w
INSTRUCTION SHEET
Bookcase Platform Bed

General Single Ped. Table: 1 leaf, 1 bag, 4 bun feet, no leveler
Version 20081118
F
F
C
A
B
C
D
S te p 1 S te p 2
67
2345
S te p 3
8

General Single Ped. Table: 1 leaf, 1 bag, 4 bun feet, no leveler
Version 20081118